Invacare 1085144 - Manual

Invacare 1085144 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – C A U T I O N
Page 3 – Removing the Battery Connector (FIGURE 5); FIGURE 4 - REMOVING THE MOTOR SHROUD
Page 4 – FIGURE 6 - REMOVING CURRENT LIMIT
Page 5 – FIGURE 7 - INSTALLING THE BATTERY
Page 6 – FIGURE 8 - INSTALLING THE MOTOR SHROUD
Page 7 – FIGURE 9 - INSTALLING THE BATH LIFT INTO THE BATHTUB
Page 8 – LIMITED WARRANTY

Loading the manual

1. Secure the frame to the floor with the suction cups or by

standing on the frame base during removal of the seat.

2. Press the UP button on the pendant to raise the

seat all the way up (DETAIL "A").

3. Grasp the handgrip on the battery pack and pull

upwards to remove it from the motor shroud as
shown in DETAIL "B".

4. Press and hold the spring loaded chair release

button to release the seat (DETAIL "C").

5. While holding the button with one hand, grasp the

seat bottom firmly with your other hand.

6. Slide the seat up until the slide block disengages from

the groove in the frame as shown in FIGURE 1.

7. Grasp the handgrip on the battery pack and push

downwards to install onto the motor shroud.

8. Press the DOWN button on the pendant to lower

the bath lift to the lowest position (DETAIL "A").

9. If necessary, remove the bath lift frame from the

bathtub. Refer to REMOVING THE FRAME FROM
THE BATHTUB in this instruction sheet.

FIGURE 1 - REMOVING THE SEAT

Frame

Groove

Seat Bottom

Slide

Block

LIFT THE SEAT

STEPS 5-6

Down Button

Button

Pendant

DETAIL "A"

STEPS 1 AND 8

PULL UP TO REMOVE

PUSH DOWN TO

INSTALL

Battery Pack

DETAIL "B"

STEPS 2 AND 7

Motor

Shroud

Handgrip

Spring Loaded Chair Release Button

Recess

Seat

DETAIL "C"

STEP 4

NOTE: Check all parts for shipping damage. In case of dam-
age, DO NOT use. Contact your Dealer for further instruction.

SAFETY SUMMARY

The following recommendations are made for the
safe replacement of the PENDANT/CABLE/CUR-
RENT LIMIT DEVICE:

GENERAL WARNINGS

DO NOT install or use this equipment without
first reading and understanding this instruc-
tion sheet. If you are unable to understand
the Warnings, Cautions or Instructions in this
Instruction Sheet and in the Owner's Operat-
ing and Maintenance Manual (Part No.
1081003) provided with the Bath Lift, contact
a healthcare professional, dealer or techni-
cal personnel before attempting to install this
kit, otherwise, injury or damage may occur.

This kit MUST be installed by an Invacare
Dealer or technical personnel.

INSTALLATION WARNINGS

After ANY adjustments, repair or service and
BEFORE use, make sure all attaching hard-
ware is tightened securely - otherwise injury
or damage may occur.

Use proper lifting techniques to avoid in-
jury. Keep back straight and bend knees
when lifting components of the bath lift.

REPLACING THE PENDANT/CABLE/
CURRENT LIMIT DEVICE

NOTE: Refer to the INSTALLATION WARNINGS in the
SAFETY SUMMARY of this instruction sheet.

Removing the Seat (FIGURE 1)

WARNING

To prevent pinching injury between seat
back and motor shroud when removing/
installing the seat, DO NOT grasp seat any-
where other than at the recess at the top
(DETAIL "C"), the opening at the bottom of
the seat or the lip at the top of the seat.

To prevent frame from tipping when remov-
ing seat, either suction the frame to the floor
or place one foot on the frame base when
removing/installing the seat.

C A U T I O N

The bath lift seat MUST be removed from the
top of the lifting cycle, otherwise, damage
to the unit may occur.

DO NOT grasp seat by side flaps, otherwise
damage to the bath lift or the bathtub may
occur.

Reliant Bath Lift (RBL250)

Pendant/Cable/Current Limit Device Replacement Kit

Assembly, Installation and Operating Instructions

Kit No. 1085144

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - C A U T I O N

2 FIGURE 2 - REMOVING THE FRAME FROM THE BATHTUB TILT FRAME FORWARDS Frame Bathtub Suction Cup Loop Suction Cup Self-Locking Screws (STEP 2) Mounting Screw (STEP 2) Washer (STEP 2) Washers (STEP 2) Motor Shroud (STEP 3) FIGURE 3 - REMOVING THE MOTOR S H R O U D C A U T I O N The motor shroud is stil...

Page 3 - Removing the Battery Connector (FIGURE 5); FIGURE 4 - REMOVING THE MOTOR SHROUD

3 Removing the Battery Connector (FIGURE 5) 1. Remove the two (2) mounting screws and nuts securing the battery connector to the motor shroudas shown in FIGURE 5. 2. Carefully pull the battery connector away from the motor shroud. 3. Loosen, but do not remove the two (2) flat screws on the battery c...

Page 4 - FIGURE 6 - REMOVING CURRENT LIMIT

4 Installing the Battery Connector (FIGURE 7) C A U T I O N The BLUE (-) and YELLOW (+) wires MUSTbe installed properly, otherwise, seriousdamage to the electrical system of thebath lift may occur. 1. Position the BLUE (-) wire through the FRONT hole and the YELLOW (+) wire through the REAR holeas s...