Johnson Controls TCGD18 THRU 60 - Manual
Johnson Controls TCGD18 THRU 60 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Johnson Controls Unitary Products; Physical and Electrical Data
- Page 3 – System Charge for Various Matched Systems; Outdoor Unit
- Page 4 – COOLING CAPACITY - With Air Handler Coils
- Page 6 – COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
- Page 7 – COOLING CAPACITY - With High Efficiency Motor Furnaces
- Page 8 – COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)
- Page 11 – ACCESSORIES; Refer to Price Manual for specific model numbers.; Off Cycle Timer Delay; vent rapid recycling of the compressor.; Hard Start Kit; provides increased starting torque for areas with low voltage.; Thermostats; - Compatible thermostat controls are available; TYPICAL INSTALLATION; Model
- Page 12 – COOLING PERFORMANCE DATA
SPLIT-SYSTEM
AIR CONDITIONERS
13 SEER – R-410A – 1 PHASE
MODELS:
TCGD18 THRU 60
(1.5 THRU 5 NOMINAL TONS)
Due to continuous product improvement, specifications are
subject to change without notice.
Visit us on the web at www.york.com
Additional rating information can be found at
www.ahridirectory.org
WARRANTY
Standard 5-year limited parts warranty.
Standard 5-year limited compressor warranty.
Extended 10-year limited parts warranty when product is
registered online within 90 days of purchase for replace-
ment or closing for new home construction.
LISTED
TECHNICAL
GUIDE
TECHNICAL
GUIDE
359319-BTG-G-0509
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
DESCRIPTION
The 13 SEER Series unit is the outdoor part of a versatile cli-
mate system. It is designed with a matching indoor coil compo-
nent from Johnson Controls Unitary Products. Available for
typical applications this climate system is supported with acces-
sories and documents to serve specific functions.
FEATURES
•
Quality Condenser Coils -
The coil is constructed of alumi-
num microchannel tubing and enhanced aluminum fins for
increased efficiency and corrosion protection.
•
Protected Compressor -
The compressor is internally pro-
tected against high pressure, temperature, and externally by
a factory installed high pressure switch. This is accomplished
by the simultaneous operation of high pressure relief valve
and a temperature sensor which protects the compressor if
undesirable operating conditions occur. A liquid line filter-
drier further protects the compressor.
•
Durable Finish -
The cabinet is made of pre-painted steel.
The pre-treated galvanized steel provides a better paint to
steel bond, which resists corrosion and rust creep. Special
primer formulas and matted-textured finish insure less fading
when exposed to sunlight.
•
Lower Installed Cost -
Installation time and costs are
reduced by easy power and control wiring connections.
Available in sweat connect models only. The unit contains
enough refrigerant for matching indoor coils and 15 feet of
interconnecting piping. The small base dimension means
less space is required on the ground or roof.
•
Top Discharge -
The warm air from the top mounted fan is
blown up away from the structure and any landscaping. This
allows compact location on multi-unit applications.
•
Low Operating Sound Level -
The upward air flow carries
the normal operating noise away from the living area. The
rigid top panel effectively isolates any motor sound. Isolator
mounted compressor and the rippled fins of the condenser
coil muffle the normal fan motor and compressor operating
sounds.
•
Low Maintenance -
Long life permanently lubricated motor-
bearings need no annual servicing.
•
Easy Service Access -
Fully exposed refrigerant connec-
tions, and a single panel covering the electrical controls
make for easy servicing of the unit.
•
Secured Service Valves -
Secured re-usable service valves
are provided on both the liquid and vapor sweat connections
for ease of evacuating and charging.
•
U.L. and C.U.L. listed -
approved for outdoor application.
•
Agency Listed
-
U.L. and C.U.L. listed - approved for out-
door application. The unit is certified in accordance with the
Unitary Small Equipment certification program, which is
based on ARI Standard 210/240.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
359319-BTG-G-0509 2 Johnson Controls Unitary Products All dimensions are in inches. They are subject to change with-out notice. Certified dimensions will be provided upon request. Physical and Electrical Data MODEL TCGD18 S41S1(H) TCGD24 S41S1 TCGD30 S41S1(H) TCGD36 S41S1(H) TCGD42 S41S1(H) TCGD48 S...
359319-BTG-G-0509 Johnson Controls Unitary Products 3 PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing. 2. Verify the TXV and additional charge required for specific evaporator c...
359319-BTG-G-0509 4 Johnson Controls Unitary Products COOLING CAPACITY - With Air Handler Coils UNIT MODEL AIR HANDLER COIL MODEL 1 COOLING MODEL W RATED CFM NET MBH SEER EER TOTAL SENS. 13 SEER AC WITH MA TCGD18S41S1(H) MA08B 17 FC/MC18B 600 17.5 12.9 13.00 11.00 TCGD24S41S1(H) MA08B 17 FC/MC36B 80...
