Jonsered BC2043 - Manual

English – 5 WHA T IS WHA T? What is what? 1 13 19 20 18 17 2 7 10 9 8 11 14 16 3 12 15 6 4 5 31 22 21 23 24 25 26 27 28 29 30 5 4 32 1 Trimmer head 2 Bevel gear 3 Grease filler cap, bevel gear 4 Cord cutter 5 Cutting attachment guard 6 Guard extension 7 Shaft 8 Handle adjustment 9 Throttle control 1...

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a vi...

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is po...

8 – English GENERAL SAFETY PRECA UTIONS Alw ays use the recommended guard for the cutting attachment you are using. See chapter on Technical data. Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. Usin...

English – 9 GENERAL SAFETY PRECAUTIONS Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage. Locking nu...

10 – English GENERAL SAFETY PRECAUTIONS Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents. Check the cutting attachment for damage or cracks. A damaged cutting attachm...

English – 11 ASSEMBLY Fitting the main body Connect the engine (A) to the tube (B) with four screws (C). Fitting the handlebar • Fit the handlebar in the handlebar clamp on the shaft using six screws. • Attach the cabling to the shaft with two cabling holders. • Put on the harness and hang the machi...

12 – English ASSEMBLY 9 Lap and fix the stop switch wires and connectors with clamp (I). 10 Refit the air filter cover. Assembling the cutting equipment Fitting the cord cutter and guard extension to the trimmer guard • Attach the cord cutter to the guard extension with screw and washer as shown. • ...

English – 13 ASSEMBLY Fitting other guards and cutting attachments • Fit the guard (A) to the gear housing using the support plate (M) and two screws (L). • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole ...

14 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...

English – 15 FUEL HANDLING Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mi...

16 – English STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

English – 17 STARTING AND STOPPING Warm engine Use the same starting procedure as for a cold engine but without setting the choke control in the choke position. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out th...

18 – English WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

English – 19 WORKING TECHNIQUES Grass clearing using a grass blade • Grass blades and grass cutters must not be used on woody stems. • A grass blade is used for all types of tall or coarse grass. • The grass is cut down with a sideways, swinging movement, where the movement from right-to-left is the...

English – 21 MAINTENANCE Carburettor Adjusting the idle speed (T) Check that the air filter is clean. When the idle speed is correct, the cutting attachment should not rotate. If adjustment is required, close (turn clockwise) the idle adjustment screw T, with the engine running, until the cutting at...

22 – English MAINTENANCE • Excessive fuel consumption. Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty. Cleaning the air filter Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refit...

English – 23 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensiv...

24 – English TECHNICAL DATA Technical data Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the highest level. The differ...

1 Poly Trim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10

Tap n’ Go 35 Spin "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm

"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm Tap n’Go 45 Spin

A 2,7 - 4,0 mm / .105 - .160" B 8 m / 26’ C 15 cm / 5.9" 1 2 3 5 6 7 9 4 8 6" 15 cm B C A Tap n’Go 55 Spin "Clic"

1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII