Page 2 - Important Safety Precautions; TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV SET; CAUTION: To reduce the risk of electric shock. Do not; RISK OF ELECTRIC SHOCK; CAUTION
2 Important Safety Precautions WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV SET TO RAIN OR MOISTURE. CAUTION: TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT. 1. Operate only from the power source specified on the unit.2. Avoid damaging the A...
Page 3 - IMPORTANT SAFETY INSTRUCTIONS
3 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install n...
Page 4 - Cautions for installation; POWER
4 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects ...
Page 5 - Warnings; Caring for the Cabinet
5 Warnings Caring for the Cabinet Caring for the Screen Normally, light dusting with a soft, non-scratching duster will keep your TV clean. If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly moistened with water. You can add a few drops of mild liq...
Page 6 - Cooling is also performed while the television is being shut down.; If; Do not block the ventilation holes.; The lamp is a consumable item
6 Thank you for purchasing JVC’s model HD-52G886, HD-52G786, HD-56G886 or HD-56G786 HDTV-ready projection television which uses the high-quality HD-ILA projection system. This is one of the highest quality and most technologically advanced televisions available today. It is recommended that you read...
Page 7 - Do not turn the power on and off repeatedly in a short amount of time.; If the lamp is used when there is dirt from
7 4. The television requires a lot of electrical power It is recommended that the television is connected directly to the wall socket, and not to another device. When connecting the television to a wall socket that is being used by another device, or when using an extension cord, be careful not to e...
Page 8 - Table of Contents; Important Safety Precautions . 2
8 Table of Contents Unpacking your TV . . . . . . . . . . . . 10TV Models . . . . . . . . . . . . . . . . 12 TV Remote Control . . . . . . . . . . . 14Getting Started . . . . . . . . . . . . . 15 The Remote Control . . . . . . . . . . 15 Connecting Your Devices . . . . . . . 16 Interactive Plug In M...
Page 10 - Television x 1; Remote Control x 1; Quick Setup Unpacking your TV; Two Way Splitter x 1
10 AA Batteries x 2 Television x 1 Remote Control x 1 Note: Your television and/or remote control may differ from the examples illustrated here. Quick Setup Unpacking your TV Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television, please check to make ...
Page 11 - Coaxial Cables
11 Quick Setup Unpacking your TV Used to connect an external antenna or cable TV system to your TV. Used to make video connections with S-Video VCRs, Camcorders and DVD players. We recommend that before you start using your new television, you read your entire User’s Guide so you can learn about you...
Page 12 - Quick Setup TV Models; Rear Panel Diagram; The terminal
12 Y Pb Pr L R AUDIO OUTPUT S-VIDEO INPUT-3 INPUT-1 AV COMPULINK - III VIDEO 75Ω (VHF/UHF) VIDEO (DIGITAL) L I AUDIO I R L I AUDIO I R VIDEO OVER OVER S-VIDEO Y Pb Pr INPUT-2 VIDEO CENTER CHANNELINPUT L R AUDIO L R AUDIO LICENSED UNDER THE FOLLOWING U.S. PATENTS6,183,0916,419,362 i.LINK IN/OUT S400(...
Page 13 - Side Panel Diagram; Front Panel Diagram; • For information on the LED, see page 92.
13 MODELS: HD-52G886, HD-52G786, HD-56G886, HD-56G786 Quick Setup TV Models Side Panel Diagram VOLUME INPUT 4 CHANNEL OPERATE + – + – MENU OVER S-VIDEO VIDEO L/MONO R AUDIO INPUT Front Panel Diagram POWER LAMP/PROGRAM POWER LAMP/PROGRAM LAMP/PROGRAM LED POWER BUTTONPOWER LED • For information on the...
Page 14 - Quick Setup TV Remote Control
14 MODELS: HD-52G886HD-52G786HD-56G886HD-56G786 Quick Setup TV Remote Control RM-C14G • For information on remote control buttons, see pages 67 - 77 and 81 - 86. • i.LINK MENU, TIMER, SUB CHANNEL, FAVORITE and GUIDE buttons are for digital channels. If your TV is connected to an ATSC antenna or Digi...
Page 15 - Quick Setup Getting Started; Getting Started; Key Feature Buttons; Hyperscan; Basic Operation; Turn the television on and off by pressing the P; button at the top right corner
15 These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new television right away. If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual. Before you can operate you...
Page 16 - Quick Setup Connections; Step 2 – Connecting Your Devices; • These connections are examples.; No VCR Connection; TV Rear Panel; Cable or Antenna
16 Quick Setup Connections Step 2 – Connecting Your Devices Used to make video connections with S-Video VCRs, Camcorders and DVD players. S-Video Cable Used to connect audio/video devices like VCRs, DVD players, stereo amplifiers, game consoles, etc. Component Cables Composite Cables Audio Cables To...
Page 17 - • You may also connect the DVD player to Input 1.; OR; VCR Connection
17 Quick Setup Connections Notes: • Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information. • Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete on...
Page 19 - Connecting to Monitor/Recording Output Terminal; images coming from the composite video input terminal.
19 Quick Setup Connections Connecting to Monitor/Recording Output Terminal Notes: • When you make this connection, set the Video-1 Monitor Out menu to ON. See page 57. • If you are receiving ATSC/Digital Cable signal, it can be outputted to the S-Video output terminal or Video (composite video) term...
Page 20 - • AV CompuLink can only be used with JVC brand products.; instruction book), using VCR A code will switch the TV to input 1.; Connecting to JVC AV Compu Link; AV CompuLink Cable; Plug one end of the AV CompuLink cable
20 JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player and the device will automatically turn on and begin playback. At the same time, using theAV CompuLink, the VCR or DVD player se...
Page 21 - connect an S-Video cable from the side of the TV to the camcorder.; Connecting to a Camcorder
21 Quick Setup Connections 1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on the side of the TV, OR connect an S-Video cable from the side of the TV to the camcorder. 2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on the side o...
Page 22 - Connecting to the Surround Amplifier; amplifier's CENTER CHANNEL OUTPUT terminal.; LEFT AUDIO INPUT on the amplifier.; Connecting to an External Amplifier
22 Quick Setup Connections Connecting to the Surround Amplifier CENTER CHANNELINPUT L R AUDIO Front CENTER CHANNEL OUTPUT (VARIABLE OUTPUT) TV Rear Panel Front Surround 1) Connect the Pin cable from the TV's CENTER CHANNEL INPUT terminal to the surround amplifier's CENTER CHANNEL OUTPUT terminal. No...
Page 23 - Connecting to an amplifier using your optical output; • This terminal can only output digital audio.
23 Quick Setup Connections Connecting to an amplifier using your optical output You can connect an amplifier that has an optical digital input terminal by using an optical digital cable from the optical output. The signal that is output can be PCM or Dolby Digital. i.LINK IN/OUT S400(TS) OPTICAL OUT...
Page 24 - Connecting to a Digital TV Receiver; the DIGITAL-IN on the back of your television.
24 Quick Setup Connections By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in their digital form. AV COMPULINK - III L R AUDIO _ AUDIO (DIGITAL) VIDEO (DIGITAL) TV Rear Panel DTV Decoder L R AUDIO OUT DIGITAL OUT HDMI to DVI Cable After the connections have ...
Page 25 - Connecting to an HDMI Compatible Device
25 By connecting an HDMI compatible device, high definition pictures can be displayed on your TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI compatible devices.HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all digit...
Page 28 - Connecting to the computer; Looking at the images from a computer
28 Quick Setup Connections This TV can be used as a computer screen. Use a commercially available D-SUB cable to connect the TV's PC INPUT terminal to the computer's analog RGB output terminal. If you want to listen to the sound from the computer, use a commercially available RCA cable to connect th...
Page 29 - Table of signals for each type of computer; When a picture is not displayed; Apple Macintosh is a registered trademark of Apple Computer, Inc.
29 Quick Setup Connections Table of signals for each type of computer Resolution 640 x 480(VGA) 1024 x 768(XGA) VerticalFrequency(Hz) 60.0 60.0 HorizontalFrequency(kHz) 31.5 48.4 When a picture is not displayed With some computers, some problems can be solved by changing the settings. Check the comp...
Page 30 - Step 3 – The Interactive Plug In Menu; Quick Setup Plug-In Menu; To choose a language:; Language
30 When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for: • The language in which you want the onscreen menus to appear. • Setting the TV’s clock to the correct time...
Page 31 - Manual Clock Set; operating any timer functions.; Auto Clock Set
31 To set your clock manually (without using the XDS signal), choose MANUAL. If you choose AUTO, see auto clock set above. √ ® To choose MANUAL † To TIME √ ® To set the hour † To minute √ ® To set the minute † To TIME ZONE √ ® To select your time zone: (Atlantic, Eastern, Central, Mountain, Pacific,...
Page 32 - STOP; Auto Tuner Setup; Cable Box and Satellite Users:; NOW
32 Quick Setup Plug-In Menu The Quick Setup is complete STOP In auto tuner setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals. This means when you scan (using the C HANNEL +/– buttons) you will recei...
Page 33 - button, then enter the first code number listed with the 10; not respond to any code, try the search codes function, on page 36.; Remote Programming; Setting the CATV, VCR and DVD Codes
33 You can program your remote to operate your cable box, satellite receiver, VCR or DVD player by using the instructions and codes listed below. If the equipment does not respond to any of the codes listed below or to the code search function, use the remote control supplied by the manufacturer. Th...
Page 34 - button, and confirm the operation of the VCR.; button on the remote and press P; VCR Codes
34 The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward, rewind, pause, record, channel up/down operation. 1) Find the VCR brand from the list of codes shown below.2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”. 3) ...
Page 35 - button, and confirm the operation of the DVD player.; DVD Codes
35 The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward, rewind, previous/next chapter, tray open/close, and still/pause operation. 1) Find the DVD player brand from the list of codes shown below.2) Slide the first 2-way selector switch to “TV” and the other 2-w...
Page 36 - Cable/Satellite Search Codes Function
36 Remote Programming Cable/Satellite Search Codes Function 1) Slide the first 2-Way Mode Selector switch to CATV.2) Press the P OWER and R ETURN +/TV buttons. Hold for at least three seconds and release. 3) Press the P OWER button on the remote, and see if the cable or satellite box responds. 4) If...
Page 37 - To bring up the onscreen menu; button on the remote control. The item that; Onscreen Menus; Using the Guide
37 To bring up the onscreen menu , press the M ENU button on the remote control. The item that appears in green is the one currently selected. If you use the Menu button on the TV’s side panel instead of the remote, an additional menu screen showing VIDEO STATUS and ASPECT will appear between INITIA...
Page 38 - The Onscreen Menu System
38 Your television comes with JVC’s onscreen menu system. The onscreen menus let you make adjustments to your television’s operation simply and quickly. Examples of the onscreen menus are shown on the next page. Detailed explanations on using each menu follow later in this guide. For information abo...
Page 39 - Press the M; button; between INITIAL SETUP 05 and PICTURE ADJUST 01 will appear.
39 Press the M ENU button Onscreen Menus TINT COLOR PICTURE BRIGHT DETAIL COLOR TEMPERATURE HIGH PICTURE ADJUST SELECT OPERATE EXIT MENU NEXT PAGE PREVIOUS 00 00 00 00 00 STANDARD (1/2) SELECT OPERATE EXIT MENU NEXT PAGE PREVIOUS STANDARD PICTURE ADJUST (2/2) OFF OFF OFF ON DIG. NOISE CLEAR COLOR MA...
Page 40 - Initial Setup
40 Initial Setup Auto Tuner Setup The auto tuner setup function is described on page 32 as the interactive plug-in menu. If you need to run the auto tuner setup again, follow the steps below. Press the M ENU button π † To AUTO TUNER SETUP √ ® To operate π † To TUNER MODE (IN ANALOG) √ ® To choose CA...
Page 41 - Channel Summary
41 Initial Setup Channel Summary Channel summary allows you to customize the line-up of channels received by your TV. Regarding analog channels, you can add or delete channels from the line-up or prevent any unauthorized viewers from watching any or all 191 channels. Regarding digital channels, the ...
Page 42 - Your characters are now set
42 Initial Setup How to set the channel label. (This is only for analog broadcasting.) Press the M ENU button π † To CHANNEL SUMMARY √ ® To operate π † To the ID column Press the O K button to enter √ ® To select the character you want π † To move to the next space ...continue to follow these direct...
Page 43 - Channel Guard Message
43 When a viewer attempts to watch a guarded channel, the following message appears: To watch a channel that you have locked, enter the Lock Code using the 10 key pad. If the wrong code is entered, the message “INVALID LOCK CODE!” will flash on the screen. The channel cannot be accessed until the co...
Page 44 - Directions to Block Unrated Programs; Unrated Programs
44 You can block programs that are not rated. Press the M ENU button π † To V-CHIP √ ® To operate (The lock icon appears) Press Z ERO to access V-Chip setup options π † To UNRATED √ ® To VIEW or BLOCK Press M ENU when done Directions to Block Unrated Programs Initial Setup Unrated Programs Unrated p...
Page 45 - is for VIOLENCE/FANTASY VIOLENCE
45 U.S. PARENTAL RATING SYSTEMSPrograms with the following ratings are appropriate for children. ❒ TV Y is Appropriate for All Children Programs are created for very young viewers and should be suitable for all ages, including children ages 2 - 6. ❒ TV Y7 is for Older Children Most parents would fin...
Page 46 - Directions to set US V-Chip Ratings; Setting US V-Chip Ratings
46 Initial Setup Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and press the π † or √ ® to move the cursor to the correct location. Press O K to turn the locking feature on or off. An item is locked if the icon appears instead of a “—”. For example. To blo...
Page 47 - Movies Ratings
47 Initial Setup ❒ NR – Not Rated This is a film which has no rating. In many cases these films were imported from countries which do not use the MPAA ratings system. Other NR films may be from amateur producers who didn’t intend to have their film widely released. NR (Not Rated) Programming may con...
Page 48 - Directions to set Canadian V-Chip Ratings
48 Press the M ENU button π † To V-CHIP √ ® To operate (lock icon appears) Press Z ERO to access V-Chip setup options π † To SET CANADIAN RATINGS ENG (for English) √ ® To enter ratings menu For example: To block viewing of programming rated 14+ and 18+: √ ® To the 18+ Column Press the O K button to ...
Page 49 - Set Lock Code
49 Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below. Press the M ENU button π † To SET LOCK CODE √ ® To operate (lock ...
Page 50 - Auto Demo
50 This function lets you preview the Dynamic Gamma demo. Press the M ENU button π † To AUTO DEMO √ ® To turn AUTO DEMO ON or OFF Note: • To stop auto demo, press the B ACK button. Initial Setup INITIAL SETUP SELECT OPERATE EXIT MENU NEXT PAGE PREVIOUS (4/5) AUTO TUNER SETUP CHANNEL SUMMARY V-CHIP S...
Page 51 - Closed Caption; Shows closed caption a priority for
51 Initial Setup Press the M ENU button π † To CLOSED CAPTION √ ® To enter π † To MODE √ ® To select CAPTION or TEXT in MODE π † To CAPTION or TEXT √ ® To select a caption (CC1 to CC4) or text channel (T1 to T4) Press the O K button to save Press the M ENU button when finished Many broadcasts now in...
Page 52 - Digital Manual Setting
52 • Closed caption subtitles are usually found on closed caption channel CC1. Some programs may include additional text information which is usually found on text channel T1. The other channels are available for future use. • Closed captioning may not work correctly if the signal being received is ...
Page 53 - Auto Shut Off; XDS ID; Noise Muting
53 Initial Setup This function automatically shuts off your TV when there is no signal from the channel the TV is on. Press the M ENU button π † To AUTO SHUT OFF √ ® To turn ON or OFF Press the M ENU button when finished • If the channel that you have on does not receive a signal for more than one m...
Page 54 - Front Panel Lock; V1 Smart Input
54 Initial Setup This allows you to lock the keys on the side of the TV, so that a child may not accidentally change your viewing preferences. Press the M ENU button π † To FRONT PANEL LOCK √ ® To turn ON or OFF Press the M ENU button when finished Front Panel Lock You can turn off this feature in t...
Page 55 - Video Input Label
55 Initial Setup This function is used to label video input connections for the onscreen displays. Press the M ENU button π † To VIDEO INPUT LABEL √ ® To enter π † To select the desired video input √ ® To select the desired preset input label (see chart below) Press the OK button to save Press the M...
Page 56 - Position Adjustment; Power Indicator
56 Initial Setup Position adjustment allows you to adjust the position of the picture on the screen vertically when the aspect is set to panorama, cinema or full. Press the M ENU button π † To POSITION ADJUSTMENT √ ® To enter π † √ ® To adjust the position Press the M ENU button to finish Notes: • T...
Page 57 - make sure that the TV volume level is low!; TV Speaker
57 Initial Setup If your TV is connected to a stereo system, you can turn off the TV speakers and listen to the audio through your stereo. Press the M ENU button π † To TV SPEAKER √ ® To turn the TV’s speakers ON or OFF Press the MENU button when finished Notes: • Before you turn the TV speaker sett...
Page 59 - Center CH Input
59 When you are using a surround system, you can substitute the speaker of this television for the center speaker of your surround system. Set CENTER CH INPUT to ON when you use the speaker as the center speaker of your surround system. The volume differs when the TV is being utilized as the Center ...
Page 60 - TINT; Picture Adjust; Picture Settings
60 Press the M ENU button π † To TINT, COLOR, PICTURE, BRIGHT or DETAIL √ ® To enter √ ® To adjust the setting π † To move to the next setting Press the M ENU button when finished These settings allow you to change and adjust the way the picture appears on your television. TINT Tint allows you to ad...
Page 61 - Digital Noise Clear
61 Picture Adjust With digital noise clear, this helps take our static or noise from a channel that may not be coming in clearly. Press the M ENU button π † To DIG. NOISE CLEAR √ ® To enter π † To select the mode LOW, HIGH, AUTO or OFF Press the M ENU button when finished Note: • "AUTO" can ...
Page 62 - Reset; Smart Picture
62 Reset Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig. noise clear, Color Management and Dynamic Gamma) at once to the default settings. Press the M ENU button π † To RESET √ ® To enter The onscreen menu disappears for a moment, and then the sett...
Page 63 - Sound Adjust; Sound Settings
63 These settings allow you to change and adjust the sound on your television. BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with the bass adjustment. TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio. BALANCE – Adjust the lev...
Page 64 - Set Clock; When you set the clock automatically, choose AUTO by pressing the; or
64 Clock/Timers Set Clock The set clock function is described on page 31 as the interactive plug-in menu. You can choose to set the clock automatically or manually. If you need to set the clock again, follow the steps below. Press the M ENU button π † To SET CLOCK √ ® To enter When you set the clock...
Page 66 - The following message will appear.; Lamp Timer Reset
66 The lamp replacement message will appear when you need to change the lamp. After you replace the lamp, you need to reset the timer which is built into your television. Press the M ENU button π † To LAMP TIMER RESET √ ® To Enter The following message will appear. Press the OK button while the abov...
Page 67 - Button Functions; Multi Screen Function
67 Button Functions Your television has two kinds of screen: TWIN (2 channels) and INDEX (12 channels). Multi Screen Function Note: After you press any multiscreen buttons, if you press the menu button, only the picture adjust screen will appear. Twin Activate the split-screen option by pressing T W...
Page 68 - Index; • It will only work in TWIN mode.; Freeze; will shift the channel.; Select; Pressing the F
68 Button Functions This allows you to quickly look at up to 12 channels at a time so that you can decide which one to watch. Notes: • Only RF input signal will be displayed.• You can watch the channel added in channel summary. See page 41. Index 1 5 9 2 6 10 3 7 11 4 8 12 You can exchange the chann...
Page 69 - Power; By every press of the I; Input
69 Button Functions Turns the TV on or off. Press the P OWER button Note: • After turning the power on, you can not turn the power off for about one minute. Power Use the number buttons on the remote control to move directly to a specific channel. For example, to move to channel 12: 0 (Zero) 1 (One)...
Page 70 - Return; Sound
70 Button Functions The R ETURN +/TV button has three functions: Return - Returns to the channel viewed just before the channel currently onscreen. Return+ - Lets you program a specific channel to return to while scanning through the channels using the CH+ and CH– buttons. TV - Returns to the TV mod...
Page 71 - Muting; Standard; By every press of the V; Video Status; Natural Cinema
71 Button Functions The M UTING button instantly turns the volume down completely when you press it. Press M UTING and the volume level will instantly go to zero. To restore the volume to its previous level, press M UTING again. Muting The V IDEO S TATUS button gives you a choice of four TV picture ...
Page 72 - Sleep Timer Message; Sleep Timer; the mode; MTS
72 Button Functions The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals of 15 minutes, for a total time of up to 180 minutes. Press the S LEEP button Sleep Timer Message 20 seconds before the automatic shutoff, this message will appear: You then have 20...
Page 73 - Display; Display
73 Button Functions The display screen shows the current status of timers, inputs and XDS ID. Press the D ISPLAY button The screen to the right shows the following information: • The current channel or AV input (Channel 05) • The current time (12:20 pm)• Sleep timer status/minutes remaining (The Sle...
Page 74 - Favorite; Delete the favorite channel
74 Button Functions The Favorite button allows you to select your favorite channels easily. First, you must register the channels that you like. See how to register below. Press the F AVORITE button The favorite channel list will appear. π † To select the channel you want to watch Press the O K butt...
Page 75 - Aspect
75 Button Functions This feature will help you adjust the picture you are watching to give you the best possible picture quality. REGULAR - The regular ratio is used when you want to watch a 4:3 broadcast or recorded program without modifying the original picture to fit the dimensions of your 16:9 s...
Page 76 - By pressing the A; Menu
76 Button Functions When you change the aspect ratios, it is different from their broadcast or recorded program. Aspect Ratios (Continued) Press the A SPECT button • By pressing the A SPECT button, you can change the size. ASPECT PANORAMA CINEMA FULL REGULAR ASPECT PANORAMA ZOOM CINEMA ZOOM FULL Not...
Page 77 - to; TV/CATV Slide Switch; button to turn the illumination on for 4 seconds.; Light
77 Button Functions Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to operate the television’s built-in tuner. Move the switch to CATV to operate a cable box. Note: • See page 33 for information on programming your remote for cable box operation. You c...
Page 78 - The onscreen will appear; Antenna Level; Digital Setup
78 Use this function when you are receiving a digital broadcast. Press the M ENU button π † To DIGITAL SETUP √ ® To enter The onscreen will appear Notes: • Software Update will only appear when the SD Card is inserted. • If you are watching an analog channel, you can still access the digital setup m...
Page 79 - Aspect Ratio; Digital Sound
79 Aspect Ratio You can select the aspect mode for ATSC from 4:3 or 16:9. Press the M ENU button π † To DIGITAL SETUP √ ® To enter π † To Aspect Ratio √ ® To select 4:3 or 16:9 Press the M ENU button when finished Notes: • Set the mode to 4:3 or 16:9 before you record a program using the ATSC MONITO...
Page 80 - Software Update; The application will perform; Cable Card Application
80 At first, insert the SD(Multi-media) card into the memory card slot. This function will appear only when you insert an SD Card. Press the M ENU button π † To DIGITAL SETUP √ ® To enter π † To Software Update √ ® To enter π † Checks the card if it needs an update or not Press the M ENU button when...
Page 81 - Digital Button Functions; Sub Channel; To watch digital channels
81 Digital Button Functions Sub Channel Digital CH D/A (Digital/Analog) The D/A button changes the analog and digital channel. Each time you press the D/A button, you can switch back and forth the analog and digital channels. Digital channels have a "D" in front of the channel number. Note: ...
Page 83 - Device; To select your device connecting with i.LINK
83 Device To operate, select a device. π † To select your device connecting with i.LINK Press the OK button Notes: • If you do not select the device, you cannot use the i.LINK timer functions. • When one device is selected and you select controller, you will move to the Controller onscreen. • The de...
Page 84 - Reservation
84 You can set the two timers: Record and view. The timer starts the recording or turns to the channel you set for it automatically. Press the T IMER button π † To New Reservation Press the O K button † To Timer Mode √ ® To select Rec or View † To Channel √ ® To select the channel you want to set th...
Page 85 - Timer Deletion
85 Timer Edit When you want to confirm the timer you set or edited, or delete the timer setting, use this function. Timer Edition Press the T IMER button π † To select the timer list you want to edit Press the O K button √ ® π † To change the setting you want to edit † To Set Timer Press the O K but...
Page 86 - Guide; Cancel the timer recording
86 You can view the program from the GUIDE. Notes:• The GUIDE function will only work when you are receiving digital programming only. • The GUIDE will not show the correct time and date if you have not performed the set clock function on your television. See page 64. Guide Digital Button Functions ...
Page 87 - OSD Information; Weak Signal; Invalid Signal; functions that you set, are still active.; No Program
87 OSD Information This OSD warning appears when the digital channel that you have selected is too weak to receive or no signal is being detected for that channel. Weak Signal Weak Signal 15 Invalid Signal If the TV channel you selected, or were watching is not receiving a signal, "NO PROGRAM...
Page 88 - Cable Card Information; Cable Card Connection; Note for inserting Cable Card:
88 Cable Card Information Cable card offers information when a cable card is inserted into the CABLE CARD slot on the back of the TV. Notes: • Please contact your local cable company regarding detailed information. Cable Card Connection ATSC /DIGITAL CABLE IN I CABLE CARD TV Rear Panel CABLE CARD No...
Page 89 - Troubleshooting; PROBLEMS
89 Troubleshooting There is no power There is no pictureor sound You cannot select a certain channel The power turns off by itself The clock is wrong The color quality is poor There are lines across the picture The picture is spotted There are double pictures (ghosts) Picture is snowy (image noise) ...
Page 90 - The following are not malfunctions.; • The lamp may make a noise when it blows, but this is not dangerous.
90 Troubleshooting The following are not malfunctions. • The television may make a creaking sound if the temperature of the room or the temperature inside the television changes. If there is no problem with the screen or sound, then there is no need to worry. • The lamp may make a noise when it blow...
Page 91 - Appendix; Changing the Lamp
91 Appendix Changing the Lamp WARNING! It is very important that you NEVER TOUCH THE GLASS SURFACE OF THE NEW LAMP. Touching the glass surface will deposit oils from your hand onto the lamp surface. When the lamp heats up to its operating temperature, the oil will cause a difference in temperature o...
Page 92 - Lamp Message; • This message will appear every time you; Replacement Lamp Kit; The replacement kit will include the following:
92 Appendix Lamp Message If this message appears when you turn the TV on, you need to replace the lamp. See page 97 on how to replace the lamp. Note: • This message will appear every time you turn on the TV when the lamp needs to be replaced. Press the OK button to make the message disappear, or rep...
Page 93 - How to Replace the Lamp; Please observe all
93 Appendix How to Replace the Lamp Please read these instructions fully before attempting to replace the lamp. If you feel unsure about replacing the lamp yourself, call a service technician. Please observe all safety warnings. 1) Turn off the television. Press the POWER button on the remote contro...
Page 94 - Do not forget to re-tighten the two screws.; Make sure the lamp sits securely and flat in the housing area.
94 Appendix WARNING! Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please read the warnings on page 91 again. Also, replace the lamp with part number TS-CL110U only! The television is designed to work specifically with this lamp. Lamps other than TS-CL110U may cause malfuncti...
Page 95 - Warning LED Messages; The LAMP/PROGRAM LED blinks; The POWER LED blinks; It may be a malfunction of the internal electrical circuits.; The POWER LED and LAMP/PROGRAM LED blink alternately; The inside temperature rises abnormally or the fan may be blocked.; The POWER LED and LAMP/PROGRAM LED blink rapidly simultaneously; into the lamp housing. Or it may be a lamp malfunction.
95 Warning LED Messages Appendix While the power is on, and there is a problem with the TV, the TV changes to warning mode and informs you of the problem using the LED as follows. Then, the power turns off automatically and performs the cooling for approximately 90 seconds. The LAMP/PROGRAM LED blin...
Page 97 - Specifications; Specifications subject to change without notice.
98 HD-ILA Device Projection Type Reception Format Reception Range Power Source Power Consumption Model NTSC, BTSC System (Multi-Channel Sound) ATSC Terrestrial, Digital Cable VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyperand Ultra bands (191 channel frequency synthesizer system) AC 120V, ...
