John Deere RC1060 - Manual

John Deere RC1060

John Deere RC1060 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
Page: / 43

Table of Contents:

  • Page 2 – DEALER PREPARATION CHECK LIST; Frontier 10 Series Rotary Cutter; Introduction
  • Page 3 – Introduction 3; DANGER
  • Page 4 – Introduction; General Information
  • Page 5 – Safety 5; • Training; and safety decal information. (Replacement manuals and; • Preparation; Check that all hardware is properly installed.; SAFETY RULES
  • Page 6 – Safety; • Transportation; A minimum 20% of tractor and equipment weight; • Operation; being run over or crushed. Keep foldable ROPS
  • Page 7 – Safety 7
  • Page 8 – SAFETY and INSTRUCTIONAL DECALS; Replace Immediately if Damaged!; Safety and Instruction Decals
  • Page 9 – Safety and Instruction Decals 9
  • Page 10 – 0 Description; Major components; GENERAL DESCRIPTION
  • Page 11 – TECHNICAL DESCRIPTION; Description 11
  • Page 12 – 2 Preparation; • Preparing the Cutter; Perform the following procedures before operating the cutter:; Gearbox; PREPARATION; • Selecting Tractor PTO Speed
  • Page 13 – Preparation 13; • Installing Hitch Pin Bushings for Category 1 Quick Coupler Hitch; over hitch pin with cross hole as shown.; • Checking Driveline Shields; Check driveline shields by making sure they rotate freely.
  • Page 14 – ATTACHING
  • Page 15 – • Attaching PTO Driveline; • Checking Driveline/Cutter Clearance; Center link should be
  • Page 16 – • Detaching Cutter from Tractor; DETACHING
  • Page 17 – • Preparing Cutter for Operation; General Safety; OPERATION
  • Page 18 – • Adjusting Cutting Height and Angle; Using rockshaft control lever, position front
  • Page 19 – • Follow Safe Operating Procedures; Perform BEFORE EACH USE maintenance in the; • Keep Riders Off Machine
  • Page 20 – 0 Lubrication and Maintenance; LUBRICATION and MAINTENANCE; • Lubricating and Maintaining Machine Safely; • Maintenance Check List; • Maintenance After Each Use
  • Page 21 – • Lubrication Before Each Use; Driveline Universal Joints; Lubrication and Maintenance 21
  • Page 22 – SERVICE; • Practice Safe Service Procedures; Before servicing or adjusting machine connected to a tractor:; • Disassembling and Assembling Driveline Shields
  • Page 23 – • Removing and Installing Driveline-Slip Clutch; Install driveline in reverse order of removal.
  • Page 24 – • Removing and Installing Driveline-Shear Bolt; • Replacing Driveline Shear Bolt; If necessary remove sheared bolt with hammer; • Removing and Installing Tailwheel Support; • Checking Blade Wear; NOTE: Driveline shield pulled back for illustration
  • Page 25 – • Replacing Blades; • Direction of Blade Rotation
  • Page 26 – • Replacing Blade Pan; STORAGE
  • Page 27 – ASSEMBLY
  • Page 28 – • Assemble Hitch; Attach lift arm brace to frame using 1/2” x 1; • Install Tailwheel Support; (See Adjusting Cutting Height and Angle in
  • Page 29 – • Install Tailwheel; Remove snap ring and shear/retaining bolt from; • Fill Gearbox; After approximately 30 minutes of initial; and lock nuts. Insert bolts from inside out of rotary; Note: Driveline shield pulled back for
  • Page 31 – Final Inspection and Adjustments; MODIFY PTO DRIVELINE
  • Page 32 – METRIC; TORQUE SPECIFICATIONS; 2 Torque Specifi cations
  • Page 33 – Troubleshooting Guide 33; TROUBLESHOOTING GUIDE
  • Page 38 – PARTS
  • Page 42 – Chain Deflector Assembly
Loading the manual

ROTARY CUTTERS

O P E R A T O R ’ S M A N U A L

RC1048
RC1060
RC1072

ME300309 (Rev. 03/15/2007)

08/31/2009

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - DEALER PREPARATION CHECK LIST; Frontier 10 Series Rotary Cutter; Introduction

1. Implement is completely assembled. 2. Gearbox fi lled with oil and checked for possible leaks. (See page 29) 3. All fi ttings lubricated. (See page 20 - 21) 4. All shields in place and in good condition. 5. All fasteners torqued to specifi cations in Torque Chart. (See page 32) 6. Check PTO drive...

Page 3 - Introduction 3; DANGER

TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Frontier dealer. Read manual instructions and safety rules. Make sure all items on the Preparation Check List in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must c...

Page 4 - Introduction; General Information

TABLE OF CONTENTS Introduction..................................................................................................... 4Safety .......................................................................................................... 5-9Description .........................................

Other John Deere Models