Ingersoll Rand 67165-X - Manual
Ingersoll Rand 67165-X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
E
2006
CCN 99711780
&
(800) 276-4658
D
FAX (800) 266-7016
INGERSOLL RAND COMPANY
LTD
P.O. BOX 151
D
ONE ARO CENTER
D
BRYAN, OHIO 43506-0151
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
SOLENOID ACTUATED PUMP KITS
FOR DIAPHRAGM PUMPS
67165-X
67166-X
67277-X
RELEASED:
3-6-98
REVISED:
3-7-06
(REV. G)
SOLENOID ACTUATED PUMP KITS
67165-( ) for 3/8" and 1/2" diaphragm pumps, as follows:
66605X-X, PD03P-X-X, PD05P-X-X, PD05P-X-X-B, PD05R-X-X-B
and PM05P-X-X-A02.
67166-( ) for 1", 1-1/2" and 2" non-metallic diaphragm pumps as follows:
6661AX-X-C, 6661BX-X-C, 6661TX-X-C, 6661UX-X-C, 6662AX-X-C
and 6662BX-X-C.
67166-( ) for 1" and 1-1/2" metallic diaphragm pumps as follows:
66610X-X-C, 66611X-X-C, 66612X-X-C, 66613X-X-C, 66615X-X-C,
66616X-X-C, 66617X-X-C and 66618X-X-C.
67277-( ) for 2" and 3" metallic diaphragm pumps as follows:
PD20A-X-X, PF20A-X-X, PM20A-X-X-A02, PD30A-X-X-B and
PM30A-X-X-B02.
GENERAL DESCRIPTION
ARO solenoid actuated diaphragm pump kits allow the cycle rate of the
pump to be controlled electronically. When the solenoid is energized, the
pump strokes and dispenses the fluid in one chamber. When the sole-
noid is de-energized, the pump strokes in the opposite direction, dis-
pensing the fluid in the other chamber.
By providing continuous ON - OFF signals to the solenoid, the fluid
transfer rate may be increased or decreased remotely.
Some parts of the pump must be replaced with those included in these
kits to enable solenoid actuation.
67165-( ) SOLENOID KIT INSTALLATION
3/8” AND 1/2” DIAPHRAGM PUMPS
Refer to figure 1.
1. Remove (134) bolts from the major valve and remove (135) valve
block.
2. Remove (136) plug and replace with 93909 or 96462 plug.
3. Place 94640 plug in pilot hole.
4. Attach (135) valve block to (101) motor body, using (133) washers
and (134) bolts. NOTE: Torque to 15 - 20 in. lbs (1.7 - 2.3 Nm).
5. Thread CAT33P-( )-( ) valve assembly into air supply port.
6. Connect CAT33P-( )-( ) valve with 93909 plug, using 94981-XXX-X
tube.
132
135
133
.
134
Identification dot this side.
k
Assemble with 2 identification dots toward (132) gasket.
.
Torque to 15 - 20 in. lbs (1.7 - 2.3 Nm).
~
Supplied with 67165-( ) Kit.
Z
See page 4 for coil options.
g
94981-XXX-X Bulk Tubing (100’ long).
~
Valve
(see table)
93909
~
Figure 1
136
141
k
140
94640
~
~
94981-XXX-X
(5" long)
g
MODEL
VALVE
VOLTAGE
67165-1
CAT33P-024-D
24 VDC
67165-2
CAT33P-120-A
120 VAC
67165-3
CAT33P-000-N
No Coil
Z
~
59756-4
~
676
~
90351
59756-4
~
Y325-125
~
NOT SHOWN
CHW Connector
~
Y325-29
~
96462
~
59756-4
96214-2
~
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
