Invacare TR40R - Manual

Armrest Pad

Strap

Clamp

Bracket

Support Arm Bracket

(use as template)

F I G U R E 1 - I N S TA L L AT I O N

Tray Mounting Hardware

Assembly, Installation and Operating Instructions

Right Side Hardware

Left Side Hardware

Part Nos. TR40R

Part No. TR40L

6. Insert the support arm fully into the tray receptacle until it

cannot move further back.

7. Have the user sit in the wheelchair and position the tray

on the armrests, evenly spaced on both sides.

8. With a pen locate and mark the four (4) drill points on the

tray by using the support arm bracket as a template.

9. Using a 1/4" drillbit, drill four (4) holes corresponding to

the marks made with the pen.

NOTE: This product is designed to work with Invacare trays
LTACL, LTCCL, LTACCL and LTCCCL. The Invacare tray
mounting hardware can also be installed on other manufac-
turers' trays if the tray rim does not interfere with the opera-
tion of the tray support arm.

C A U T I O N

DO NOT drill too deep as this will render the
tray useless.

10. Counter-sink the holes to accomodate the flat screws

included in the kit.

11. Mount the tray using the flat screws, washers, and acorn

nuts with the hex key wrench provided. DO NOT over-
tighten screws.

12. With the user sitting in the wheelchair, adjust the tray to

the desired position and tighten knob on receptacle.

NOTE: The strap on the tray may be removed or wrapped
around armrest for additional support.

Tray

Support

Arm

Acorn Nut

Washer

Tray

Receptacle

Knob

Flat

Screws

Invacare Corporation

www.invacare.com

USA

Canada

One Invacare Way

5970 Chedworth Way

Invacare is a registered trademark of Invacare Corporation.

Elyria, Ohio USA

Mississauga, Ontario

©

1999 Invacare Corporation

44036-2125

L5R 3T9, Canada

800-333-6900

800-668-5324

Form No. 99-120 Part No. 0900121

Rev C (2) 12/99

SAVE THESE INSTRUCTIONS

NOTE: Check all parts for shipping damage before using.
In case of damage, do not use. Contact the dealer for fur-
ther instructions.

SAFETY SUMMARY

The following reccommendations are made for safe in-
stallation and use of the Tray Mounting Hardware:

GENERAL WARNINGS

DO NOT install this equipment without first
reading and understanding this instruction
sheet. If you are unable to understand
these Warnings, Cautions and Instructions,
contact a healthcare professional, dealer
or technical personnel if applicable be-
fore attempting to install this equipment -
otherwise, injury or damage may occur.

Consult a physician or therapist for ap-
propriate positioning of the tray relative
to the user.

Your therapist and physician should be con-
sulted if you have any questions regard-
ing individual limitations and needs.

The tray mounting hardware is available in two versions
TR40R: Right side hardware (shown)
TR40L: Left side hardware

Tools Required:
1/4-inch drillbit, a 82-degree counter sink drill, a hand drill,
a phillips screwdriver and a 1/2-inch open end wrench.

INSTALLATION (FIGURE 1)

1. Remove the armrest from the wheelchair. Refer to

the wheelchair owner's manual.

2. Using a Phillips screwdriver remove the armrest pad

from the armrest and set the screws aside.

3. Adjust the clamp brackets on the tray receptacle so

that one (1) of the four (4) holes on each clamp bracket
line up with one (1) armrest hole.

4. Secure the armrest pad and tray receptacle assem-

bly to the armrest with the previously removed screws
as shown in FIGURE 1.

5. Put both armrests on the wheelchair.