Janus Pbx User Manual - Free PDF Download

Page 2 - If you have questions or problems, please

Table of Contents Section Page Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.C. Board Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programming Set-Up Methods . . . . . . . . . . . . . . . . . . . . . . . . . . Prog...

Page 3 - Installation

Installation Box-Less Style (PNB) 1. Mount phone on the car station. 2. Attach red lens cap and bezel to ¼” hole on car station. 3. Insert LED into lens cap and plug wire into P6. 4. 2 LED versions – Red LED goes to “Call in Progress” (P6) Green LED goes to “Alarm Received” (P5) 5. Attach emergency ...

Page 4 - PC Board Diagram

Page 5 - Programming Set-Up Methods; Method A: Calling the elevator phone to program it.; Programming Instructions

Programming Set-Up Methods There are two methods of setting up the hands-free elevator phone for programming. Select the one applicable to your situation as described below. NOTE: The telephone line provided must be a touch-tone line.The phone can be programmed at any location and then installed in ...

Page 6 - (enter the first phone number to be programmed); Optional Programming Instructions; To Eliminate Autodialing:; “Elevator call at the tone press; To Disable Voice Prompt Message and Delay Voice; “Elevator call at the tone

3. Enter # 0 (enter the first phone number to be programmed) * # . Listen for three beeps. EXAMPLE: # 0 5551212 * # . NOTE: If you are on a phone line that requires a “9” or another digit to call the answering service, enter a # after the 9 . This will insert a four second pause. EXAMPLE: # 09 # 555...

Page 7 - List of Commands for *Programming Mode; off/push again = turn off

To program location message, see step 8 in programming instructions. Enter # # and hang up. PURPOSE: To Enable Voice Prompt Message: (DEFAULT) To enable the voice prompt message to say: “Elevator call at the tone press one to talk, press two for location” . • Enter # 94851 or #9000000 and listen for...

Page 8 - power supply is needed or when to use a specific type of battery:; You will need a 9V battery or a 9-24VDC/12VAC power supply with; a need to call back to a specific elevator phone, or if all elevator

8 Auxiliary Outputs Information AUX1 (optional): The AUX1 output by default will not be active (open). If the user would like to activate this output they must program code: **44 • X *# - which controls the AUX1 behavior. The letter X on this code could be substituted by 0, 1, 2 or 3. • 0 = Disabled...

Page 9 - Troubleshooting Guide; only; Phone would not turn ʻONʼ

9 Troubleshooting Guide Always visually check the phone for loose or shorted wires, physically damaged, or missing components. The phone will not work on a Digital phone line. It will only work on an Analog phone line or an Analog port from a digital phone system. Problem: Phone would not turn ʻONʼ ...

Page 11 - Specifications; One shielded twisted pair communication cable; Phone Line Requirements:; Standard (analog) loop start voice grade; Operational Loop impedance:

11 Specifications Input Connections: One shielded twisted pair communication cable (shield should be grounded at the controller only). Phone Line Requirements: Standard (analog) loop start voice grade touch tone telephone line, PBX, or key system station Analog telephone line. Optional AC Adapter: 9...

Janus Pbx - User Manual

Table of Contents:

Was this manual helpful?

About this manual

Summary

Ask a question