Juniper Networks J6300 - Manual

Juniper Networks J6300

Juniper Networks J6300 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
Page: / 7

Table of Contents:

  • Page 2 – J4300 and J6300 Ser vices Router PIM Installation Instructions; Tools and Par ts Required; J-series Services Router User Guide; POWER ON; Removing a PIM
  • Page 3 – Figure 1: Removing a PIM; Captive screws; LED blinks and then turns off.; Installing a PIM
  • Page 4 – System Basics Command Reference; Figure 2: Installing a PIM; List of Technical Publications
  • Page 5 – JUNOS References
  • Page 6 – Book; JUNOS Comprehensive Index and Glossar y; . Also provides a comprehensive; Hardware Documentation; For documentation issues, fill out the bug report form located at; Requesting Suppor t
  • Page 7 – Revision Histor y
Loading the manual

J4300 and J6300 Ser vices Router PIM
Installation Instructions

4 November 2004
Par t No: 530-011519-01
Revision 1

This document describes how to remove and replace a Physical Interface Module
(PIM) on Juniper Networks J4300 and J6300 Services Routers. For hardware
installation and basic troubleshooting procedures for J-series Services Routers, see
the

J-series Services Router User Guide

.

Contents

Tools and Parts Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Replacing a PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Removing a PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing a PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

List of Technical Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Requesting Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - J4300 and J6300 Ser vices Router PIM Installation Instructions; Tools and Par ts Required; J-series Services Router User Guide; POWER ON; Removing a PIM

J4300 and J6300 Ser vices Router PIM Installation Instructions Tools and Par ts Required To replace a component, you need the following tools and parts: Electrostatic bag or antistatic mat Electrostatic discharge (ESD) grounding wrist strap Phillips (+) screwdriver, number 2 Replacing a PIM Physical...

Page 3 - Figure 1: Removing a PIM; Captive screws; LED blinks and then turns off.; Installing a PIM

7. Loosen the captive screws on each side of the PIM faceplate. 8. Grasp the handles on each side of the PIM faceplate and slide the PIM out of the router. Place it in the electrostatic bag or on the antistatic mat. 9. If you are not reinstalling a PIM into the emptied slot, install a blank PIM pane...

Page 4 - System Basics Command Reference; Figure 2: Installing a PIM; List of Technical Publications

J4300 and J6300 Ser vices Router PIM Installation Instructions 4. Tighten the captive screws on each side of the PIM faceplate. 5. Insert the appropriate cables into the cable connectors on the PIM. 6. If necessary, arrange the cables to prevent them from dislodging or developing stress points: Secu...

Other Juniper Networks Models

All Juniper Networks Other