Ingersoll Rand PD15P-X - Manual
Ingersoll Rand PD15P-X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPERATING AND SAFETY PRECAUTIONS
- Page 3 – Verify correct model / configuration prior to installation.
- Page 4 – SEAT OPTIONS; Service Kit; COMMON PARTS
- Page 5 – FOR THE; VIEW OF TWO PIECE PTFE DIAPHRAGM; TORQUE REQUIREMENTS; ALL FASTENERS ARE METRIC.; Torque Sequence
- Page 6 – AIR MOTOR PARTS; AIR MOTOR SECTION SERVICE; Air Motor Section Service is continued from Fluid Section repair.; PILOT VALVE DISASSEMBLY; LIPS MUST
- Page 7 – LUBRICATION / SEALANTS; PILOT VALVE; Figure 3
- Page 8 – TROUBLE SHOOTING; Product discharged from exhaust outlet.; DIMENSIONAL DATA; Figure 4; DIMENSIONS
E
2010
CCN 15197205
(800) 276-4658
D
FAX (800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
1-1/2” DIAPHRAGM PUMP
OPERATOR’S MANUAL
PD15P-X
RELEASED:
9-5-03
REVISED:
5-12-10
(REV. 12)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
PE15P-X
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637391-XX for fluid section repair (see page 4). NOTE: This kit also con-
tains several air motor seals which will need to be replaced.
637390-X major air valve assembly (see page 7).
PUMP DATA
Models
see Model Description Chart for “-XXX”.
. . . . . . . . . .
Pump Type
Non-Metallic Air Operated Double Diaphragm
. . . . . . .
Material
see Model Description Chart.
. . . . . . . . . .
Weight
PX15P-FKS-XXX
63.94 lbs (29.00 kgs)
. . .
. . . . . . .
PX15P-FPS-XXX
42.60 lbs (19.32 kgs)
. . . . . . .
PX15P-YKS-XXX
55.94 lbs (25.37 kgs)
. . . . . . .
PX15P-YPS-XXX
42.30 lbs (19.19 kgs)
. . . . . . .
Maximum Air Inlet Pressure
120 p.s.i.g. (8.3 bar)
. . . . . . . . .
Maximum Material Inlet Pressure
10 p.s.i.g. (0.69 bar)
. . . . .
Maximum Outlet Pressure
120 p.s.i.g. (8.3 bar)
. . . . . . . . . .
Maximum Flow Rate
(
flooded inlet
)
123.1 g.p.m. (465.9 l.p.m.)
. . . .
Displacement / Cycle @ 100 p.s.i.g.
0.617 gal. (2.34 lit.)
. . .
Maximum Particle Size
1/4” dia. (6.4 mm)
. . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM
-60
_
to 280
_
F (-51
_
to 138
_
C)
. . . . . . . . . . .
Hytrel
R
-20
_
to 150
_
F (-29
_
to 66
_
C)
. . . . . . . . . . . . . . . .
Nitrile
10
_
to 180
_
F (-12
_
to 82
_
C)
. . . . . . . . . . . . . . . . .
Polypropylene
35
_
to 175
_
F (2
_
to 79
_
C)
. . . . . . . . . . .
PVDF (Kynar
R
)
10
_
to 200
_
F (-12
_
to 93
_
C)
. . . . . . . . . .
Santoprene
R
-40
_
to 225
_
F (-40
_
to 107
_
C)
. . . . . . . . . . .
PTFE
40
_
to 225
_
F (4
_
to 107
_
C)
. . . . . . . . . . . . . . . . .
Viton
R
-40
_
to 350
_
F (-40
_
to 177
_
C)
. . . . . . . . . . . . . . . .
Dimensional Data
see page 8
. . . . . . . . . . . . . . . .
Mounting Dimension
8.687” x 14.937” (220.7 mm x 379.4 mm)
. . .
Noise Level
@ 70 p.s.i., 60 c.p.m.
81.0 db(A)
{
. . . . .
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability
.
PX15P-FXS-XXX
PX15P-YXS-XXX
MODEL DESCRIPTION CHART
P X 15 P - X X S - X X X
PX15P - XXS - X X X
637391 - X X
Diaphragm
Ball
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: Model # PD15P-FPS-PAA
Fluid Section Service Kit # 637391-AA
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene
M - Medical Grade Santoprene
C - Hytrel
T - PTFE / Santoprene
G - Nitrile
V - Viton
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Fluid Connection / Location
F - 1-1/2” A.N.S.I. / Din Flange / End
Y - 1-1/2” A.N.S.I. / Din Flange / Center
Center Section Material
P - Polypropylene
Ball Material
A - Santoprene
S - 316 Stainless Steel
C - Hytrel
T - PTFE
G - Nitrile
V - Viton
Electronic Interface
D - None
E - Available
www.ingersollrandproducts.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PD15P-X Page 2 of 8 OPERATING AND SAFETY PRECAUTIONS READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE. EXCESSIVE AIR PRESSURESTATIC SPARK HAZARDOUS MATERIALSHAZARDOUS PRESSURE WARNING EXCESSIVE AIR PRESSURE. Can cause person- al injury, pump damage or property damage...
Page 3 of 8 PD15P-X GENERAL DESCRIPTION The ARO diaphragm pump offers high volume delivery even at low airpressure and a broad range of material compatibility options available.Refer to the model and option chart. ARO pumps feature stall resistantdesign, modular air motor / fluid sections.Air operat...
MATERIAL CODE [B] = Nitrile [C] = Carbon Steel [E] = E.P.R. [H] = Hytrel [K] = P.V.D.F. (Kynar) [MSP]= Medical Grade Santoprene[P] = Polypropylene [SH] = Hard Stainless Steel[SP] = Santoprene[SS] = Stainless Steel[T] = PTFE [V] = Viton PD15P-X Page 4 of 8 PARTS LIST / PX15P-X FLUID SECTION FLUID SEC...
