Ingersoll Rand ST600 - Manual

Page 2 - General Product Safety Information; WARNING; NOTICE; DANGER; NOTICE; Safety Symbol Identification

2 04662995_ed4 WARNING General Product Safety Information • Read and understand this manual before operating this starter. • It is your responsibility to make this safety information available to others that will operate this starter. • Failure to observe the following warnings could result in injur...

Page 3 - Placing Starter in Service; HOW TO ORDER A STARTER; B P

04662995_ed4 3 Placing Starter in Service Pinion Data Part Number Number of Teeth Blank DP/MOD PD PA Rotation OD inches mm inches mm ST600-13-31 12 12 6/8 2.000 50.80 20.0 R/L 2.250 57.15 ST600-13-51 15 15 6/8 2.500 63.50 20.0 R/L 2.750 69.85 ST600-13-83 12 12 3.5 Module 1.515 38.50 20.0 R/L 1.882 4...

Page 4 - Installation; General Information; Ingersoll Rand; Orientation of the Starter

4 04662995_ed4 Installation NOTICE For maximum performance, read this manual prior to installation or operation of Series ST600 Starters. General Information 1. This starter is designed for flange mounting at the inlet. The Flange Mounting Kit is required for installation. All Piping, hoses and valv...

Page 5 - Piping Diagram; PIPING DIAGRAM FOR A TYPICAL VEHICULAR INSTALLATION: PRE-ENGAGED

04662995_ed4 5 Piping Diagram (Dwg. TPE_1028_01) PIPING DIAGRAM FOR A TYPICAL STATIONARY INSTALLATION: PRE-ENGAGED PIPING DIAGRAM FOR A TYPICAL VEHICULAR INSTALLATION: PRE-ENGAGED SOLENOID VALVE - 120 VOLT*150BMP-2450 #4 HOSE (1/4) #4 HOSE (1/4) #4 HOSE (1/4) 1 1/2 HOSE RELAY VALVE 1 1/2*SRV150 JIC ...

Page 6 - Mounting Dimensions; ST600 PRE-ENGAGED MOUNTING DIMENSIONS

6 04662995_ed4 Mounting Dimensions (Dwg. TPE_1027) NOTES: 1. Please read instructions before attempting to reorient. 2. Starter weight is 39 Lbs. 3. Not to be used with natural gas. ARC STD 00 HALF 55 FULL 99 ST AR TER RA TIO PINION PINION ROT A TION “R” = RIGHT “L” = LEFT FLANGE 03 SAE 03 - STD I I...

Page 7 - ST600 Turbine Powered Starter - Section View

04662995_ed4 7 ST600 Turbine Powered Starter - Section View (Dwg.TPE_1029) SECTION A-A 24 23 22 21 19 17 18 16 13 15 14 10 9 8 7 12 11 6 5 4 3 2 1 20 A A

Page 8 - ST600 Turbine Powered Starter - Exploded Diagram

8 04662995_ed4 ST600 Turbine Powered Starter - Exploded Diagram (Dwg.TPE_1030)

Page 9 - ST600 Turbine Powered Starter - Parts List; Item Description

04662995_ed4 9 ST600 Turbine Powered Starter - Parts List Item Description Part Number Item Description Part Number 1 Screw ST700-737 18 Spring ST600-700 2 Spring D10-275 19 Spring Seat SS350-191 3 Deflector ST700-735 20 Screw (8) Y99-52 4 Exhaust Cap ST600-562 21 Drive Housing Assembly ST600-K300 5...

Page 10 - Maintenance; Lubrication; Disassembly; Assembly; General Instructions

10 04662995_ed4 Maintenance WARNING Always wear eye protection when operating or performing any maintenance on this starter. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this starter or before performing any maintenance o...

Page 11 - Assembly of the Starter; Troubleshooting Guide; Trouble

04662995_ed4 11 Assembly of the Starter 1. Place Motor Housing on a workbench, exhaust end up.2. Grasp Gear Package Assembly (10) and insert into Motor Housing. Rotate Gear Package to align Planet Gear Teeth with Ring Gear Teeth. 3. Place Wave Spring (9) onto Front Deflector (7).4. Insert Front Defl...

Page 12 - Parts and Maintenance

12 04662995_ed4 Parts and Maintenance NOTICE The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased motor performance, and increased maintenance, and may invalidate all warranties.Ingersoll Rand is not responsible for customer modification of motors fo...

Page 13 - Notes

Page 16 - Company

Ingersoll Rand ST600 - Manual

Table of Contents:

Summary

Other Ingersoll Rand Models