Ingersoll Rand GRG15M06G9 - Manual
Ingersoll Rand GRG15M06G9 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Always match collet size with accessory shank size.
- Page 3 – LUBRICATION
- Page 5 – MANUEL DE L’OPERATEUR; ARO Tool Products; MEULEUSES, PONCEUSES ET POLISSEUSES D’ANGLE; ATTENTION; Utiliser les accessoires recommandés par ARO.; NOTE
- Page 6 – SIGNIFICATION DES ÉTIQUETTES D’AVERTISSEMENT; AVERTISSEMENTS SPÉCIFIQUES AUX MEULEUSES
- Page 7 – AVERTISSEMENTS PARTICULIERS AUX PONCEUSES/POLISSEUSES; MISE EN SERVICE DE L’OUTIL; LUBRIFICATION
- Page 8 – SPÉCIFICATIONS
- Page 9 – GUÍA DEL OPERARIO; MANEJO, INSTALACIÓN Y MANTENIMIENTO; LIJADORAS Y PULIDORAS, AMOLADORAS; SE ADJUNTA INFORMACIÓN IMPORTANTE DE SEGURIDAD.; NOTA
- Page 10 – ETIQUETAS DE AVISO; AVISOS ESPECÍFICOS SOBRE LAS AMOLADORAS; AVISO
- Page 11 – LUBRICACIÓN
- Page 12 – PARA PONER LA HERRAMIENTA EN SERVICIO; ESPECIFICACIONES
- Page 13 – MANUAL DO OPERADOR; ESMERILADORAS, LIXADORAS E POLIDORAS; arranjo típico de tubagem.; USANDO A FERRAMENTA; Use acessórios recomendados pela ARO.
- Page 14 – IDENTIFICAÇÃO DO RÓTULO DE ADVERTÊNCIA; ADVERTÊNCIAS ESPECÍFICAS SOBRE A ESMERILADORA; ADVERTÊNCIA
- Page 15 – LUBRIFICAÇÃO
- Page 16 – COLOCANDO A FERRAMENTA EM FUNCIONAMENTO; ESPECIFICAÇÕES
- Page 17 – MAINTENANCE SECTION
- Page 18 – PART NUMBER FOR ORDERING
- Page 21 – General Instructions; For GRG15A or GRG15M Models:
- Page 22 – For GRP15A or GRS15A Models:; Disassembly of the Throttle Lever and Inlet
- Page 23 – Disassembly of the Bevel Pinion Driver; ASSEMBLY
- Page 24 – Assembly of the Motor and Throttle
- Page 25 – Assembly of the Throttle Lever and Inlet
- Page 26 – Assembly of the Angle Head
- Page 27 – TROUBLESHOOTING GUIDE; Trouble
- Page 28 – SAVE THESE INSTRUCTIONS. DO NOT DESTROY.
M10
180
4–30–94
11–4–99
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
SECTION
MANUAL
Released:
Revised:
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll–Rand Distribution Center,
White House, TN at PH: (615) 672–0321, FAX: (615) 672–0801
ARO Tool Products
Ingersoll–Rand Company
1725 U.S. No. 1 North, PO Box 8000, Southern Pines, NC 28388–8000
1999 INGERSOLL–RAND COMPANY PRINTED IN U.S.A
MODELS GRG15A–06G–7, GRG15A–06G–9, GRG15A–08G–7,
GRG15M–06G–7, GRG15M–06G–9, GRG15M–08G–7,
GRP15A–02P–7, GRS15A–04S–9, AND GRS15A–06S–7
1.5 H.P. ANGLE GRINDERS, POLISHERS, AND SANDERS
GRG Air Angle Grinders, GRS Air Angle Sanders and GRP Air Angle polishers are designed for smooth-
ing, trimming or removing metal in close–quarter areas in foundries, shipyards, steel mills and in
construction applications.
ARO is not responsible for customer modification of tools for applications on which ARO was not
consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
•
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/10” (10 mm) inside diameter air supply
hose.
•
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air at 90 psig (6.2 bar/
620 kPa) maximum air pressure. Dust, corrosive
fumes and/or excessive moisture can ruin the
motor of an air tool.
•
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
•
Always wear hearing protection when operating
this tool.
•
Keep hands, loose clothing and long hair away
from rotating end of tool.
•
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
•
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
•
Tool accessories may continue to rotate briefly
after throttle is released.
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain oc-
curs. Seek medical advice before resuming use.
•
Use accessories recommended by ARO.
•
Whenever the Angle Head is installed or reposi-
tioned, the Throttle Lever must be positioned so
that reaction torque will not tend to retain the
throttle in the “ON” position.
•
This tool is not designed for working in explosive
atmospheres.
•
This tool is not insulated against electric shock.
The use of other than genuine ARO replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest ARO Tool Products Authorized
Servicenter.
F
E
P
F
E
P
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M10180 2 WARNING LABEL IDENTIFICATION FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Always wear eye protectionwhen operating or perform-ing maintenance on thistool. WARNING WARNING Always wear hearing protection when operatingthis tool. Always turn off the air sup-ply and disconn...
M10180 3 SANDER/POLISHER SPECIFIC WARNINGS • These Sanders and Polishers will operate at the free speed specified on the nameplate if the air supply line furnishes 90 psig (6.2 bar/620 kPa) air pressure at the tool. Operation at higher air pressure will result in excessive speed. • Use only a sandin...
MANUEL DE L’OPERATEUR COMPRENANT : EXPLOITATION, INSTALLATION & ENTRETIEN ARO Tool Products Ingersoll–Rand Company 1725 U.S. No. 1 North, PO Box 8000, Southern Pines, NC 28388–8000 1999 INGERSOLL–RAND COMPANY Imprimé aux E.U. Pour les informations relatives aux pièces et au service, contactez ...
