Invacare Back Support - Manual

Page 2 - WARNING; N O T I C E; SAVE THESE INSTRUCTIONS; SPECIAL NOTES; PROCEDURE 1 - PREPARING; TABLE OF CONTENTS; PROCEDURE 4 - ADJUSTING THE; SPECIAL NOTES/TABLE OF CONTENTS

2 WARNING THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY AN AUTHORIZED DEALER OR QUALIFIED SERVICE TECHNICIAN. DO NOT INSTALL OR USE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND INSTRUCTIONS, CONTACT A HEALTHCARE ...

Page 3 - SAFETY SUMMARY; Adjusting the Mounting Hardware; STABILITY WARNINGS

3 SAFETY SUMMARY SAFETY SUMMARY SA F E TY S U MM A R Y NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction. INSTALLATION WARNINGS Stabilize from the ground up. A stable base, pelvis and footrests are requirements for anytorso position...

Page 4 - SEATING PRESSURE WARNING

4 SAFETY SUMMARY STABILITY WARNINGS (CONTINUED) ALWAYS make sure wheelchair is stable BEFORE reclining the back system. Rear wheels mayhave to be repositioned rearward depending on the degree of recline. ALWAYS ensurestability BEFORE using maximum amount of recline. TEST wheelchair BEFORE it is occu...

Page 5 - WA R N I N G; IMPORTANT INFORMATION; FIGURE 1 - INSTALLATION/ADJUSTMENT OVERVIEW; Adjusting the Depth Hardware

5 INSTALLATION/ADJUSTMENT OVERVIEW (FIGURE 1) WA R N I N G For proper installation of the Infinity Back and to reduce the risk of pressure sores, theadjustment procedures in this manual MUST be performed in the following order: 1. Adjusting the Mounting Hardware 2 . Adjusting the Hinge/Angle (DUALFL...

Page 6 - This Procedure includes the following:; Installing Cane Clamps; RIGHT

6 PROCEDURE 1 PREPARING WHEELCHAIR PR E P A R I N G W H EE L C H A I R This Procedure includes the following: Installing/Removing Cane Clamps Installing Inserts INSTALLING/REMOVING CANECLAMPS (FIGURE 1) NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. Insta...

Page 7 - PREPARING THE INFINITY BACK FOR INSTALLATION

7 This Procedure includes the following: Installing/Removing the Lateral Supports Installing/Removing Cushions Adjusting the Mounting Hardware PREPARING THE INFINITY BACK FOR INSTALLATION PROCEDURE 2 PR E PAR I NG T H E BACK INSTALLING/REMOVING THELATERAL SUPPORTS (FIGURE 1) NOTE: Refer to the INSTA...

Page 10 - PROCEDURE 3

1 0 INSTALLING/REMOVING THE INFINITY BACK INSTALLING/REMOVING THEINFINITY BACK (FIGURE 1) NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. Installing the Infinity Back 1. Ensure the four (4) cane clamps are securely installed on the wheelchair frame. Refer ...

Page 11 - FIGURE 1 - ADJUSTING CANE CLAMP

1 1 ADJUSTING THE INFINITY BACK PROCEDURE 4 ADJUSTING THE HINGE/ANGLE(DUALFLEX ONLY) NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. NOTE: The following procedures apply to the DualFlexONLY. If installing/adjusting a UniBack proceed to ADJUST-ING THE LATER...

Page 12 - LATERAL SUPPORTS in this procedure of the manual.; FIGURE 3 - ADJUSTING THE HINGE

1 2 ADJUSTING THE INFINITY BACK PROCEDURE 4 A D J U S T I NG Converting Fixed Angle Hinges to DynamicFlex Hinges (FIGURE 3) 1. Remove the four (4) short mounting screws securing the hinge to the back panels. NOTE: Save the short mounting screws for future conversionto fixed angle hinges. 2. Position...

Page 13 - ING THE WIDTH in this procedure of the manual.; FIGURE 5 - ADJUSTING THE LATERAL

1 3 PROCEDURE 4 ADJUSTING THE INFINITY BACK A D J U S T I NG 6. Slide one (1) lateral support to the desired location. 7. Visually inspect the adjustment slot to find proper lo- cation for the curved washer. 8. Remove one (1) mounting screw, tooth lock washer and curved washer. 9. Hold the mounting ...

Page 14 - LATERAL SUPPOR T CUSHION FOAM

1 4 PROCEDURE 5 FIGURE 1 - REMOVING/INSTALLING BACK CUSHION FOAM Top of Back Cover Back Cushion Foam Bottom Flap INSTALLING/REMOVINGCUSHION FOAM NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. Installing/Removing Back Cushion Foam(FIGURE 1) INSTALLING. 1. ...

Page 15 - INSPECTION; CLEANING; Cover

1 5 PROCEDURE 5 M A I N TE N A NC E MAINTENANCE Installing/Removing Adjustable PositioningPad (UNIBACK ONLY) (FIGURE 3) INSTALLING. 1. Lift the top flap up and pull the bottom flap down on the back cushion cover. 2. Grasp the cushion and pull upwards to remove the cushion from the back. 3. Align the...

Page 16 - LIMITED WARRANTY

Form No. 99-104 Part No. 1077719 Rev. A. (1)-3/99 Printed in U.S.A. INVACARE CORPORATION l ONE INVACARE WAY l P.O. Box 4028 l Elyria, Ohio 44036-2125 Phone 1-(800)-333-6900 l Technical Support 1-800-832-4707 INVACARE CANADA l 5970 Chedworth Way l Mississauga, Ontario, L5R 3T9 l Canada Phone (905) 89...

Invacare Back Support - Manual

Table of Contents:

Summary

Other Invacare Models