Invacare 65500 - Manual

Invacare 65500

Invacare 65500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
Page: / 12

Table of Contents:

  • Page 2 – INSTALLING CANE KIT - Install NEW push handle.
  • Page 4 – INSTALLING BRAKE KIT - Proceed to STEP 3.
  • Page 12 – STINGRAY BRAKE PAD
Loading the manual

SAFETY SUMMARY (CONTINUED)

INSTALLATION WARNINGS

S P R I N T ( 6 5 4 0 0 ) a n d S P A R T A N ( 6 5 4 2 0 )
MODELS - The rollator height can ONLY be
adjusted where the push handle is textured
(FIGURE 4).

After installation and BEFORE use, ensure
that ALL attaching hardware is securely
t i g h t e n e d .

REPLACING SPRINT CANES AND
BRAKES (FIGURE 1)

1. Remove the EXISTING brake wire. Perform the fol-

lowing:

A. Loosen, but DO NOT remove the phillips screw

securing the brake wire to the brake wire clamp.

B. Remove the brake wire clamp and set aside.

C. Pull wire through the hole in the brake.

D. Remove the spring and set aside.

E. Pull wire through cable adjuster unit. If necessary,

loosen the cable adjuster unit locknut.

2. Pull brake cable UP to remove from side frame. If

necessary, cut ty-wrap.

3. Perform one (1) of the following:

INSTALLING CANE KIT - Remove EXISTING push
handle.

A. Rotate adjustment lever counterclockwise to

loosen. DO NOT remove.

B. Pull UP on the push handle to remove.

INSTALLING BRAKE KIT (BEFORE 3/7/00) - Re-
move EXISTING hand brake.

A. Remove the hex bolt, washer and locknut secur-

ing the hand brake to the push handle.

B. Remove the hand brake.

INSTALLING BRAKE KIT (AFTER 3/8/00) - Re-
move EXISTING hand brake.

A. Remove EXISTING hand grip from the push

handle and discard.

NOTE: Check ALL parts for shipping damage. If shipping
damage is noted, DO NOT use. Contact Carrier/Dealer for
further instruction.

SPARTAN - 65420

1076187

Cane Kit - Left

1076188

Cane Kit - Right

1076189

Brake Kit - Left (Before 3/7/00)

1076190

Brake Kit - Right (Before 3/7/00)

1096765

Brake Kit (After 3/8/00)

SPRINT - 65400

1076192

Cane Kit - Left

1076193

Cane Kit - Right

1076194

Brake Kit - Left (Before 3/7/00)

1076195

Brake Kit - Right (Before 3/7/00)

1096767

Brake Kit (After 3/8/00)

STINGRAY - 65500

1076182

Cane Kit

1076184

Brake Kit

STARGAZER - 65600

1076183

Cane Kit

1076184

Brake Kit

Note: Cane kits contain a push handle with hand grip, and
hand brake already attached.

SAVE THESE INSTRUCTIONS

SAFETY SUMMARY

The following recommendations are made for the safe
replacement of the Rollator Canes and Brakes:

GENERAL WARNINGS

DO NOT install this kit without first reading
and understanding this instruction sheet.
If you are unable to understand the
Warnings, Cautions and Instructions, con-
tact a healthcare professional, dealer or
technical personnel if applicable before
attempting to install this kit - otherwise,
injury or damage may occur.

A physical/occupational therapist should
assist in the placement and positioning of
the hand grips for maximum support and
correct brake activation. Be sure the
rollator is properly balanced BEFORE using.

Care should be taken to ensure that ALL
hand and height adjustments are secure,
and that casters and moving objects are
in good working order before using this
or any mobility aid.

PART

NUMBER

DESCRIPTION

Rollator Cane and Brake Replacement

Assembly, Installation and Operating Instructions

1

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - INSTALLING CANE KIT - Install NEW push handle.

2 B. Remove the phillips screw securing the EXIST- ING hand brake to the push handle. C. Pull the EXISTING hand brake off of the push handle. NOTE: Remove clamps/hardware located at the end ofthe NEW brake wire before performing the following steps. 4. Perform one (1) of the following: INSTALLING CA...

Page 4 - INSTALLING BRAKE KIT - Proceed to STEP 3.

4 REPLACING SPARTAN CANES ANDBRAKES Preparing Spartan for Brake Replacement(FIGURE 2) 1. Perform one (1) of the following: INSTALLING BRAKE KIT (BEFORE 3/7/00) - Re-move EXISTING hand brake. A. Remove the hex bolt, washer and locknut secur- ing the hand brake to the push handle. B. Remove the hand b...

Page 12 - STINGRAY BRAKE PAD

Invacare Corporation www.invacare.com USA Canada One Invacare Way 5970 Chedworth Way Invacare ® and "Yes, you can" are trademarks of Invacare Elyria, Ohio USA Mississauga, Ontario Corporation. 44036-2125 L5R 3T9, Canada © 2001 Invacare Corporation 800-333-6900 905-890-8838 Form No. 98-146 Pa...

Other Invacare Models

All Invacare Other