Page 2 - WARNING
P9000 ™ XDT 2 Part No. 1118386 WARNING A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS WHEELCHAIR. ALSO, A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES IN THE SERVICE MANUAL. WHEELCHAIR USERS: DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING (1) THE...
Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS Part No. 1118386 3 P9000 ™ XDT TABLE OF CONTENTS REGISTER YOUR PRODUCT ............................................................... 6SPECIAL NOTES ................................................................................ 9TYPICAL PRODUCT PARAMETERS ..........................
Page 6 - REGISTER YOUR PRODUCT; Complete and mail the form on the next page
REGISTER YOUR PRODUCT P9000 ™ XDT 6 Part No. 1118386 REGISTER YOUR PRODUCT The benefits of registering:1. Safeguard your investment.2. Ensure long term maintenance and servicing of your purchase.3. Receive updates with product information, maintenance tips, and industry news.4. Invacare can contact ...
Page 7 - PRODUCT REGISTRATION FORM
Name _______________________________________________________________ Address _____________________________________________________________ City ___________________ State/Province __________ Zip/Postal Code ________ Email ___________________________________ Phone No. _________________ Invacare Model ...
Page 9 - SPECIAL NOTES; NOTICE; THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO; signs of wear appear, belt MUST be replaced immediately.
SPECIAL NOTES Part No. 1118386 9 P9000 ™ XDT SPECIAL NOTES WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.WHEELCHAIR US...
Page 10 - TYPICAL PRODUCT PARAMETERS
TYPICAL PRODUCT PARAMETERS P9000 ™ XDT 10 Part No. 1118386 TYPICAL PRODUCT PARAMETERS *NOTE: Range will vary with battery conditions, surface, terrain and operating weight. **NOTE: Includes seating system and accessories. P9000 XDT SEAT WIDTH 18 inches SEAT DEPTH 16 or 18-inches (by extension) BACK ...
Page 11 - LABEL LOCATIONS; C A U T I O N
LABEL LOCATIONS Part No. 1118386 11 P9000 ™ XDT LABEL LOCATIONS Crossmember Lower Frame Tube WARNING DO NOT OPERATE WITHOUT THE ANTI-TIP TUBES INSTALLED. REV. 5/98 P/N 60106X144 Refer to Owner's Manualfor proper anti-tippersetting. 1085379 WARNING I M P O RTA N T NOTICE The wheel locks on this wheel...
Page 12 - SECTION 1—GENERAL GUIDELINES; injury or damage may occur.; Controller Settings/Repair or Service; CAUTION; Operating Information
SECTION 1—GENERAL GUIDELINES P9000 ™ XDT 12 Part No. 1118386 SECTION 1—GENERAL GUIDELINES WARNING This section contains important information for the safe operation and use of this product. DO NOT use this product or any available optional equipment without first completely reading and understanding...
Page 14 - Tire Pressure
SECTION 1—GENERAL GUIDELINES P9000 ™ XDT 14 Part No. 1118386 The seat positioning strap is a positioning belt only. It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, belt must be replaced immediately. Always v...
Page 15 - Charging Batteries; Grounding Instructions
SECTION 1—GENERAL GUIDELINES Part No. 1118386 15 P9000 ™ XDT Charging Batteries NEVER attempt to recharge the batteries by attaching cables directly to the battery terminals. DO NOT attempt to recharge the batteries and operate the wheelchair at the same time. DO NOT operate wheelchair with extensio...
Page 16 - Rain Test; Weight Training
SECTION 1—GENERAL GUIDELINES P9000 ™ XDT 16 Part No. 1118386 Rain Test Invacare has tested its power wheelchairs in accordance with ISO 7176 “Rain Test.” This provides the end user or his/her assistant sufficient time to remove his/her power wheelchair from a rain storm and retain wheelchair operati...
Page 17 - SECTION 2—EMI INFORMATION; CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION
SECTION 2—EMI INFORMATION Part No. 1118386 17 P9000 ™ XDT SECTION 2—EMI INFORMATION WARNING CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCHAIR.Electromagnetic Interference (EMI) From Radio Wave Source...
Page 19 - Stability and Balance; Coping With Everyday Obstacles
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1118386 19 P9000 ™ XDT SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS “Safety and Handling” of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques inv...
Page 20 - A Note to Wheelchair Assistants; DO NOT tip the wheelchair without assistance.
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS P9000 ™ XDT 20 Part No. 1118386 While the P9000 XDT is designed for use primarily in and around the home, the provider should determine whether this chair is suitable for the actual environment the chair will be used in. DO NOT go down ramp at full speed. Som...
Page 21 - in injury to the occupant.; using the wheelchair.
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1118386 21 P9000 ™ XDT WARNING DO NOT let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant. Roll the wheelchair forward and SLOWLY lower the wheelchair in one continuous movement. Push the wheelchair ...
Page 22 - ESCALATORS WARNING; Transferring to and From Other Seats; both casters parallel to the object you are transferring onto.
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS P9000 ™ XDT 22 Part No. 1118386 5. Using non-removable (non-detachable) parts of the wheelchair, lift the wheelchair off the ground and transfer the wheelchair up or down the stairs. 6. The wheelchair should not be lowered until the last stair has been negoti...
Page 23 - Percentage of Weight Distribution; attempting active use of the wheelchair.; Reaching, Leaning and
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1118386 23 P9000 ™ XDT Percentage of Weight Distribution WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees.Proper positioning is essential for your safet...
Page 24 - Reaching and Bending - Backward; gravity and may cause you to tip over.
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS P9000 ™ XDT 24 Part No. 1118386 FIGURE 3.2 Reaching, Leaning and Bending - Forward Reaching and Bending - Backward WARNING DO NOT lean over the top of the back upholstery. This will change your center of gravity and may cause you to tip over. NOTE: For this p...
Page 25 - Safety Inspection Checklists; wear and should be replaced as necessary.; Inspect/Adjust Initially; excessive
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1118386 25 P9000 ™ XDT SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING NOTE: Every six (6) months or as necessary take your wheelchair to a qualified dealer for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and ...
Page 26 - Inspect/Adjust Weekly
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING P9000 ™ XDT 26 Part No. 1118386 ❑ Seat and/or back upholstery have no rips and do not sag. Replace if necessary. Inspect/Adjust Weekly ❑ Seat is secured to wheelchair frame. ❑ Seat release latch is not worn and is functional. Replace if necessary. ❑ Inspec...
Page 27 - Troubleshooting - Mechanical
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1118386 27 P9000 ™ XDT ❑ Inspect charger AC power cord for damage. Replace if necessary. Troubleshooting - Mechanical Troubleshooting Guide Chair Veers Left/Right Sluggish Turn/Performance Casters Flutter Squeaks and Rattles Looseness In Chair Cha...
Page 28 - Checking Battery Charge Level
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING P9000 ™ XDT 28 Part No. 1118386 NOTE: For additional troubleshooting information and explanation of error codes, refer to the Electronics Manual (P/N 1110532) supplied with each wheelchair. Checking Battery Charge Level Joystick erratic or does not respond...
Page 29 - cumstances. IF UNQUALIFIED INDIVIDUALS PERFORM ANY WORK ON; SPJTMJoystick Switches and Indicators; Multi Function Charger Port; Speed Control switch
SECTION 5—WHEELCHAIR OPERATION Part No. 1118386 29 P9000 ™ XDT SECTION 5—WHEELCHAIR OPERATION WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Set-up/programming of the Electronic Cont...
Page 30 - Information Gauge Display
SECTION 5—WHEELCHAIR OPERATION P9000 ™ XDT 30 Part No. 1118386 FIGURE 5.1 SPJ™Joystick Switches and Indicators Information Gauge Display The Information Gauge Display is located on the front of the joystick housing. It provides the following information to the user on the status of the wheelchair - ...
Page 32 - Operating the Wheelchair; Turning the Power On/Off; Using the Horn
SECTION 5—WHEELCHAIR OPERATION P9000 ™ XDT 32 Part No. 1118386 Operating the Wheelchair NOTE: For this procedure, refer to FIGURE 5.2. Turning the Power On/Off 1. To turn the power ON, press the on/off button. NOTE: After turning power on, all indicators will light briefly and the display gauge will...
Page 34 - SECTION 6—FRONT RIGGINGS; switch on the joystick is in the OFF position.; Installing
SECTION 6—FRONT RIGGINGS P9000 ™ XDT 34 Part No. 1118386 SECTION 6—FRONT RIGGINGS WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or serv...
Page 35 - Removing; Adjusting the Footrest Height
SECTION 6—FRONT RIGGINGS Part No. 1118386 35 P9000 ™ XDT Removing 1. Push the footrest release lever inward. 2. Rotate swingaway footrest assembly outward. 3. Lift the swingaway footrest assembly off of the hinge pins. Using 1. To move the footrest out of the way without removing, push the footrest ...
Page 36 - Replacing the Heel Loop; Raising/Lowering the Legrest Assembly
SECTION 6—FRONT RIGGINGS P9000 ™ XDT 36 Part No. 1118386 Replacing the Heel Loop NOTE: For this procedure, refer to FIGURE 6.3. 1. Pull the cam lock lever up to the unlocked position. 2. Push in the release buttons and remove the lower footrest assembly. 3. Remove the mounting screw, spacer and lock...
Page 38 - SECTION 7—ARMS; on the joystick is in the off position.; Adjusting Armrest Height
SECTION 7—ARMS P9000 ™ XDT 38 Part No. 1118386 SECTION 7—ARMS WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or service verify that on/o...
Page 39 - Replacing Armrest Pad
SECTION 7—ARMS Part No. 1118386 39 P9000 ™ XDT Swing-Back Arms WARNING Make sure the armrest release lever is in the locked position before using the wheel- chair. NOTE: For this procedure, refer to FIGURE 7.2. 1. Unlock the swing-back arms by rotating the armrest release lever towards the outside o...
Page 40 - SECTION 8—SEAT AND BACK; Replacing the Seat Upholstery
SECTION 8—SEAT AND BACK P9000 ™ XDT 40 Part No. 1118386 SECTION 8—SEAT AND BACK WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or servic...
Page 41 - Replacing the Back Upholstery
SECTION 8—SEAT AND BACK Part No. 1118386 41 P9000 ™ XDT Replacing the Back Upholstery NOTE: For the following procedure, refer to FIGURE 8.2. 1. Flip swing back arms up and out of the way. Refer to Swing-Back Arms on page 39. 2. Remove the six (6) mounting screws and washers that secure the EXISTING...
Page 42 - Adjusting the Back Height
SECTION 8—SEAT AND BACK P9000 ™ XDT 42 Part No. 1118386 Adjusting the Back Height NOTE: For this procedure, refer to FIGURE 8.3. NOTE: Back canes must be adjusted to the same height. 1. Remove the two (2) mounting screws and locknuts that secure the two (2) back canes to the wheelchair frame. 2. Rep...
Page 43 - Replacing Seat Positioning Strap
SECTION 8—SEAT AND BACK Part No. 1118386 43 P9000 ™ XDT Replacing Seat Positioning Strap NOTE: For this procedure, refer to FIGURE 8.4. 1. If necessary, remove the seat cushion from the seat upholstery. 2. Remove the two (2) rear phillips screws and washers that secure the seat upholstery and seat p...
Page 44 - SECTION 9—JOYSTICK; Preparing the Joystick for Use
SECTION 9—JOYSTICK P9000 ™ XDT 44 Part No. 1118386 SECTION 9—JOYSTICK WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or service verify t...
Page 45 - Repositioning the Joystick
SECTION 9—JOYSTICK Part No. 1118386 45 P9000 ™ XDT Repositioning the Joystick NOTE: For this procedure, refer to FIGURE 9.2. NOTE: Before starting this procedure, it may be necessary to snip the tie-wraps (not shown in FIGURE 9.2) securing the joystick control cord to the wheelchair. Before snipping...
Page 46 - SECTION 10—CASTER; cracks and wear and should be replaced.; Adjusting Forks
SECTION 10—CASTER P9000 ™ XDT 46 Part No. 1118386 SECTION 10—CASTER WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or service verify tha...
Page 47 - SECTION 11—BATTERIES; When to Charge Batteries
SECTION 11—BATTERIES Part No. 1118386 47 P9000 ™ XDT SECTION 11—BATTERIES WARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.Before performing any maintenance, adjustment or service veri...
Page 49 - Connecting the Battery Charger; Replacing the Batteries; when working with batteries.; Recommended Battery Types; recommends their use as the power source for this unit.; wheelchair and give you unsatisfactory performance.
SECTION 11—BATTERIES Part No. 1118386 49 P9000 ™ XDT Connecting the Battery Charger NOTE: For this procedure, refer to FIGURE 11.2. 1. Attach the battery charger connector to the charger port on the joystick. 2. Plug the charger ’s AC power cord, or extension, into the grounded 120 VAC wall outlet. ...
Page 50 - Cleaning Battery Terminals; removed, NEVER look directly into them while charging batteries.; Removing/Installing the Battery Boxes
SECTION 11—BATTERIES P9000 ™ XDT 50 Part No. 1118386 2. Remove the existing batteries from the battery boxes. Refer to Installing/Removing Batteries Into/From Battery Boxes on page 52. 3. Clean the new battery terminals. 4. Install the new batteries into the battery boxes. Refer to Installing/Removi...
Page 51 - The battery box retaining strap MUST
SECTION 11—BATTERIES Part No. 1118386 51 P9000 ™ XDT 4. Place rear battery box onto the battery tray and connect the rear battery box to the front battery box. 5. Connect the front battery box to the controller. WARNING The battery box retaining strap MUST be fastened securely and adjusted prop- erl...
Page 52 - Installing/Removing Batteries Into/From Battery Boxes
SECTION 11—BATTERIES P9000 ™ XDT 52 Part No. 1118386 Installing/Removing Batteries Into/From Battery Boxes WARNING Make sure power to the wheelchair is OFF before performing this procedure.The use of rubber gloves and chemical goggles or face shields is recommended when working with batteries.Invaca...
Page 53 - Connecting Battery Cables; erwise, serious injury or damage may occur.
SECTION 11—BATTERIES Part No. 1118386 53 P9000 ™ XDT 1. If necessary, remove the battery boxes from the wheelchair. Refer to Removing/Installing the Battery Boxes on page 50. 2. Secure the battery lifting strap to battery terminal(s)/post(s). CAUTION Some battery manufacturers mold a carrying strap ...
Page 54 - Direct Mount Method
SECTION 11—BATTERIES P9000 ™ XDT 54 Part No. 1118386 FIGURE 11.6 Connecting Battery Cables Perform one (1) of the following methods for connecting the battery cable(s):• Dual U1 Batteries - Use direct mount method described on page 54. Refer to FIGURE 11.7. • Dual Group 22NF Batteries with Mounting ...
Page 55 - cable may result when installing battery terminal caps.
SECTION 11—BATTERIES Part No. 1118386 55 P9000 ™ XDT CAUTION When connecting the battery cables to the battery(ies), the battery cable(s) MUST be connected to the battery terminal(s)/post(s) as shown in Detail “A” or Detail “B” of FIGURE 11.7 (depending on battery type). Otherwise, damage to the bat...
Page 57 - Battery Clamp Method
SECTION 11—BATTERIES Part No. 1118386 57 P9000 ™ XDT 8. Install the battery box(es) into the wheelchair. Refer to Removing/Installing the Battery Boxes on page 50. NOTE: New battery(ies) MUST be fully charged before using, otherwise the life of the battery(ies) will be reduced. 9. If necessary, char...
Page 60 - Replacing Battery Box Retaining Strap; to hold battery boxes in place before using the wheelchair.; retaining strap buckle as shown in FIGURE 11.9.
SECTION 11—BATTERIES P9000 ™ XDT 60 Part No. 1118386 Replacing Battery Box Retaining Strap WARNING The battery box retaining strap MUST be fastened securely and adjusted properly to hold battery boxes in place before using the wheelchair. NOTE: For this procedure, refer to FIGURE 11.10. 1. Remove th...
Page 61 - DO NOT engage or disengage the clutches until the power is off.; FIGURE 12.1, the motors will be damaged and will need to be replaced.
SECTION 12—CLUTCH/MOTOR LOCK Part No. 1118386 61 P9000 ™ XDT SECTION 12—CLUTCH/MOTOR LOCK WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Engaging/Disengaging the Clutches WARNING DO NOT ...
Page 62 - SECTION 13—WHEEL LOCKS; Installing/Adjusting/Using the Wheel Locks
SECTION 13—WHEEL LOCKS P9000 ™ XDT 62 Part No. 1118386 SECTION 13—WHEEL LOCKS WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Installing/Adjusting/Using the Wheel Locks NOTE: For this pro...
Page 63 - Using; engaged - otherwise damage to the wheelchair may result.
SECTION 13—WHEEL LOCKS Part No. 1118386 63 P9000 ™ XDT FIGURE 13.1 Installing/Adjusting/Using the Wheel Locks Using The wheelchair is equipped with a pair of independently operated wheel locks located just in front of the rear wheels. 1. To engage the wheel locks, grip the handle and push forward to...
Page 64 - SECTION 14—ANTI-TIPPERS
SECTION 14—ANTI-TIPPERS P9000 ™ XDT 64 Part No. 1118386 SECTION 14—ANTI-TIPPERS WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Installing/Removing/Adjusting Anti-Tippers NOTE: For this p...
Page 66 - TRANSPORTING; are fully seated into the side frame H-blocks.
TRANSPORTING P9000 ™ XDT 66 Part No. 1118386 TRANSPORTING WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Transporting the P9000 XDT WARNING The weight of the wheelchair without the user ...
Page 68 - LIMITED WARRANTY
LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.This warranty is extended only to the original purchaser/user of our products.This warranty gives you specific legal rights and you may also have other ...
