Johnson Controls TCGD30 - Manual
Johnson Controls TCGD30 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Johnson Controls Unitary Products; Physical and Electrical Data; MODEL; Unit
- Page 3 – System Charge for Various Matched Systems; Outdoor Unit
- Page 4 – COOLING CAPACITY - With Air Handler Coils
- Page 5 – COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
- Page 6 – COOLING CAPACITY - With High Efficiency Motor Furnaces
- Page 7 – COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)
- Page 8 – ACCESSORIES; Refer to Price Manual for specific model numbers.; OFF CYCLE TIMER DELAY; prevent rapid recycling of the compressor.; ROOM THERMOSTATS; TYPICAL INSTALLATION; UNIT
- Page 9 – COOLING PERFORMANCE DATA
TECHNICAL GUIDE
SPLIT-SYSTEM
AIR CONDITIONERS
13 SEER – R-410A – 3 PHASE
MODELS:
TCGD30 THRU 60
(2.5 THRU 5 NOMINAL TONS)
Due to continuous product improvement, specifications
are subject to change without notice.
Visit us on the web at www.york.com
Additional rating information can be found at
www.ahridirectory.org
LISTED
ISO 9001
Certified Quality
Management System
TECHNICAL
GUIDE
TECHNICAL
GUIDE
415571-UTG-C-0309
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
DESCRIPTION
The 13 SEER Series condensing unit is the outdoor part of a
versatile system of air conditioning. It is designed to be custom-
matched with one of UPG’s complete line of evaporator sec-
tions, with each serving a specific function. Matching Air Han-
dlers are available for upflow, downflow, or horizontal
applications to provide a complete system. Electric Heaters are
available, if required. Add-on coils are available for use with
upflow, downflow, or horizontal furnaces and air handlers.
WARRANTY
1-year limited parts warranty.
5-
year limited compressor warranty.
FEATURES
•
QUALITY CONDENSER COILS -
The coil is constructed of
aluminum microchannel tubing and enhanced aluminum fins
for increased efficiency and corrosion protection.
•
PROTECTED COMPRESSOR -
The compressor is inter-
nally protected against high pressure, temperature, and
externally by a factory installed high pressure switch. This is
accomplished by the simultaneous operation of high pres-
sure relief valve and a temperature sensor which protects the
compressor if undesirable operating conditions occur. A liq-
uid line filter-drier further protects the compressor.
•
DURABLE FINISH -
The cabinet is made of pre-painted
steel. The pre-treated galvanized steel provides a better
paint to steel bond, which resists corrosion and rust creep.
Special primer formulas and matted-textured finish insure
less fading when exposed to sunlight.
•
LOWER INSTALLED COST -
Installation time and costs are
reduced by easy power and control wiring connections.
Available in sweat connect models only. The unit contains
enough refrigerant for matching indoor coils and 15 feet of
interconnecting piping. The small base dimension means
less space is required on the ground or roof.
•
TOP DISCHARGE -
The warm air from the top mounted fan
is blown up away from the structure and any landscaping.
This allows compact location on multi-unit applications.
•
LOW OPERATING SOUND LEVEL -
The upward air flow
carries the normal operating noise away from the living area.
The rigid top panel effectively isolates any motor sound. Iso-
lator mounted compressor and the rippled fins of the con-
denser coil muffle the normal fan motor and compressor
operating sounds.
•
LOW MAINTENANCE -
Long life permanently lubricated
motor-bearings need no annual servicing.
•
EASY SERVICE ACCESS -
Fully exposed refrigerant con-
nections, and a single panel covering the electrical controls
make for easy servicing of the unit.
•
SECURED SERVICE VALVES -
Secured re-usable service
valves are provided on both the liquid and vapor sweat con-
nections for ease of evacuating and charging.
•
U.L. and C.U.L. listed -
approved for outdoor application.
•
Agency Listed
-
U.L. and C.U.L. listed - approved for out-
door application. The unit is certified in accordance with the
Unitary Small Equipment certification program, which is
based on ARI Standard 210/240.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
415571-UTG-C-0309 2 Johnson Controls Unitary Products All dimensions are in inches. They are subject to change with-out notice. Certified dimensions will be provided upon request. Physical and Electrical Data MODEL TCGD30 S43S1 TCGD36 S43S1 TCGD42 S43S1 TCGD48 S43S1 TCGD60 S43S1 TCGD30 S44S1 TCGD36 ...
415571-UTG-C-0309 Johnson Controls Unitary Products 3 PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing. 2. Verify the TXV and additional charge required for specific evaporator c...
415571-UTG-C-0309 4 Johnson Controls Unitary Products — = Not applicable. COOLING CAPACITY - With Air Handler Coils UNIT MODEL AIR HANDLER COIL MODEL 1 COOLING MODEL W RATED CFM NET MBH SEER EER TOTAL SENS. 13 SEER AC WITH MA TCGD30S4(3,4)S1 MA12B 17 FC/MC35B 1000 29.0 21.0 13.00 11.00 MA12B 17 FC/M...
