JVC AV-29BS26 - Manual

5 Remote control buttons and basic functions (continued) The following chart shows locations of functions in menus. In this manual, location of a function is described as follows: Note: Some functions have the 4th menus as the sub-menus. How to operate menus and menus locations To Operation Note Dis...

6 TV buttons and functions The illustrations shown below is for AV-21BS26 and AV-29SS26 only, which are used for explanation purpose.Your TV may not look exactly the same as illustrated. POWER TV/VIDEO MENU/OK CHANNEL VOLUME RV L/MONO IN(VIDEO-3) Front of the TV AV-29SS26 Rear of the TV AV-29SS26 PO...

7 2 Connecting the main plug to the AC outlet. Setting up your TV CAUTION • Turn off the equipment including the TV before connecting. VHF/UHF outdoor aerial 75-ohm coaxial cable (not supplied) 1 Connecting the aerial cable. 3 Inserting batteries into the remote control. Insert two batteries by foll...

8 5 Making the initial settings Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then operate the TV by following the steps below: • Press 5 / ∞ button to select your desired language*. • Press 5 / ∞ button to select your desired Teletext language group*. For details, see page 13...

9 COLOUR SYSTEM You can select the appropriate colour system when the picture is not clear or no colour appears.Press the COLOUR SYSTEM button to select a setting. To operate this function with a menu: For the colour system in each country or region, see the table below: PICTURE MODE You can choose ...

10 PICTURE SETTING You can adjust the desired picture setting when selecting USER in PICTURE MODE. 1 Select USER in PICTURE MODE under PICTURE menu. 2 Select PICTURE SETTING in PICTURE menu, then adjust the setting. CONTRAST 2 : Lower contrast 3 : Higher contrast BRIGHT 2 : Darker 3 : Brighter SHARP...

11 AI ECO SENSOR (ECO)/ECO MODE You can adjust TV screen contrast according to the brightness of your room.Press the ECO button to select the desired mode. OFF Cancel the function. MODE-1/ECO-1 Mild contrast (recommended.) MODE-2/ECO-2 Even contrast. DISPLAY (for AI ECO SENSOR only) Display the grap...

12 PIP Display the sub picture. To cancel, press the PIP button again. Notes: • You can hear the sound from the main picture only.• When main picture and sub picture are the same TV channel. Press SUB-P -/+ Main picture will be changed TV channel follow as sub picture. Press ( Input ) To change sub ...

14 SOUND SYSTEM You can select an appropriate sound system when abnormal sound occurs even when the picture appears normally.Press the SOUND SYSTEM button to select a setting. This function is not available in video mode.For the sound system in each country or region, see the table below: Basic sett...

15 CINEMA SURROUND You can enjoy an enhanced sound for wider audience.Press the CINEMA SURROUND button to select a setting. OFF Cancel the function. ON Listen to sound with wider audience effect. This function is not available when SOUND MODE is set to SOUND TURBO.To operate this function with a men...

16 DVD Menu AUTO SIGNAL DETECT When the DVD input signal is detected, the input mode will be changed to VIDEO-2 automatically. And when the DVD input signal is not detected, the input mode will be changed to RF previous input mode.Select AUTO SIGNAL DETECT in DVD MENU under FEATURES menu then choose...

17 Customized setting VNR You can reduce the picture noise.Select VNR in PICTURE menu, then choose a setting of VNR function. OFF VNR is turned off. AUTO Effect of VNR is automatically controlled. MIN Effect of VNR becomes minimum level. MAX Effect of VNR becomes maximum level. If you select MAX, th...

18 Customized setting (continued) DISPLAY You can display the programme number, video terminal number and PR list on the screen.Press the DISPLAY button to select the desired mode: Choose a TV channel or a VIDEO terminal. 1 Press the DISPLAY button to display the PR LIST. 2 Select a programme number...

19 To register the TV channels automatically (AUTO PROGRAM) You can register the TV channels into the TV’s channel list automatically. 1 Display the INSTALL menu. 2 Choose AUTO PROGRAM, then press the MENU/OK button. AUTO PROGRAM function starts, and the channels received are registered in the chann...

20 To add in the new channel (INSERT in the EDIT menu) You can add in new channels in the TV channel list as you like.You need to fi nd the “CH/CC” number for the TV channel. Find the “CH/CC” number corresponding to the channel number of the TV channel from “CH/CC number list” on page 21. 1 Display ...

21 TV channel presetting (continued) CH/CC number When you want to use the INSERT function o n p a g e 2 0 , f i n d t h e C H / C C n u m b e r corresponding to the channel number of the TV channel from this table. Channel No. Country US United States, Philippines, etc.. CCIR Middle East, Southeast...

22 V L R R L/MONO Y C B C R /V V S OVER L R /MONO OUTPUT VIDEO-1 COMPONENT (VIDEO-2) INPUT INPUT The illustrations shown in this section are for AV-21BS26 and AV-29SS26 only, which are used for explanation purpose. Your TV may not look exactly the same as illustrated. Before connecting • Read the ma...

23 Troubleshooting If a problem occurs when you are using the TV, check the below troubleshooting guide before calling for repair. • Colour patches appear at the corner of the screen • This may due to the magnetized device such as a speaker near to your TV. Keep the device apart from your TV. Altern...

© 2006 Victor Company of Japan, Limited 0406-FLE-JMT Speci fi cations TV RF systems B, G, I, D, K, M Colour systems PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band....