Page 2 - WARNING
Compass™SPT™ 2 Part No 1122134 WARNING A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS WHEELCHAIR. ALSO, A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES SPECIFICALLY INDICATED IN THE MANUAL. WHEELCHAIR USERS: DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERS...
Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS Compass™SPT™ 3 Part No 1122134 TABLE OF CONTENTS REGISTER YOUR PRODUCT ............................................................... 6SPECIAL NOTES ................................................................................ 9LABEL LOCATIONS .....................................
Page 6 - Complete and mail the form on the next page; protected as required by applicable laws and regulations.
TABLE OF CONTENTS Part No 1122134 6 Compass™SPT™ TABLE OF CONTENTS Quick-Release .......................................................................................................................................58 Permanent Axle .....................................................................
Page 7 - PRODUCT REGISTRATION FORM; Cut Along Line
Part No 1122134 7 Compass™SPT™ Name _______________________________________________________________ Address _____________________________________________________________ City ___________________ State/Province __________ Zip/Postal Code ________ Email ___________________________________ Phone No. __...
Page 8 - Fold
Compass™SPT™ 8 Part No 1122134 Fold here Fold here Cut Along Line Invacare Product Registration Form Please Seal with Tape Before Mailing
Page 9 - SPECIAL NOTES; NOTICE; THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO; SIGNAL WORD
SPECIAL NOTES Part No 1122134 9 Compass™SPT™ SPECIAL NOTES Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. Refer to the table below for definitions of the signal words. NOTICE THE INFORMATION CONTAINED IN THIS DO...
Page 10 - professional or assistant when in any tilt position.
SPECIAL NOTES Compass™SPT™ 10 Part No 1122134 WARNING Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.TO ...
Page 11 - LABEL LOCATIONS
LABEL LOCATIONS Part No 1122134 11 Compass™SPT™ LABEL LOCATIONS WARNING DO NOT OPERATE WITHOUT THE ANTI-TIP TUBES INSTALLED. REV. 5/98 P/N 60106X144 WARNING R E V. 1 0 / 9 8 10 2 6 9 6 0 Detent balls should extend beyond the diameter o f t h e a x l e bu s h i n g fo r a p o s i t i v e l o ck . Ke ...
Page 12 - FEATURES
FEATURES Compass™SPT™ 12 Part No 1122134 FEATURES Adjustable Arms (Optional) Adjustable Seat Depth Swingaway Footrest 6, 8-Inch Caster/ Fork Assembly Quick-Release Axles Anti-Tippers 12, 20, 22, 24-Inch Wheels Adjustable Angle/ Folding Back
Page 13 - TYPICAL PRODUCT PARAMETERS; INVACARE COMPASS SPT
TYPICAL PRODUCT PARAMETERS Part No 1122134 13 Compass™SPT™ TYPICAL PRODUCT PARAMETERS *NOTE: 18-inch x 18-inch seating, no footrests, no anti-tippers, in reverse configuration, with 22-inch wheels. INVACARE COMPASS SPT *OVERALL WIDTH: 27½ inches (seat width + 9½-inches) *OVERALL DEPTH: 33 to 39 inch...
Page 14 - SECTION 1—GENERAL GUIDELINES; Information for Healthcare Professionals/Assistants; for
SECTION 1—GENERAL GUIDELINES Compass™SPT™ 14 Part No 1122134 SECTION 1—GENERAL GUIDELINES Information for Healthcare Professionals/Assistants The Invacare Compass SPT wheelchair MUST be operated by a healthcare professional or assistant when in any tilt position. Stability The back height, seat dept...
Page 15 - Operating Information; or 120°) MUST be selected before repositioning
SECTION 1—GENERAL GUIDELINES Part No 1122134 15 Compass™SPT™ To maintain the stability of the wheelchair when moving the wheels to any position, the amount of tilt MUST be limited by adjusting the limit stops on the gas cylinders to prevent the wheelchair from tipping onto the anti-tippers. Operatin...
Page 16 - DO NOT stand on the frame of the wheelchair.; Weight Training; Invacare Compass SPT has a weight limit of 250 lbs.
SECTION 1—GENERAL GUIDELINES Compass™SPT™ 16 Part No 1122134 Wheel locks are not brakes. DO NOT attempt to stop a moving wheelchair with the wheel locks. Rear Wheel Configuration Only - DO NOT tip the wheelchair onto the wheels without assistance. Front Wheel Configuration Only - DO NOT tip the whee...
Page 17 - SECTION 2—SAFETY/HANDLING; Safety/Handling of Wheelchairs
SECTION 2—SAFETY/HANDLING Part No 1122134 17 Compass™SPT™ SECTION 2—SAFETY/HANDLING Safety/Handling of Wheelchairs “Safety and Handling” of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques in...
Page 18 - ments MUST be performed ONLY by a qualified technician.; Stability and Balance; Coping With Everyday Obstacles
SECTION 2—SAFETY/HANDLING Compass™SPT™ 18 Part No 1122134 WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees.The back height, seat depth, back angle, seating system, tilt angle, seat height, size/position...
Page 19 - use the spreader bar as a weight bearing support.; them up from the floor by reaching down between your knees.
SECTION 2—SAFETY/HANDLING Part No 1122134 19 Compass™SPT™ WARNING DO NOT attempt to lift the wheelchair by any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair.DO NOT use the spreader bar f...
Page 20 - gravity and may cause you to tip over.; Reaching and Leaning - Backwards; Tipping - Rear Wheel Configuration Only; DO NOT tip the wheelchair without assistance.
SECTION 2—SAFETY/HANDLING Compass™SPT™ 20 Part No 1122134 Reaching and Leaning - Backwards WARNING DO NOT lean over the top of the back upholstery. This will change your center of gravity and may cause you to tip over. NOTE: For this procedure, refer to FIGURE 2.3. Position wheelchair as close as po...
Page 21 - damage to the wheelchair.
SECTION 2—SAFETY/HANDLING Part No 1122134 21 Compass™SPT™ WARNING When lowering the casters of the wheelchair, DO NOT let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant and/or damage to the wheelchair. Roll the wheelchair forward and slowly lower t...
Page 22 - Roll the wheelchair backward and; SLOWLY; lower the wheelchair in one continuous; Tipping - Front Wheel Configuration Only; Position the wheelchair as close to the curb as possible.; Stairways - Rear Wheel Configuration Only
SECTION 2—SAFETY/HANDLING Compass™SPT™ 22 Part No 1122134 WARNING When lowering the front casters of the wheelchair, DO NOT let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant and/or damage to the wheelchair. Roll the wheelchair backward and SLOWLY ...
Page 23 - Stairways - Front Wheel Configuration Only; wheelchair has been rolled away from the stairway.
SECTION 2—SAFETY/HANDLING Part No 1122134 23 Compass™SPT™ WARNING Extreme caution is advised when it is necessary to move an occupied wheelchair up or down the stairs. Invacare recommends that, if possible, the user be removed from the wheelchair prior to moving. Invacare recommends using two assist...
Page 24 - Escalators; Transferring To and From Other Seats
SECTION 2—SAFETY/HANDLING Compass™SPT™ 24 Part No 1122134 Escalators WARNING DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur. Transferring To and From Other Seats WARNING BEFORE attempting to transfer in or out of the wheelchair, every precaution should b...
Page 25 - SECTION 3—SAFETY INSPECTION CHECKLIST; Safety Inspection Checklists; CAUTION
SECTION 3—SAFETY INSPECTION CHECKLIST Part No 1122134 25 Compass™SPT™ SECTION 3—SAFETY INSPECTION CHECKLIST NOTE: Every six months take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation...
Page 26 - Inspect/Adjust Weekly
SECTION 3—SAFETY INSPECTION CHECKLIST Compass™SPT™ 26 Part No 1122134 ❑ Ensure all caster/wheel/fork/headtube fasteners are secure. ❑ Ensure wheel locks do not interfere with tires when rolling. ❑ Ensure wheel lock pivot points are free of wear and looseness. ❑ Ensure wheel locks are easy to engage....
Page 27 - Inspect/Adjust Periodically; Troubleshooting - Mechanical; SOLUTIONS
SECTION 3—SAFETY INSPECTION CHECKLIST Part No 1122134 27 Compass™SPT™ Inspect/Adjust Periodically ❑ Inspect clothing guards for bent or protruding metal. ❑ Ensure that all fasteners on clothing guards are secure. ❑ Ensure arms are secure but easy to release and adjustment levers engage properly. ❑ E...
Page 28 - Maintenance/Transporting; operation. Refer to Adjusting the Quick-Release Axle on page 59.; Clean quick-release axles once a week with a Teflon; explode and cause bodily harm.; Make sure that all bolts are tight before operating wheelchair.; Replacing Wheel Handrim on page 60.
SECTION 3—SAFETY INSPECTION CHECKLIST Compass™SPT™ 28 Part No 1122134 Maintenance/Transporting WARNING After any adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. CAUTION DO NOT over tighten hardware attachi...
Page 29 - for a listing of the labels and their locations.; Transporting the Invacare Compass SPT
SECTION 3—SAFETY INSPECTION CHECKLIST Part No 1122134 29 Compass™SPT™ 9. Periodically check gas cylinders for oil leaks. If oil leak is detected, gas cylinder(s) should be replaced. 10. Replace any labels that are missing, worn or torn. Refer to Label Locations on page 11 for a listing of the labels...
Page 30 - SECTION 4—FRONT RIGGINGS; BEFORE using the wheelchair.; Installing/Removing Swingaway Front Riggings; Repeat STEPS 1-3 for opposite side of; Removing; Pull the front rigging release lever and
SECTION 4—FRONT RIGGINGS Compass™SPT™ 30 Part No 1122134 SECTION 4—FRONT RIGGINGS WARNING After making adjustments, always make sure that parts are properly tightened BEFORE using the wheelchair. Installing/Removing Swingaway Front Riggings CAUTION If front riggings are used, then the seat MUST be a...
Page 31 - Installing; Footrest; Adjusting Footrest Height; Height Adjustment Ranges; FOOTREST TYPE
SECTION 4—FRONT RIGGINGS Part No 1122134 31 Compass™SPT™ Installing/Removing Lift-Off Footrest NOTE: For this procedure, refer to FIGURE 4.2. Installing 1. Insert the footrest assembly mounting pins into the mounting tube of the wheelchair frame. 2. Repeat STEP 1 for the other footrest assembly. 3. ...
Page 32 - DO NOT overtighten socket bolt and; Adjusting Footrest Height -; Model PHW93 and PH904A Front Riggings; NOTE: Lay footrest on a flat surface to simplify procedure.
SECTION 4—FRONT RIGGINGS Compass™SPT™ 32 Part No 1122134 4. Securely tighten the hex screw and coved spacer. 5. Install the footrest assembly onto the wheelchair. Refer to Installing/Removing Swingaway Front Riggings on page 30. 6. Repeat STEPS 1-5 for the opposite side of the wheelchair, if necessa...
Page 33 - Installing Adjustable Angle Flip-up Footplate Hinge; Installing Adjustable Angle
SECTION 4—FRONT RIGGINGS Part No 1122134 33 Compass™SPT™ 3. Remove the hex bolt, coved washers and locknut that secure the lower footrest to the footrest support. 4. Reposition the lower footrest to the desired height. 5. Reinstall hex bolt, coved washers and locknut that secure lower footrest to fo...
Page 34 - Adjusting Adjustable Angle Flip-up Footplates; NOTE: Observe the angle of the footplate for reinstallation.; Angle Adjustment; Loosen, but DO NOT remove the adjustment screw in the half clamp.
SECTION 4—FRONT RIGGINGS Compass™SPT™ 34 Part No 1122134 Adjusting Adjustable Angle Flip-up Footplates WARNING When determining the angle of the footplates, make sure the rear of the footplates do not interfere with the movement of the front casters. Otherwise, injury or dam- age may occur. NOTE: Fo...
Page 35 - Disassembly; Remove the hex screw and coved; Reassembly; Composite/Articulating; Installing/Removing Elevating Legrests; Repeat STEPS 1-3 for the other elevating legrest assembly.
SECTION 4—FRONT RIGGINGS Part No 1122134 35 Compass™SPT™ Composite/Articulating Footplate Heel Loop Replacement NOTE: For this procedure, refer to FIGURE 4.8. Disassembly Composite. 1. Remove the hex screw and coved spacer that secure the lower footrest assembly to the swing away footrest assembly. ...
Page 36 - Replacing Sector Block; Raising/Lowering the Elevating Legrest; • Raising: Lift legrest assembly up to desired height.
SECTION 4—FRONT RIGGINGS Compass™SPT™ 36 Part No 1122134 Removing 1. Push the legrest release handle inward while rotating the elevating legrest outward. 2. Lift the legrest assembly out of the mounting tube of the wheelchair frame. 3. Repeat STEPS 1-2 for opposite side, if necessary. FIGURE 4.9 Rep...
Page 37 - Adjusting the Footplate Height; Adjusting Footplate Height and Calfpad Height/Depth
SECTION 4—FRONT RIGGINGS Part No 1122134 37 Compass™SPT™ Adjusting Footplate Height and Calfpad Height/Depth NOTE: For this procedure, refer to FIGURE 4.11. Adjusting the Footplate Height 1. Loosen locknut and washer securing the slide tube to the elevating legrest. 2. Reposition footplate to desire...
Page 38 - Composite; swing away footrest assembly.; Remove the hex screw and washer that
SECTION 4—FRONT RIGGINGS Compass™SPT™ 38 Part No 1122134 Composite/Articulating Footplate Heel Loop Replacement NOTE: For this procedure, refer to FIGURE 4.12. Disassembly Composite 1. Remove the hex screw and coved spacer that secure the lower footrest assembly to the swing away footrest assembly. ...
Page 39 - Secure the impact guards to the footrest frame.
SECTION 4—FRONT RIGGINGS Part No 1122134 39 Compass™SPT™ Installing Impact Guards/Calf Strap/H-Calf Strap NOTE: For this procedure, refer to FIGURE 4.14. NOTE: Impact guards are standard equipment on Model ST footrests. No assembly is required. 1. Remove impact guard/calf strap from packaged contain...
Page 40 - SECTION 5—ARMS; result in injury to the user or damage to the wheelchair.; Using/Adjusting Dual Point Arms; side rail to the up (horizontal) position as shown in Detail “A”.; side rail to the up (horizontal) position as shown in Detail “A”.; Adjusting Armrest; the arm to the up (horizontal) position as shown in Detail “A”.
SECTION 5—ARMS Compass™SPT™ 40 Part No 1122134 SECTION 5—ARMS WARNING After any adjustments, repair or service and before use, make sure all attachment hardware is tightened securely - otherwise, injury or damage may result.DO NOT attempt to lift or tilt a wheelchair by using any removable (detachab...
Page 41 - position as shown in Detail “A”.; Replacing Dual Point Arm Pad; Remove the mounting screws that
SECTION 5—ARMS Part No 1122134 41 Compass™SPT™ 3. Lock the armrest assembly by pressing the release lever into the down (vertical) position as shown in Detail “A”. 4. Pull up on the armrest assembly to ensure the armrest is locked in place. 5. Repeat STEPS 1-4 for opposite side of wheelchair, if nec...
Page 42 - with the existing hardware.
SECTION 5—ARMS Compass™SPT™ 42 Part No 1122134 2. Replace the existing clothing guard with the new clothing guard and securely tighten with the existing hardware. 3. Repeat STEPS 1-2 for the opposite side if necessary. Installing/Removing T-Arms NOTE: For this procedure, refer to FIGURE 5.3. Install...
Page 43 - Adjusting T-Arm Height; difficult to move the inside T-Arm post up and down.
SECTION 5—ARMS Part No 1122134 43 Compass™SPT™ Adjusting The T-Arms Adjusting T-Arm Height NOTE: For this procedure, refer to FIGURE 5.4. 1. Unlock the T-Arm by flipping the T-Arm release lever towards the inside of the wheelchair. NOTE: If necessary, pull the T-Arm release lever out and rotate 180°...
Page 44 - Adjusting T-Arm Width; Adjusting T-Arm Depth
SECTION 5—ARMS Compass™SPT™ 44 Part No 1122134 Adjusting T-Arm Width NOTE: For this procedure, refer to FIGURE 5.5. 1. Remove the two mounting screws that secure the arm pad to the arm tube. 2. Turn the arm pad around and reposition the arm pad on the arm tube. 3. Re-secure the arm pad to the arm tu...
Page 45 - Adjusting T-Arm Sockets; Remove the rear wheels from the wheelchair, if necessary. Refer to
SECTION 5—ARMS Part No 1122134 45 Compass™SPT™ Adjusting T-Arm Sockets NOTE: For this procedure, refer to FIGURE 5.7. NOTE: Perform this procedure if the T-Arm is too loose in the socket or does not easily slide UP and DOWN in the socket. 1. Remove the rear wheels from the wheelchair, if necessary. ...
Page 46 - Adjusting T-Arm Transfer Assists And/or Side Guards
SECTION 5—ARMS Compass™SPT™ 46 Part No 1122134 Adjusting T-Arm Transfer Assists And/or Side Guards NOTE: For this procedure, refer to FIGURE 5.8. 1. Remove the T-Arm from the wheelchair. Refer to Installing/Removing T-Arms on page 42. 2. Remove the two socket screws that secure the side guard to the...
Page 47 - Folding/Unfolding Back Assembly
SECTION 6—BACK/SEAT Part No 1122134 47 Compass™SPT™ SECTION 6—BACK/SEAT WARNING After adjustments and before use make sure all attaching hardware is securely tightened. Folding/Unfolding Back Assembly NOTE: For this procedure, refer to FIGURE 6.1. NOTE: When folding or unfolding the back, make sure ...
Page 48 - Installing and Removing a Seating System; Refer to the seating system Owner; Installing Stroller Handle; Remove the plug buttons from both back canes, if necessary.
SECTION 6—BACK/SEAT Compass™SPT™ 48 Part No 1122134 Installing and Removing a Seating System WARNING Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not...
Page 49 - Remove plug buttons from both back canes.; Press and hold the buttons on the quick-release pins; NOTE: Plug buttons not shown for clarity.
SECTION 6—BACK/SEAT Part No 1122134 49 Compass™SPT™ Installing/Removing/Adjusting the Adjustable Angle Stroller Handles NOTE: For this procedure, refer to FIGURE 6.3. Installing 1. Remove plug buttons from both back canes. 2. Slide the adjustable height stroller handle into the back canes. 3. Align ...
Page 50 - Adjusting/Replacing the Back Release Cord; Adjust the back release cord to the desired tension.; Replacing the Back Release Cord; Feed one end of the back release cord through the cord fastener.
SECTION 6—BACK/SEAT Compass™SPT™ 50 Part No 1122134 Adjusting/Replacing the Back Release Cord WARNING The back MUST be locked securely in place before using the wheelchair. NOTE: For this procedure, refer to FIGURE 6.4. NOTE: The back release cord may be adjusted to a tight or loose fit to meet the ...
Page 51 - Installing/Replacing Seat Positioning Straps; Position the seat positioning strap against the back plate.; Replacing; Discard existing seat positioning strap.
SECTION 6—BACK/SEAT Part No 1122134 51 Compass™SPT™ Installing/Replacing Seat Positioning Straps NOTE: For this procedure, refer to FIGURE 6.5. Installing 1. Remove the hex screw and locknut that secures the back cane to the back plate. 2. Position the seat positioning strap against the back plate. ...
Page 52 - Installing/Replacing Chest Positioning Straps; Discard existing chest positioning strap.
SECTION 6—BACK/SEAT Compass™SPT™ 52 Part No 1122134 Installing/Replacing Chest Positioning Straps NOTE: For this procedure, refer to FIGURE 6.6. Installing 1. Position the chest positioning strap to one of the holes on the back cane. NOTE: The standard recommended position for the chest positioning ...
Page 53 - SECTION 7—TILT; Place the wheelchair on a level surface.; Failure to observe this warning can result in serious injury.; Stand behind the wheelchair and grasp both back canes firmly.
SECTION 7—TILT Part No 1122134 53 Compass™SPT™ SECTION 7—TILT WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. Engaging Tilt-In-Space WARNING Both gas cylinders MUST be operational before u...
Page 54 - Adjusting Trigger Release Cables; 4 to 20-Inch Wide Wheelchairs; lock and hold its position, possibly causing injury.; assembly and try to tilt the wheelchair.
SECTION 7—TILT Compass™SPT™ 54 Part No 1122134 7. When the seat reaches the desired angle, slow let go of the trigger release levers. 8. To lower the seat parallel with the floor, reverse the above sections. FIGURE 7.1 Engaging Tilt-In-Space Adjusting Trigger Release Cables NOTE: For this procedure,...
Page 55 - 1 to 22-Inch Wide Wheelchairs; NOTE: If the cable is too loose, the gas cylinders will not work.
SECTION 7—TILT Part No 1122134 55 Compass™SPT™ • To Tighten - Turn the cable adjusting nut clockwise. DO NOT overtighten the cable adjusting nut (FIGURE 7.2). • To Loosen - Turn the cable adjusting nut counterclockwise (FIGURE 7.2). C. While holding the cable adjusting nut in place, tighten the cabl...
Page 57 - SECTION 8—WHEELS; Installing/Replacing Six or
SECTION 8—WHEELS Part No 1122134 57 Compass™SPT™ SECTION 8—WHEELS WARNING After adjustments and before use make sure all attaching hardware is securely tightened. Installing/Replacing Six or Eight-inch Caster/Fork NOTE: For this procedure, refer to FIGURE 8.1. Installing Caster/Fork 1. Remove the ca...
Page 58 - Installing/Removing Rear Wheels; through the center of the rear wheel.; Ensure quick release axle locking pins
SECTION 8—WHEELS Compass™SPT™ 58 Part No 1122134 Replacing/Repairing Caster Tire/Tube WARNING Replacement of caster tire or tube MUST be performed by a qualified technician. CAUTION As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced. ...
Page 59 - Permanent Axle; Installing/Removing Rear; Adjusting the Quick-Release Axle; Make sure detent pin and locking pins of; Adjusting the Quick-Release
SECTION 8—WHEELS Part No 1122134 59 Compass™SPT™ Permanent Axle NOTE: For this procedure, refer to FIGURE 8.3. NOTE: To remove rear wheels, reverse this procedure. 1. Remove the permanent axles from the packaged container. 2. Install permanent axle through the rear wheel and axle plate. 3. Securely ...
Page 60 - BEFORE operating the wheelchair.; Replacing Wheel Handrim
SECTION 8—WHEELS Compass™SPT™ 60 Part No 1122134 Replacing Wheel Handrim NOTE: For this procedure, refer to FIGURE 8.5. 1. Remove the wheel from the wheelchair. Refer to Installing/Removing Rear Wheels on page 58. 2. Remove the button screws that secure the existing handrim to the wheel. 3. Remove t...
Page 61 - SECTION 9—WHEEL LOCKS AND ANTI-TIPPERS; Wheel Lock Adjustment; correct wheel lock adjustment.
SECTION 9—WHEEL LOCKS AND ANTI-TIPPERS Part No 1122134 61 Compass™SPT™ SECTION 9—WHEEL LOCKS AND ANTI-TIPPERS WARNING After adjustments and before use make sure all attaching hardware is securely tightened. Wheel Lock Adjustment NOTE: For this procedure, refer to FIGURE 9.1. NOTE: Before adjusting t...
Page 62 - Installing Anti-Tippers
SECTION 9—WHEEL LOCKS AND ANTI-TIPPERS Compass™SPT™ 62 Part No 1122134 Installing/Adjusting Anti-Tippers NOTE: For this procedure, refer to FIGURE 9.2. NOTE: A 1½ to 2-inch clearance between the bottom of the anti-tipper wheels and the floor MUST be maintained at all times. Installing Anti-Tippers 1...
Page 63 - LIMITED WARRANTY
LIMITED WARRANTY Part No 1122134 63 Compass™SPT™ LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.This warranty is extended only to the original purchaser/user of our products.This warranty gives you s...