Page 2 - KEY TO SYMBOLS; Symbols
2 – English KEY TO SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the...
Page 3 - CONTENTS; Contents
English – 3 CONTENTS Contents Note the following before starting: Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment. So ...
Page 4 - SAFETY INSTRUCTIONS; Personal protective equipment; Throttle lock
4 – English SAFETY INSTRUCTIONS Personal protective equipment HELMET A helmet should be worn if the trees being cleared are taller than 2 m. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then ...
Page 5 - Cutting attachment guard; Quick release
English – 5 SAFETY INSTRUCTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Vibration damping system Your machine is equipped with a vibratio...
Page 6 - Cutting equipment; Locking nut; s safety equipment
6 – English SAFETY INSTRUCTIONS Cutting equipment Saw blades are intended for cutting fibrous types of wood. Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. Locking nut A locking nut is used to secure some types of cutting attachme...
Page 7 - Stop switch; Vibration damping system
English – 7 SAFETY INSTRUCTIONS • See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the cutting attachment stops and remains at a standstill. If the cutting attachment rotates with the throttle in the idle position then the carbu...
Page 9 - Filing the saw blade; Trimmer head
English – 9 SAFETY INSTRUCTIONS Filing the saw blade • See the cutting attachment packaging for correct sharpening instructions. A correctly filed blade is essential for working efficiently and to avoid unnecessary wear to the blade and clearing saw. • Make sure that the blade is well supported when...
Page 10 - General safety precautions; Starting; Transport and storage
10 – English SAFETY INSTRUCTIONS General safety precautions Starting • The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Obse...
Page 11 - General working instructions; Basic safety rules; Basic working techniques; Terms
English – 11 SAFETY INSTRUCTIONS General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose object...
Page 12 - The ABC of clearing; Forestry clearing using a saw blade
12 – English SAFETY INSTRUCTIONS The ABC of clearing • Always use the correct equipment. • Make sure the equipment is well adjusted. • Follow the safety precautions. • Organise your work carefully. • Always use full throttle when starting to cut with the blade. • Always use sharp blades. • Avoid sto...
Page 13 - Brush cutting with a saw blade; Grass clearing using a grass blade
English – 13 SAFETY INSTRUCTIONS • Large stems must be cut from two sides. First determine which direction the stem will fall. Make the first cut on the felling side. Then finish cutting the stem from the other side. Adjust the cutting pressure to match the size of the stem and the hardness of the w...
Page 14 - Grass trimming with a trimmer head
14 – English SAFETY INSTRUCTIONS Grass trimming with a trimmer head Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut. • The cord can easily remove grass an...
Page 17 - ASSEMBLY; Transport position, handlebar; Fitting blades and trimmer heads
English – 17 ASSEMBLY Assembling the handlebar and throttle • Unscrew the knob from the handlebar mounting. • Position the handlebar as shown. Fit the mounting components and tighten the knob lightly. • Fit the right handle to the handlebar using the screw, washer, sleeve and nut as shown. Tighten. ...
Page 20 - Safety release; Correct balance
20 – English ASSEMBLY Adjusting the harness and clearing saw Safety release At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness. Spreading the load on your shoulde...
Page 21 - FUEL HANDLING; Fuel; Gasoline; Mixing; Fuelling
English – 21 FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing sm...
Page 22 - STARTING AND STOPPING; Check before starting; Cold engine; Warm engine
22 – English STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...
Page 23 - Stopping
English – 23 STARTING AND STOPPING Stopping Stop the engine by switching off the ignition. Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (t...
Page 24 - MAINTENANCE; Carburettor; Function
24 – English MAINTENANCE Carburettor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaust...
Page 25 - High speed jet H; Muffler; Cooling system
English – 25 MAINTENANCE High speed jet H The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more t...
Page 26 - Air filter; Cleaning the air filter; Bevel gear
26 – English MAINTENANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. Clean the filter every 25 hours, or more regu...
Page 27 - Daily maintenance
English – 27 MAINTENANCE Filing the saw blade • See the cutting attachment packaging for correct sharpening instructions. A correctly filed blade is essential for working efficiently and to avoid unnecessary wear to the blade and clearing saw. • Make sure that the blade is well supported when you fi...
Page 28 - TECHNICAL DATA; Technical data
28 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...
Page 29 - FEDERAL EMISSION CONTROL WARRANTY STATEMENT
English – 29 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada...
Page 30 - Trimmy SII
1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII
