Ingersoll Rand PE20X-XXX-XXX-XXXX - Manual
Ingersoll Rand PE20X-XXX-XXX-XXXX – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 6 – Without end of stroke feedback, solenoid control can only; figure 1
- Page 7 – figure 4; LUBRICATION / SEALANTS; “U” cups and mating parts.
- Page 8 – Set ring may need to be adjusted accordingly.; figure 5
- Page 9 – NOTE: ALL WIRING MUST COMPLYWITH ALL LOCAL; LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR); figure 8; LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR) - PINOUT DESCRIPTIONS; figure 7
- Page 10 – GENERAL DESCRIPTION; The ARO diaphragm pump cycle counter provides a closed; CYCLE COUNTER; figure 9
- Page 12 – OPERATION; The pump may be interfaced with a control device in the; Figure 1
- Page 13 – PORTED NO MOTOR OPTIONS
OPERATOR’S MANUAL
PE10X-XXX-XXX-XXXX
PE15X-XXX-XXX-XXXX
PE20X-XXX-XXX-XXXX
PE30X-XXX-XXX-XXXX
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED:
3-26-13
(REV. B)
ELECTRONIC INTERfACE
for Diaphragm Pumps
READ THIS MANUAL CAREfULLY BEfORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276
FAX (800) 892-6276
© 2013
CCN 46750816
www.ingersollrandproducts.com
PUMP DATA
PE10X-XXX-XXX-XXXX is PE series 1” EXP Diaphragm Pumps with
electronic interface
PE15X-XXX-XXX-XXXX is PE series 1- 1/2” EXP Diaphragm Pumps
with electronic interface
PE20X-XXX-XXX-XXXX is PE series 2” EXP Diaphragm Pumps with
electronic interface
PE30X-XXX-XXX-XXXX is PE series 3” EXP Diaphragm Pumps with
electronic interface
GENERAL DESCRIPTION
This manual is supplemental information for the electronic
interface options on the PE series of pumps. For complete
pump installation, disassembly and reassembly, safety infor-
mation, and other general pump information, please refer to
the PD pump manual that was also included with the pump.
This electronic interface includes options for solenoid control,
end of stroke feedback, leak detection (diaphragm failure),
cycle counting on the major valve, and a ported motor with
no major valve for user-supplied control directly to the two
diaphragm air chambers.
Solenoid control allows the cycle rate of the pump to be con-
trolled electronically.
With Solenoid control, when the solenoid is energized, the
pump strokes and dispenses the fluid in one chamber. When
the solenoid is de-energized, the pump strokes in the oppo-
site direction, dispensing the fluid in the other chamber.
By providing continuous ON - OFF signals to the solenoid, the
fluid transfer rate may be increased or decreased remotely.
End of stroke feedback can be used in conjunction with the
solenoid valve to cycle the pump based upon completion of
each stroke.
The leak detection option incorporates an optical fluid sensor
in each air chamber to provide a signal when a diaphragm
has failed and fluid is leaking through the pump.
The cycle counter option provides a closed contact output
each time the pump completes a cycle. This option is not
available combined with solenoid control.
The ported motor with no major valve is provided as an op-
tion for users who want to supply compressed air directly to
each diaphragm and control the operation of the pump with
their own external air controls.
MODEL DESCRIPTION CHART
PEXX X -XXX-XXX -X X X X
Pump Size
10 - 1” EXP Diaphragm Pumps
15 - 1- 1/2” EXP Diaphragm Pumps
20 - 2” EXP Diaphragm Pumps
30 - 3” EXP Diaphragm Pumps
Center Section
A - Aluminium
R - Polypropylene
S - Stainless Steel
Revision Level
Specialty Code 1 (Blank if no Speciality Code)
B - Solenoid 12VDC
D - Solenoid 24VDC
A - Solenoid 120VAC
C - Solenoid 240VAC
G - Solenoid 12VDC ATEX
H - Solenoid 24VDC ATEX
K - Solenoid 220VAC ATEX
N - Solenoid with no coil
P - Ported Motor (no major valve provided)
S - Cycle Sensing on Major Valve
0 - Standard Valve Block ( No Solenoid)
Specialty Code 2 (Blank if no Speciality Code)
F - End of stroke feedback
E - End of stroke feedback + Leak Detection
L - Leak Detection
Special Testing
Testing for special testing options, please contact your
nearest
ARO
Customer Service Representative or Distributor.
0 - No Option
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PEXXP-XXX-XXX-XXXX (en) Page 6 of 16 SOLENOID GENERAL DESCRIPTION Without end of stroke feedback, solenoid control can only be used to cycle the pump based on timing. The following curves represent the flow rates of a pump based on timed operation of the solenoid at a common operating point of 70 ps...
Page 7 of 16 PEXXP-XXX-XXX-XXXX (en) 140 141 200 233 105 107 107 236 135 � 139 138 � 137 � 136 111 419 � 421 420 134 133 429 417 403 415 418 416 407 428 414 413 figure 4 LUBRICATION / SEALANTS Apply Lubriplate fML-2 grease (94276) to all “O” rings, “U” cups and mating parts. SOLENOID PART LIST...
PEXXP-XXX-XXX-XXXX (en) Page 8 of 16 END Of STROKE GENERAL DESCRIPTION With end of stroke feedback from a pressure switch, the solenoid can be used to cycle the pump based on known feed- back that the pump has fully completed each stroke. PRESSURE SWITCH OPERATION A calibration procedure is necessar...
