Invacare 1094952 - Manual
Invacare 1094952 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Space Saver Kit No. 1036793 Includes the following:; C A U T I O N
- Page 3 – Conventional Kit No. 1036794 includes the following:
- Page 4 – FIGURE 4 - REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT
- Page 5 – DETAIL “A” - TOP VIEW; LEFT; FIGURE 5 - REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT
- Page 6 – ARMREST OPERATION
- Page 7 – NOTES
SAVE THESE INSTRUCTIONS
NOTE: Check all parts for shipping damage before us-
ing. In case of damage, DO NOT use the equipment.
Contact the Dealer/Carrier for further instructions.
SAFETY SUMMARY
The following recommendations are made for the
safe use of the Space Saver/ Conventional Arm
Socket Assemblies:
GENERAL WARNING
DO NOT install or use this equipment with-
out first reading and understanding these
instructions. If you are unable to under-
stand the Warnings, Cautions or Instruc-
tions, contact a healthcare professional,
dealer or technical personnel before at-
tempting to install this equipment - other-
wise, injury or damage may occur.
INSTALLATION WARNING
After ANY adjustments, repair or service
and BEFORE use, make sure that all at-
taching hardware is tightened securely.
PURPOSE
To replace existing half-arms or install new FIXED or AD-
JUSTABLE arms on Invacare MVP and STYLE wheel-
chairs built after 10-10-92.
The Invacare MVP or STYLE can be fitted with Space
Saver or Conventional mounting brackets with either fixed
oradjustable arms. These arms can be used on all chairs
14 through 18 inches.
FRONT ARMREST SOCKET
REPLACEMENT/H-BLOCK
INSTALLATION (FIGURE 1)
1. Remove the locknut and screw securing the H-block
to the right and left front frames (FIGURE 1).
2. Remove the H-blocks.
NOTE: It may be necessary to reposition the wheel lock
assembly before/after installing the new front armrest sock-
ets/H-Blocks.
3. Position the NEW armrest socket/H-Block onto the
right and left front frames by performing one (1) of the
following:
NOTE: Armrest sockets/H-Block MUST be positioned
in the 1st or 2nd mounting hole on the right and left front
frames depending on the type of wheelchair.
A. MVP/STYLE 14 through 16 inches deep - Align
the mounting hole in the H-block with the first
mounting hole on front of chair.
B. ALL type wheelchairs 17 and 18-inch deep - Align
the mounting hole on the H-block with the second
mounting hole on front of chair.
FIGURE 1 - FRONT ARMREST SOCKET
REPLACEMANT/H-BLOCK INSTALLATION
1
Front Frames
Mounting
Holes
Armrest Socket/
H-Blocks
Mounting
Holes
Space Saver / Conventional Arm Socket Assemblies
Assembly, Installation and Operating Instructions
Kit Numbers 1036793, 1036794, 1094952, 1094953
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Rear Armrest Socket Right Chair Frame Right Outside Armrest Bracket Right Inside Armrest Bracket Locknuts Armrest Spacer Outside Armrest Bracket Inside Armrest Bracket Hex Screw Tube Support DETAIL “A” TOP VIEWS Hex Screws Left Outside Armrest Bracket Armrest Spacer Rear Armrest Socket Tube Suppor...
3 FIGURE 3 - REAR ARMREST SOCKET INSTALLATION - CONVENTIONAL ARMS Long Hex Screw Outside Armrest Bracket Inside Armrest Bracket Long Hex Screw Rear Armrest Socket Armrest Spacer Tube Support Left Outside Armrest Bracket Left Chair Frame Bracket Spacer Left Inside Armrest Bracket Locknuts Tube Suppor...
4 REAR ARMREST SOCKETINSTALLATION ON WHEELCHAIRSBUILT AFTER 7/00 Space Saver Armrest Sockets (FIGURE 4) Space Saver Kit No. 1094952 includes the following: DESCRIPTION QTY. Armrest Brackets 2 Front Armrest Sockets 2 Rear Armrest Sockets 2 Tube Supports 2 Nylon Washers 4 Long Hex Screw 2 Short Hex Sc...
