Invacare WT 200 - Manual
Invacare WT 200 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FIGURE 1; Attaching Strap Assemblies to the Boom; Removing the Boom Bearing Retainer; Slide out the boom bearing retainer from the top of mast.
- Page 3 – FIGURE 2; Attaching the Walking Tutor to the Lift; Install the pivot assembly to the mast.
- Page 4 – FIGURE 3; Assembling the Armrest to Walking Tutor; Attach straps to walking tutor arm assembly (FIGURE 1 on page 2
- Page 5 – FIGURE 4; Adjusting the Armrest; Height; Angle; Loosen and pull out the armrest adjustment knob.; Depth; Slide the armrest assembly to the desired depth.; Hand Grip Distance; Slide the hand grip to the desired position.
- Page 6 – Using the Walking Tutor; FIGURE 5; Removing the Footplate; Fitting the Sling to a Patient; band against the patient.; FIGURE 6; Fitting the Sling to a Patient
- Page 7 – Lifting the Patient
1
For more information regarding Invacare products, parts, and services,
please visit www.invacare.com
Walking Tutor
Model No. WT 200
NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact
Carrier/Invacare for further instructions.
Safety Summary
To ensure the safe and proper installation of the WT200 walking tutor, these instructions
MUST be followed:
WARNING
DO NOT use this equipment without first reading and understanding this
instruction sheet. If you are unable to understand the warnings, cautions and
instructions, contact a healthcare professional, dealer or technical personnel if
applicable, before attempting to install this equipment - otherwise, injury or
damage may occur.
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
Assembling the Walking Tutor
Tools required:
• 9/16 Open End Wrench
• 16mm Box End Wrench
• 19mm Box End Wrench
• 13mm Socket Wrench
• 16mm Socket Wrench
• 18mm Socket Wrench
• 5mm Allen Key
• 6mm Allen Key
Attaching Strap Assemblies to the Boom
NOTE: For this procedure, refer to FIGURE 1 on page 2.
1. Remove the boom cover to expose the boom crossbar (Detail “C”).
2. Secure the strap assembly on the crossbar by placing the strap around crossbar and
inserting the buckles through the loop (Detail “A”).
Assembly, Installation and Operating Instructions
SAVE THESE INSTRUCTIONS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Walking Tutor 2 Part No 1141439 3. Ensure that the strap is up against the boom arm and is pulled down tight (Detail “B”). 4. Repeat Steps 1-3 for the other strap assembly. 5. Replace the boom cover. FIGURE 1 Attaching Strap Assemblies to the Boom Removing the Boom Bearing Retainer NOTE: For this pr...
Part No 1141439 3 Walking Tutor FIGURE 2 Removing the Boom Bearing Retainer Attaching the Walking Tutor to the Lift NOTE: For this procedure, refer to FIGURE 3 on page 4. 1. Install the pivot assembly to the mast. 2. Replace the boom bearing retainer. 3. Swing the boom back and push the bearing bloc...
Walking Tutor 4 Part No 1141439 FIGURE 3 Attaching the Walking Tutor to the Lift Assembling the Armrest to Walking Tutor NOTE: For this procedure, refer to FIGURE 1 on page 2 and FIGURE 4 on page 5. 1. Attach straps to walking tutor arm assembly (FIGURE 1 on page 2 ) . 2. Level the walking tutor arm...
