Invacare 6908A - Manual
Invacare 6908A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAUTION; guard to buckle or deform.; WARNING; footrest assembly. Failure to do so may result in serious injury.; INSTALLING SCISSOR MECHANISM GUARD (FIGURES 2 AND 3); NOTE; FIGURE 1 - INSTALLING FOOTREST GUARD; DETAIL B - Side View
- Page 3 – MANUFACTURED BEFORE; NOTE: Side panel not shown to show rivet; FIGURE 2 - INSTALLING THE SCISSOR MECHANISM GUARD
- Page 4 – DO NOT
Installing Cover Guards for MPR Clinical Recliners
Assembly, Installation and Operating Instructions
Kit # 1102816 for Model Nos. 6905A, 6907A, 6908A
NOTE: Check all parts for shipping damage, in case of damage, DO NOT use. Contact Carrier/Invacare
for further instructions.
SAVE THESE INSTRUCTIONS
SAFETY SUMMARY
To ensure the safe and proper installation and use of footrest and scissor mechanism guards,
these instructions MUST be followed:
GENERAL WARNING
DO NOT install this equipment without first reading and understanding this
instruction sheet and the Invacare Mobile Recliners Manual, part number
54000M107. If you are unable to understand the warnings, cautions and
instructions, contact a healthcare professional, dealer or technical personnel
if applicable, before attempting to install this equipment - otherwise, injury
or damage may occur.
INSTALLATION WARNING
After ANY adjustments, repair, or service and BEFORE use, make sure that all
attaching hardware is tightened securely.
INSTALLING FOOTREST GUARD AND SCISSOR
MECHANISM GUARD
FOOTREST GUARD (FIGURE 1)
NOTE
:
Right and left sides are determined from the users seated position.
1. Engage wheel locks.
2. Extend the footrest of the recliner.
3. Carefully tip the recliner onto the right side. Be sure there are no obstructions on or
around the floor before doing this.
4. Remove mounting bolt from support tube as shown in DETAIL A in FIGURE 1.
5. Install footrest guard around the footrest frame as shown in DETAIL A in FIGURE 1.
NOTE: Footrest guard needs to be folded in two (2) locations so it will wrap entirely around the upper
frame. Refer to the scored lines on the guard to determine where the folds should be.
6. Once folded, align the two (2) mounting holes of the footrest guard with the mounting
hole in the upper frame as shown in DETAIL A in FIGURE 1.
7. Using the mounting bolt, secure the footrest guard and upper frame to the support tube
as shown in DETAIL A in FIGURE 1.
1
Description
Quantity
Footrest Cover
2
Mechanism Cover
2
Tie Wrap
2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
8. With a tie wrap, secure the footrest guard to the upper side frame as shown in DETAIL B in FIGURE 1. NOTE : If necessary, trim excess tie wrap to prevent binding and pinching. CAUTION When installing tie-wrap, pull tie wrap tight but not too tight causing the guard to buckle or deform. WARNING ...
4. Remove four (4) existing bolts A, B, C and D from side frame as shown in FIGURE 3. 5. Position scissor mechanism guard against the side frame with the folded edge down. Refer to FIGURE 3. 6. Align holes of scissor mechanism guard with holes on side frame.7. Secure scissor mechanism guard to side ...
Invacare Corporation www.invacare.com USA One Invacare Way Invacare is a registered trademark of Elyria, Ohio USA Invacare Corporation. 44036-2125 Yes, you can. is a trademark of Invacare 800-333-6900 Corporation. © 2002 Invacare Corporation Part No. 1109697 Rev B - 7/02 FIGURE 3 - INSTALLING THE SC...
