JVC AV-2983VE - Manual

5 Remote control buttons and basic functions (continued) The following chart shows locations of functions in menus. In this manual,location of a function is described as follows: Note: Some functions have the 4th menus as the sub-menus. To Display the MENU Display the topmenu Display the 2ndmenu Dis...

6 TV buttons and functions The illustrations shown below is for AV-2934WE andAV-2134YE only, which are used for explanation pur-pose.Your TV may not look exactly the same as illustrated. IN (VIDEO-3) V R MENU OK L/MONO CHANNEL VOLUME TV/VIDEO EXIT POWER ! 9 8 7 6 5 2 3 4 1 Front of the TV AV-2934WE ...

8 5 Making the initial settings Set up your TV by pressing any button except POWER button, then operate the TV menu by following the steps as below: • Press 5 / ∞ button to select your desiredlanguage*, then pressMENU/OK button. • Press 5 / ∞ button to select your desiredTeletext languagegroup. For ...

9 COLOUR SYSTEM You can select the appropriate colour system when the picture isnot clear or no colour appears.Press the COLOUR SYSTEM button to select a setting. To operate this function with a menu: For the colour system in each country or region, see the tablebelow: PICTURE MODE You can choose th...

10 Adjusting the picture – USER You can adjust the desired picture setting when selecting USERin PICTURE MODE. 1 Select the USER in PICTURE MODE under PICTURE menu. 2 Select the PICTURE SETTING in PICTURE menu, then adjustthe setting. CONTRAST 2 : Lower contrast 3 : Higher contrast BRIGHT 2 : Darker...

11 AI ECO SENSOR (ECO) You can adjust TV screen contrast according to the brightness ofyour room.Press the ECO button to select the desired mode. 1 Mild contrast (recommended). 2 Even contrast. OFF Cancel the function. To operate this function with a menu: You can display the graphic of AI ECO SENSO...

12 PIP You can display a sub picture on the screen.Press the PIP operation buttons to display and change the subpicture setting. PIP Display the sub picture.To cancel, press the PIP button again. Notes: • You can hear the sound from the main picture only.• Main picture and sub picture will use diffe...

13 Original features for picture (continued) Using the List mode You can store and recall the favorite teletext pages in memoryusing the colour buttons. 1 In TEXT mode, press the MODE button to enter the List mode. 2 Press a colour button, then press the number buttons to enterthe page number. 3 Pre...

14 SOUND SYSTEM You can select an appropriate sound system when abnormalsound occurs even when the picture appears normally.Press the SOUND SYSTEM button to select a setting. This function is not available in video mode.For the sound system in each country or region, see the tablebelow: Basic settin...

15 CINEMA SURROUND You can enjoy an enhanced sound for wider audience.Press the CINEMA SURROUND button to select a setting. OFF Cancel the function. LOW Listen to sound with less wider audience effect. HIGH Listen to sound with more wider audience effect. MONO Listen to mono sound with stereo effect...

16 To register the favorite channel You can register and recall 4 favorite channels by using thecolour buttons (red, green, yellow, blue). 1 In TV mode, select a TV channel (PR01-99) you desired to register. 2 Press and hold a colour button for 3 seconds or more.“FAVORITE CHANNEL ■ PROGRAMMED!” appe...

17 VNR You can reduce the noise.Select the VNR in the PICTURE FEATURES menu underPICTURE menu, then choose a setting of VNR function. OFF VNR is turned off. AUTO Effect of VNR is automatically controlled. MIN Effect of VNR becomes minimum level. MAX Effect of VNR becomes maximum level. If you select...

19 To register the TV channels automatically You can register the TV channels into the TV’s channel listautomatically. 1 Display the INSTALL menu. 2 Choose AUTO PROGRAM, then press the MENU/OK button.AUTO PROGRAM function starts, and the channels receivedare registered in the channel list (PR list) ...

22 The illustrations shown in this section are for AV-2934WE andAV-2134YE only, which are used for explanation purpose. YourTV may not look exactly the same as illustrated. Before connecting • Read the manuals provided with the devices for the proper connection. • Turn off all the devices including ...

23 Troubleshooting If a problem occurs when you are using the TV, check the belowtroubleshooting guide before calling for repair. • Deactivate the BLUE BACK function if it is turned on. • Choose the appropriate sound system. Refer to “SOUND SYSTEM” on page 14. • Check the aerial cable and its connec...

VICTOR COMPANY OF JAPAN, LIMITED © 2004 VICTOR COMPANY OF JAPAN, LIMITED 0504-FLE-JMT Specifications TV RF systems B, G, I, D, K, M Colour systems PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U)Receives cable channels in mid ba...