Ingersoll Rand PH10A-X-X - Manual
Ingersoll Rand PH10A-X-X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPERATING AND SAFETY PRECAUTIONS
- Page 4 – FLUID SECTION PARTS; FLUID SECTION DISASSEMBLY; evenly
- Page 5 – to threads at assembly.; ASSEMBLY NOTES; Torque Sequence
- Page 6 – Indicates parts included in 637338 Air Section Repair Kit.; AIR SECTION SERVICE; GENERAL SERVICE NOTES:; PILOT VALVE DISASSEMBLY
- Page 7 – Figure 3; MAJOR VALVE; PILOT; Figure 4; LUBRICATION / SEALANTS; Apply Loctite 271 to threads.; MAJOR VALVE DISASSEMBLY
- Page 8 – TROUBLE SHOOTING; Product discharged from exhaust outlet.; DIMENSIONAL DATA; Material Outlet; Figure 5
E
2010
CCN 99755480
(800) 276-4658
D
FAX (800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
OPERATOR’S MANUAL
PH10A-X-X
RELEASED:
7-7-00
REVISED:
10-15-10
(REV.
M
)
INCLUDING: OPERATION, INSTALLATION & SERVICE
1” HIGH PRESSURE DIAPHRAGM PUMP
3:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to “Model Description Chart” to match the pump material options.
637338 for air section repair (see page 6).
637339 for fluid section repair (models PH10A-XXX-XSX)(see page 4).
637339-1 for fluid section repair (models PH10A-XXX-XHX)(see page 4).
PUMP DATA
Models
see “Model Description Chart” for “-XXX”.
. . . . . . . . . . .
Pump Type
Metallic Air Operated, High Pressure,
. . . . . . . .
Double Diaphragm.
Material
see “Model Description Chart”.
. . . . . . . . . . .
Weight
94.73 lbs (42.97 kg)
. . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Air Inlet Pressure
100 p.s.i. (6.9 bar)
. . . . . . . . .
Maximum Outlet Pressure
300 p.s.i. (20.4 bar)
. . . . . . . . . .
Maximum Flow Rate (flooded inlet)
26 g.p.m. (98.4 l.p.m.)
. . .
Maximum Particle Size
1/8” dia. (3.2 mm)
. . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
Nitrile
10
_
to 180
_
F (-12
_
to 82
_
C)
. . . . . . . . . . . . . . . . .
PTFE
40
_
to 225
_
F (4
_
to 107
_
C)
. . . . . . . . . . . . . . . . .
Displacement / Cycle @ 100 p.s.i.
0.06 gal. (0.23 lit.)
. . . .
Dimensional Data
see page 8.
. . . . . . . . . . . . . . . .
Noise Level @ 70 p.s.i., 60 c.p.m.
84.5 db(A)
j
. . . . .
j
The pump sound pressure levels published here have been updated to an Equivalent Continuous
Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four micro-
phone locations.
NOTICE: All possible options are shown in the chart. However, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
PH10A-XSS-XXT
1” DIAPHRAGM PUMP
Figure 1
MODEL DESCRIPTION CHART
PH10 A - X S S - X X T
Seat Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Ball Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Fluid Caps & Manifold Material
S - Stainless Steel
Fluid Connection
A - 1 - 11-1/2 N.P.T.F. - 1
B - Rp 1 (1 - 11 BSP parallel)
Diaphragm Material
T PTFE
Hardware Material
S - Stainless Steel
Center Section Material
A - Aluminum
www.ingersollrandproducts.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PH10A-XXX-XXX (en) Page 2 of 8 OPERATING AND SAFETY PRECAUTIONS READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE. EXCESSIVE INLET AIR PRESSURE STATIC SPARK EXPLOSION HAZARD HAZARDOUS MATERIALS HAZARDOUS PRESSURE INJECTION HAZARD WARNING EXCESSIVE AIR PRESSURE. Can ca...
PH10A-XXX-XXX (en) Page 4 of 8 PARTS LIST / PH10A-XXX-XXX FLUID SECTION FLUID SECTION PARTS Item Description (size) Qty Part No. [Mtl] L Fluid Section Service Kit 637339-( ) V 1 Rod (1) 98724-1 [C] n 2 “O” Ring (3/32” x 3/4” o.d.) (1) Y330-113 [B] L 3 “O” Ring (3/32” x 11/16” o.d.) (4) Y328-112 [T] ...
Page 5 of 8 PH10A-XXX-XXX (en) PARTS LIST / PH10A-XXX-XXX FLUID SECTION . TORQUE REQUIREMENTS , NOTE: DO NOT OVERTIGHTEN FASTENERS. (14) Bolt, 49 - 52 ft lbs (66.4 - 70.5 Nm). (26) Bolts, 120 - 140 in. lbs (13.6 - 15.8 Nm). (29) Flange nuts, 280 - 300 in. lbs (31.6 - 33.9 Nm) tighten alternately and...
