Ingersoll Rand PD10P-X - Manual
Ingersoll Rand PD10P-X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPERATING AND SAFETY PRECAUTIONS
- Page 3 – WARNING; EXCESSIVE AIR PRESSURE. Can cause
- Page 4 – SERVICE KIT; COMMON PARTS; Polypropylene
- Page 5 – Torque Sequence; TORQUE REQUIREMENTS; ALL FASTENERS ARE METRIC.
- Page 6 – LIPS MUST FACE EACH OTHER.; AIR MOTOR PARTS; Qty
- Page 7 – Figure 3; TROUBLE SHOOTING; Product discharged from exhaust outlet.
- Page 8 – DIMENSIONAL DATA; DIMENSIONS; Figure 4
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 276-4658
y
FAX (800) 266-7016
© 2010
CCN 15206378
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED:
11
-1
0
-0
3
REVISED:
8-13-10
(REV. 12)
1” DIAPHRAGM PUMP
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
PD10P-X
PE10P-X
SERVICE KITS
Refer to Model Description Chart to match the pump material
options.
637397 for air section repair (see page 6).
637396-XX for fluid section repair (see page 4). NOTE: This
kit also contains several air motor seals which will need to be
replaced.
637395-7 major air valve assembly (see page 7).
PUMP DATA
Models . . . . . .
see Model Description Chart for “-XXX”.
Pump Type . . .
Non-Metallic Air Operated Double Diaphragm
Material . . . . .
see Model Description Chart.
Weight
. . . . . . .
PX10P-FKS-XXX . . . . . . . 27.15 lbs (12.32 kgs)
PX10P-FPS-XXX . . . . . . . 19.87 lbs (9.01 kgs)
PX10P-YKS-XXX . . . . . . . 26.72 lbs (12.12 kgs)
PX10P-YPS-XXX . . . . . . . 19.59 lbs (8.89 kgs)
PX10P-AKS-XXX, -BKS . . 25.83 lbs (11.72 kgs)
PX10P-APS-XXX, -BPS . . 19.35 lbs (8.78 kgs)
Maximum Air Inlet Pressure . . . . . . . .
120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . .
10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . .
120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (fl ooded inlet) . . .
53.0 g.p.m. (200.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . .
0.226 gal. (0.86 lit.)
Maximum Particle Size . . . . . . . . . . . .
1/8” dia. (3.2 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . . . . . . -60
0
to 280
0
F (-51
0
to 138
0
C)
Hytrel . . . . . . . . . . . . . . . . . . . . . -20
0
to 150
0
F (-29
º
to 66
0
C)
Nitrile . . . . . . . . . . . . . . . . . . . . . . 10
0
to 180
0
F (-12
º
to 82
0
C)
Polypropylene . . . . . . . . . . . . . . 35
0
to 175
0
F (2
0
to 79
0
C)
PVDF
(Kynar ) . . . . . . . . . . . . . 10
0
to 200
0
F (-12
0
to 93
0
C)
Santoprene . . . . . . . . . . . . . . . -40
0
to 225
0
F (-40
0
to 107
0
C)
PTFE
. . . . . . . . . . . . . . . . . . . . . . . . . 40
0
to 225
0
F (4
0
to 107
0
C)
Viton . . . . . . . . . . . . . . . . . . . . . -40
0
to 350
0
F (-40
0
to 170
0
C)
Dimensional Data . . . . . . . . . . . . . . . .
see page 8
Mounting Dimension . . . . .
5.032” x 10.050” (127.8 mm x 255.3 mm)
Noise Level
@ 70 p.s.i., 60 c.p.m. . . . . . 79.7 db(A)
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP
S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however,
certain combinations may not be recommended, consult a
representative or the factory if you have questions concerning
availability.
MODEL DESCRIPTION CHART
P X 10 P - X X S - X X X
PX10P - XXS - X X X
637396 - X X
Diaphragm
Ball
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # PD10P-FPS-PAA
FLUID SECTION SERVICE KIT # 637396-AA
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
A - Santoprene
M - Medical Grade Santoprene
G - Nitrile
V - Viton
Diaphragm Material
A - Santoprene
C - Hytrel
T - PTFE / Santoprene
G - Nitrile
V - Viton
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Fluid Connection / Location
A - 1" N.P.T.F. - 1
B - Rp 1 - 11 BS
F - 1" A.N.S.I. / DIN Flange / End
Y - 1" A.N.S.I. / DIN Flange / Center
Center Section Material
P - Polypropylene
Ball Material
C - Hytrel
T - PTFE
Electronic Interface
D - None
E - Available
PX10P-AXS-XXX
PX10P-BXS-XXX
PX10P-YXS-XXX
PX10P-FXS-XXX
Figure 1
www.ingersollrandproducts.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 8 PD10P-X EXCESSIVE AIR PRESSURESTATIC SPARK HAZARDOUS MATERIALSHAZARDOUS PRESSURE WARNING EXCESSIVE AIR PRESSURE. Can cause per- sonal injury, pump damage or property damage.Do not exceed the maximum inlet air pressure as stated on the pump model plate.Be sure material hoses and other com...
PD10P-X Page 3 of 8 GENERAL DESCRIPTION The ARO diaphragm pump off ers high volume delivery even at low air pressure and a broad range of material compatibility options available. Refer to the model and option chart. ARO pumps feature stall resistant design, modular air motor / fl uid sections. Air ...
Page 4 of 8 PD10P-X FLUID SECTION SERVICE KITS (637396-XX) KITS INCLUDE: BALLS (see Ball Option, refer to -XX in Service Kit chart below), DIAPHRAGMS (see Diaphragm Option, refer to -XX in Service Kit chart below), and items 19, 33, 70, 144, 175 and 180 (listed below) plus 174 and 94276 Lubriplate...
