Page 2 - Safety information; General safety
Safety information It is most important that this instruction book should be retained withthe appliance for future reference. Should the appliance be sold ortransferred to another owner, or should you move house and leave theappliance, always ensure that the book is supplied with the appliance inord...
Page 4 - Child safety
• Plastic detergent dispensers should not remain in the drum during the drying cycle,as the plastic used is not designed towithstand the heat. If you wish to wash-through-to-dry you should use theconventional detergent dispenser drawer. • Never pull the power supply cable to remove the plug from the...
Page 5 - Contents; Operating instructions
Contents Operating instructions Safety information 2 General safety 2 Installation 3 Use 3 Child safety 4 Product description 6 Detergent dispenser drawer 7 Control panel 7 First use 9 Daily use 9 Load the laundry 9 Measure out the detergent 10 Select the required programme by turning theprogramme s...
Page 6 - Product description
Product description 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adjustable feet 1 2 3 5 4 6 6
Page 7 - Detergent dispenser drawer; Control panel
Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain removerused during the stain action phase (ifavailable). The prewash and soak detergent isadded at the beginning of the washprogramme. The stain remover is addedduring the stain action phase. Compartmen...
Page 9 - First use; Daily use; Load the laundry
The light End illuminates at the end of the washing cycle. First use • Ensure that the electrical and water connections comply with theinstallation instructions. • Remove the polystyrene block and any material from the drum. • Pour 2 litres of water into the main wash compartment of thedetergent dra...
Page 13 - Helpful hints and tips; Sorting out the laundry; Detergents and additives
Helpful hints and tips Sorting out the laundry Follow the wash code symbols on eachgarment label and the manufacturer’s washinginstructions. Sort the laundry as follows:whites, coloureds, synthetics, delicates,woollens. Before loading thelaundry Never wash whites and coloureds together.Whites may lo...
Page 15 - Washing Programmes
Washing Programmes Programme - Maximum and MinimumTemperature - Cycle Description - MaximumSpin Speed - Maximum Fabrics Load - Type ofLaundry Options Detergent Compartment COTTONS 90° - 60°Main wash - RinsesMaximum spin speed at 1200 rpmMax. load 5,5 kg - Reduced load 2,5 kg White cotton (heavily or...
Page 18 - Care and cleaning; Descaling; External cleaning
Care and cleaning Warning! You must DISCONNECT the appliance from the electricitysupply, before you can carry out anycleaning or maintenance work. Descaling The water we use normally contains lime. It isa good idea to periodically use a watersoftening powder in the machine. Do thisseparately from an...
Page 19 - Cleaning the pump
Cleaning the drawerrecess Having removed the drawer, use a small brushto clean the recess, ensuring that all washingpowder residue is removed from the upperand lower part of the recess. Replace the drawer and run the rinseprogramme without any clothes in the drum. Cleaning the pump The pump should b...
Page 22 - Installation; Unpacking
Installation Unpacking All transit bolts and packing must be removedbefore using the appliance.You are advised to keep all transit devices sothat they can be refitted if the machine everhas to be transported again.1. After removing all the packaging, carefully lay machine on it’s back to remove thep...
Page 23 - Positioning and levelling; Plumbing in
6. Fill the smaller upper hole and the two large ones with the corresponding plasticplug caps supplied in the bag containingthe instruction booklet. Positioning and levelling Install the machine on a flat hard floor. Makesure that air circulation around the machine isnot impeded by carpets, rugs etc...
Page 24 - Water inlet; Water drainage
Water inlet Warning! This appliance must be connected to a cold watersupply. The inlet hose is screwed to the back of theappliance.1. Set the hose correctly by loosening the ring nut. After positioning the inlet hose,be sure to tighten the ring nut again toprevent leaks. Always use the hosesupplied ...
Page 26 - Special conditions
Important! Before connecting up the machine to new pipework or to pipework thathas not been used for some time, run off areasonable amount of water to flush out anydebris that may have collected in the pipes. Special conditions If the floor is carpeted or covered withcrumbly or soft material, insert...
Page 27 - Electrical connection
SHOWER BATH BIDET WASHING MACHINE DISHWASHER RAINWATER ‘RUN-OFF’ SURFACE WATER DRAINS & SEWERS UNTREATED DISCHARGE RIVER RIVER FOUL DRAIN FOUL SEWERS SEWAGE TREATMENT WORKS TREATED DISCHRGE SINK TOILET Electrical connection Any electrical work required to install thisappliance should be carried ...
Page 28 - What to do if...
Important! Information on the electrical connection is given on therating plate on the inner edge of theappliance door. The appliance is supplied with a 13 amp plugfitted.In the event of having to change the fuse in theplug supplied, a 13 amp ASTA approved(BS1363/A) fuse must be used.Should the plug...
Page 31 - Repairs - After Sales Service
Problem Possible cause/Solution Spinning starts late or themachine does not spin: The electronic unbalance detection device has cut in because thelaundry is not evenly distributed in the drum. The laundry isredistributed by reverse rotation of the drum. This may happenseveral times before the unbala...
Page 32 - Spare parts; Environment concerns; Packaging materials
So that you always have these numbers athand, we recommend you to make a note ofthem here:• Mod....................................... • P.N.C..................................... • S.N......................................... Please retain your purchase receipt safely forthe service engineer to ver...
