JennAir 6 918803 A - Manual
JennAir 6 918803 A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Drill holes in the; back; of the panel using the template provided. Follow the
- Page 5 – into the back of the wood panel.
- Page 6 – See Step 3B for Custom Handle Installation.; the dishwasher. You will need to purchase two 1⁄4 - 20 bolts that are; 1⁄2 inches long. These can be found at any local hardware store.; the front panel. Discard the two large square washers.; NOTE: The large square washer should NOT be used with a custom panel.
- Page 7 – Step 4: Mounting the Custom Panel to the Dishwasher.
- Page 9 – Instructions pour panneaux personnalisés; Articles nécessaires :; Le panneau DOIT avoir une épaisseur de 3/4 po.; AVERTISSEMENT
- Page 10 – Étape 1 : Préparation du panneau personnalisé.; instructions fournies à la page suivante.; Perceuse
- Page 11 – B Préparation du panneau personnalisé sans le gabarit.
- Page 12 – Étape 2 : Installation des fixations de panneau.; droite et à gauche de la porte. Conservez ces vis.; er
- Page 13 – préalablement à l’arrière du panneau en bois.
- Page 14 – pouvez obtenir ces boulons dans votre quincaillerie locale.; panneau de façade. Jetez les deux grosses rondelles carrées.; Étape 3B : Montage des poignées personnalisées; l’arrière du panneau afin d’obtenir une adaptation parfaite.
- Page 15 – Étape 4 : Montage du panneau personnalisé sur le lave-vaisselle.; Vérifiez l’adaptation et l’aspect de l’ensemble.
- Page 16 – Étape 5 : Réglage de la tension du ressort de la porte.; Si la tension du ressort de la porte est insuffisante :
- Page 17 – Instrucciones del Panel Personalizado; Artículos Necesarios:; ADVERTENCIA
- Page 18 – Paso 1: Construcción del Panel Personalizado.; muestra en la figura siguiente.; parte trasera; del panel usando la plantilla provista. Siga las; Cinta Protectora
- Page 20 – Paso 2: Instalación de los Sujetadores del Panel.; Retire el panel delantero antiguo del lavavajillas.; do
- Page 22 – Ver Paso 3B para la instalación de la manija personalizada.; panel delantero. Descarte las dos arandelas grandes cuadradas.; Paso 3B: Montaje de las Manijas Personalizadas; del panel a fin de asegurar un buen ajuste.
- Page 23 – Paso 4: Montaje del Panel Personalizado en el Lavavajillas.; piriformes del panel interior de la puerta.
- Page 24 – Paso 5: Ajuste de la Tensión del Resorte de la Puerta.; Si la tensión del resorte de la puerta no es suficiente:
Custom Panel Instructions
Items you will need:
-
Custom Panel Door Front (max weight: 16 lbs)
o
Panel MUST be ¾ inch thick.
-
Tape Measure
-
Electric Drill
-
Torx (T-20) Head Screwdriver
-
1/8” Drill Bit
-
5/32” Drill Bit
-
Masking Tape
-
Safety Glasses
-
Original Installation Instructions
Additional items required if using handle provided with dishwasher:
-
¼” – 20 bolt, 2 ½” long
-
¼” Drill Bit
ALL ELECTRICAL WIRING, GROUNDING AND PLUMBING SHOULD BE DONE IN
ACCORDANCE WITH NATIONAL AND LOCAL CODES BY QUALIFIED INDIVIDUALS
CHECK LOCAL PLUMBING CODES
FOR APPROVED PLUMBING
PROCEDURES AND ACCESSORIES.
This appliance must be connected to a
grounded metal, permanent wiring system;
or an equipment-grounded conductor must
be run with the circuit conductors and con-
nected to the equipment-grounding terminal
or lead on the appliance.
This dishwasher is designed for operation on
an individual 120 VAC, 60 Hz grounded
electrical circuit. Use required fuse (15 amp)
or comparable circuit breaker. Two wire
with ground service to the dishwasher is
recommended for connection at the
terminal box and for grounding.
Part No. 6 918803 A
!"!$#%
"#&
$'$
'
(
%
$'
!"!$
)#&
*
$
(
+
-,
$
.
/
10 2
,
%3
$$,$
$
!"!$$
)45!$&$
#6
% ('
#&
/
$$
!
10 7
/
7
8
1"
$9%
&
!
(
.
5:
*0
%
$%
!
*+,
!!$3!
!"!$
$)
$
$!#&
;$
*+9
$.0 2
$%
! !
*+,$
$
$
,
3!
$9%
!
<
$
)$6
;
#%
50
7
/
',
8
"
9
&
!
=
<(
.
5:
*0
'LVFRQQHFWHOHFWULFDOSRZHUWR
GLVKZDVKHUEHIRUH\RXVWDUW
)DLOXUHWRIROORZWKLVZDUQLQJFRXOG
5HVXOWLQGHDWKRUVHULRXVLQMXU\
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Step 1: Construct the Custom Panel. 1.1 Ensure the custom panel is the same size as the panel shown in the figure below. 1.2 Drill holes in the back of the panel using the template provided. Follow the instructions on the front of the template. If the template is missing follow the instructions on f...
2.3 Remove the two panel fasteners from the face of the control panel on the inner door. 2.4 Screw each of the four panel fasteners into the four 5/32” pilot holes previously drilled into the back of the wood panel.
Step 3: Mounting the Handle (Handle Provided with Dishwasher). See Step 3B for Custom Handle Installation. NOTE: Use these instructions ONLY if you are using the same handle provided with the dishwasher. You will need to purchase two ¼ - 20 bolts that are 2 ½ inches long. These can be found at any l...
