John Deere OMPFP10808 - Manual

John Deere OMPFP10808

John Deere OMPFP10808 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
Page: / 52

Table of Contents:

  • Page 2 – Introduction; Foreword; Read The Guidance Manual
  • Page 3 – Contents; Safety; The right is reserved to make changes at any time without notice.
  • Page 4 – ii
  • Page 5 – Recognize Safety Information
  • Page 6 – Park Machine Safely
  • Page 7 – Practice Safe Maintenance
  • Page 8 – Keep Riders Off Machine
  • Page 9 – Getting Started; Theory of Operation; Software and Settings:; NOTE: When updating the receiver software, only
  • Page 11 – iGuide Activation; See GreenStar Display Operator Manual for activating.; Useful Buttons and Icons; NOTE: The machine receiver must be a StarFire iTC.
  • Page 12 – NOTE: The implement receiver must be a StarFire iTC.
  • Page 14 – Setup; To make iGuide function, the following criteria are required
  • Page 15 – Machine Setup
  • Page 16 – NOTE: Machine name must be defined in order to
  • Page 17 – Machine Offsets; Change Offsets; Enter machine offsets:
  • Page 18 – IMPORTANT: Offsets must be accurate because they
  • Page 19 – Implement Setup; NOTE: The implement setup should be verified
  • Page 20 – Press Implement 1 tab to get to the implement setup page.
  • Page 21 – Implement Offsets; —Used to define the actual implement; Control Point; —The location around which the implement; Value only needed if
  • Page 22 – —Used to enter implement width and; Defining Implement Width and Track Spacing.; —Used in guidance for how far each pass; Physical Width; —The actual width of the entire implement; NOTE: Physical Width is not used for Implement Guidance.
  • Page 23 – Implement GPS Offsets; Enter Implement GPS Offsets:; IMPORTANT: Drive a vehicle forward and have; NOTE: Minor adjustments to dimension B on the; NOTE: Measure from middle of vehicle receiver to
  • Page 24 – Receiver Installation
  • Page 25 – GPS Receiver Setup; NOTE: The implement receiver will detect its position
  • Page 26 – NOTE: Face receiver directly straight forward or backward.
  • Page 27 – Hours After Shutdown—; The use of this feature is
  • Page 28 – NOTE: When checking for bias, turn iGuide to “none”
  • Page 29 – Adjusting Lateral Offsets; NOTE: Do not measure the ends of the passes.; Implement GPS Lateral Offset Example—
  • Page 30 – Guidance Setup
  • Page 31 – Recommendation for use:; NOTE: You cannot navigate away from the iGuide; Adjusting the value manually:; Slope Compensation can be changed by three methods:
  • Page 33 – Calculating Slope Compensation Manually; Implement Error / Roll Angle = Slope Compensation; iGuide Sensitivity; iGuide Sensitivity affects how aggressively the system
  • Page 34 – Operation; Operation of iGuide
  • Page 35 – Blue line—recorded implement path
  • Page 36 – Integrating iGuide and iTEC Pro; NOTE: Please check the iGuide OM for a; NOTE: Please check the iGuide OM for a
  • Page 39 – Tuning Guide; Setting Up Vehicle Offsets; Vehicle Offsets
  • Page 40 – Setting Up Implement Offsets; Offset “E” is not required for iGuide.; Setting Up Implement GPS Offsets
  • Page 41 – Measuring in line dimension from receiver to receiver:; NOTE: When measuring distance between vehicle and
  • Page 42 – Tuning Slope Compensation; NOTE: If slope compensation value is above 4.00; Tuning iGuide Sensitivity; NOTE: For some platforms, such as four wheel drive
  • Page 43 – Troubleshooting; Troubleshooting Tips; Control Point—; NOTE: Do not wait until implement is aligned to
  • Page 44 – Valid Configuration; Will not work with 3­pt implements.
  • Page 45 – Specifications; Metric Bolt and Screw Torque Values
  • Page 46 – Unified Inch Bolt and Screw Torque Values
  • Page 47 – Index; APPENDIX; Index­1
  • Page 48 – Index­2
  • Page 49 – John Deere Service Keeps You On The Job; John Deere Parts; School is never out for John Deere service technicians.; Prompt Service
Loading the manual

iGuide

OPERATOR’S MANUAL

iGuide

OMPFP10808 ISSUE J0

(ENGLISH)

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,

birth defects, and other reproductive harm.

If this product contains a gasoline engine:

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

The State of California requires the above two warnings.

Additional Proposition 65 Warnings can be found in this manual.

John Deere Ag Management Solutions

(This manual replaces OMPC21775)

Printed in

U.S.A.

DCY

OMPFP10808

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Introduction; Foreword; Read The Guidance Manual

Introduction OUO6050,0000FB1 ­19­10AUG10­1/1 JS56696,0000218 ­19­10DEC08­1/1 JS56696,000039F ­19­23SEP09­1/1 www.StellarSupport.com NOTE: Product functionality may not be fully represented in this document due to product changes occurring after the time of printing. Read the latest Operator’s Manual...

Page 3 - Contents; Safety; The right is reserved to make changes at any time without notice.

Contents Page Safety .......................................................... 05­1 Getting Started Theory of Operation............................................ 10­1Making Implement Guidance Function ............... 10­2Accuracy ............................................................. 10­2i...

Page 4 - ii

Other John Deere Models