JennAir JDS1750FP0 - Installation Manual

5 Location Requirements IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial/rating plate. The model/serial/rating plate is located be...

6 Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. IMPORTANT: If installing a range hood or microwave hood combination above the cooking surface, follow the range hood or micr...

7 Venting Requirements IMPORTANT: This range must be exhausted outdoors unless you are using ductless venting. See the “Venting Methods” section. ■ Do not terminate the vent system in an attic or other enclosed area. ■ Use an approved vent cap for proper performance. If an alternate wall or roof cap...

8 Calculating Vent System Length IMPORTANT: This range is rated at 60 ft (18.3 m) of 6" (15.2 cm) or 30 ft (9.15 m) of 5" (12.7 cm) straight duct. To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. Vent Piece 5" (12.7 ...

9 Electrical Requirements – U.S.A. Only Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Prot...

10 Electrical Requirements – Canada Only Be sure that the electrical connection and wire size are adequate and in conformance with the CSA Standard C22.1, Canadian Electrical Code, Part 1 – latest edition, and all local codes and ordinances. A copy of the above code standards can be obtained from: C...

12 INSTALLATION INSTRUCTIONS Unpack Range 1. Remove shipping materials, tape and film from the range. Keep cardboard bottom under range. Do not dispose of anything until the installation is complete. 2. Remove oven racks and parts package from oven and shipping materials. 3. To remove cardboard bott...

13 4. Drill two 1/8" (3 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations. Rear position Front position Diagonal (2 options) 5. Using the two #10 x 1 5 ⁄ 8 " (4.1 cm) Phillips-head screws provided, mount anti-tip bracket to the ...

14 5. Align the template centerline with the centerline marked on the floor. Align the folded edge of the template against the rear wall. NOTE: Secure the template to the floor with tape. Install the Downdraft System Determine which venting method to use: floor or rear wall venting. Go to the sectio...

15 Floor Venting 1. Determine where within the template area that the vent will exit. Mark the vent hole for the type of venting you are using. IMPORTANT: Check for obstructions (plumbing, electrical, etc.) before marking the vent hole location. 2. Draw and cut the vent hole in the floor. 3. Install...

16 Make Gas Connection WARNING Explosion Hazard Use a new CSA International approved gas supply line.Install a shut-off valve.Securely tighten all gas connections.If connected to propane, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. Examples of a quali...

17 Install Blower Install Blower Cover 1. Locate blower motor cover. 2. Run the blower motor wires with strain relief through the small opening in the blower motor cover, starting from the inside and feeding out. Strain relief 3. Feed blower motor wire through opening and place the strain relief bra...

18 Connect Blower Electrical Parts 1. Locate the capacitor (in Blower Motor Kit). NOTE: The capacitor is supplied with a small harness that terminates in a two-pin connector as shown. Post 1 Post 2 2. Locate the capacitor storage tray in front of the blower bellow connection point in the lower right...

19 Verify Anti-Tip Bracket Is Installed and Engaged 1. Ensure range is in its final location. 2. Remove the front lower access panel. 3. Use a flashlight to look underneath the bottom of the range. 4. Visually check that the rear range foot is inserted into the slot of the anti-tip bracket. 5. Repla...

22 GAS CONVERSIONS Gas conversions from Natural gas to Propane gas or from Propane gas to Natural gas must be done by a qualified installer. WARNING Explosion Hazard Use a new CSA International approved gas supply line.Install a shut-off valve.Securely tighten all gas connections.If connected to pro...

23 6. Unscrew the metal cover and unscrew the blue regulator cap. Keep the washer in place. A B C A A. Metal cover B. Washer C. Blue regulator cap 7. Flip the blue regulator cap over and screw it back into the metal cover. A B 8. Screw the metal cover securely back into place. Do not overtighten. To...

24 Natural Gas Conversion WARNING Tip Over Hazard A child or adult can tip the range and be killed.Install anti-tip bracket to floor or wall per installation instructions.Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.Re-engage anti-tip bracket if range is moved.D...

25 4. Apply masking tape to the end of a 9/32" (7 mm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. A B C D A. Igniter electr...

26 Adjust Flame Height Adjust Surface Burner Flame Adjust the height of top burner flames. The cooktop “low” burner flame should be a steady blue flame approximately 1/4" (6 mm) high. Propane gas flames have a slightly yellow tip. A B A. Low flame B. High flame To Adjust Standard Burner: The fla...