Insignia NS-A700PF6 - Manual

NS-A700PF6 or NS-A700PF6-2 (LG)
1

Press the push button on the filter housing.

2

Gently pull the cartridge down and then pull it out

of the filter housing. You may need to lower or
remove the shelf below the cover.

3

Ensure that o-rings are present on the cartridge

and are seated into grooves.

4

Insert the new cartridge, pushing it in until it stops.

Push up firmly and close the cover.

5

Reset the filter change indicator in your refrigera-

tor, if applicable. (See “RESETTING YOUR FILTER
INDICATOR” on back page.)

Note: Run approximately 1.5 gallons of water through
the new filter before use.

NS-A8001F6 or NS-A8001F6-2 (Maytag, PuriClean II, Amana,
Sears/Kenmore, Whirlpool and Kitchenaid)
1

Twist the old filter counterclockwise and pull it out

of the receiver. The water automatically shuts off.

2

Push the new filter into the filter receiver until it

stops.

3

Turn the new filter clockwise until it stops.

4

Reset the filter change indicator in your refrigerator,

if applicable. (See “RESETTING YOUR FILTER
INDICATOR” on back page.)

Notes:
• Run approximately 1.5 gallons of water through the

new filter before use.

• Do not remove O-ring.

NS-LT600B-2 (LG and Kenmore)
1

Remove the old filter by rotating a half turn

counterclockwise, then pull it out. The water
automatically turns off.

2

If you have a Kenmore refrigerator, check if there is

a plastic or metal cap that covers the top of the old
filter. If there is, pull off the cap and attach it to
your new filter. If there is not, continue to step 3.

3

Align the top of your new filter with the receiver,

then push it in until it stops.

4

Rotate the filter a half turn clockwise to secure the

filter, then twist a little more to prevent leaks.

NS-DA2920 or NS-DA2920-2 (Samsung)
1

Remove the old filter by rotating it a 1/4 turn

counterclockwise, then pull it out.

2

Align the top of your new filter with the receiver,

then push it up until it stops.

3

Rotate the filter a 1/4 turn clockwise to secure the

filter.

BEFORE USING YOUR FILTER

If your refrigerator has a change filter indicator, reset it. See “Resetting your
filter indicator” for instructions.

Quick Setup Guide |

NS-A700PF6/NS-A700PF6-2/NS-A8001F6/NS-A8001F6-2/NS-LT600B-2/NS-DA2920/NS-DA2920-2

Refrigerator Filter

Before using your new product, please read these instructions to prevent any damage.

Congratulations on your purchase of one of the highest performing
water filters on the market today. Insignia filters use a high-grade
coconut carbon that has 50% more micro-pores than standard
carbon. They also use fewer high-compression binders, giving you the
best water filtration possible.

PACKAGE CONTENTS

• Refrigerator filter(s) (1 or 2 pack)
•

Quick Setup Guide

GENERAL INSTALLATION GUIDELINES

1

YOU MUST SOAK your new filter in water for 15 minutes prior to
installing it in your refrigerator. This is needed to remove air from
the carbon block.

2

It is normal for black carbon fines (particles) to appear on the outside

of your filter. This happens when the filter is jarred in shipping, it is
safe, simply wipe it off.

3

Connections on our filters are larger in size to prevent leakage. This
might require more hand leverage to install.

4

After installing, run about two to three gallons of water through your
refrigerator’s water dispenser to remove air and loose carbon pieces.
The water may be cloudy and sputter until the air is removed.

5

We apply a safe, NSF approved,

food grade silicone lubricant to our

filter connectors ( jelly like substance).

Installation:

*PUSH AND TURN HARD

To

remove

turn counter-clockwise

To

install

turn clockwise

Do not remove the O-ring

Filter receivers are designed to be flexible.

Don’t worry, they won’t break!

C

M

Y

CM

MY

CY

CMY

K

NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PM

NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PM

V3

FINAL

FOR PRINT