Ingersoll Rand 66610X-x-c - Manual
Ingersoll Rand 66610X-x-c – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – = Hazards or unsafe practices which; OPERATING AND SAFETY PRECAUTIONS
- Page 3 – WARNING; EXCESSIVE AIR PRESSURE. Can cause
- Page 4 – SEAT OPTIONS; SERVICE KIT; Item; COMMON PARTS; Rod; Item Description
- Page 5 – NOTE: DO NOT OVERTIGHTEN FASTENERS
- Page 6 – 04 Retaining Ring, TruArc; AIR MOTOR SECTION SERVICE; Service is divided into two parts − 1. Pilot Valve, 2. Major; PILOT VALVE DISASSEMBLY; MAJOR VALVE DISASSEMBLY; NOTE: Be careful to orient spacer legs away from
- Page 7 – Figure 3
- Page 8 – TROUBLE SHOOTING; Product discharged from exhaust outlet.; DIMENSIONAL DATA
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET - BRYAN, OHIO 43506
(800) 495-0276
FAX (800) 892-6276
© 2013
CCN 81376642
www.ingersollrandproducts.com
OPERATOR’S MANUAL
66610X-X-C
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED:
8-24-89
REVISED:
12-03-13
(REV. AD)
1” DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to the Model Description Chart to match the pump material op-
tions.
637118 - C for air section repair (see page 6).
637119 - XX -C for fluid section repair (see page 4).
637167 Abrasion Resistant Conversion Kit is available for use in heavy
and abrasive material applications (see page 4).
PUMP DATA
Models . . . . . . . . . . . . see “Model Description Chart” for “-XXX”
Pump Type . . . . . . . . . Metallic Air Operated Double Diaphragm
Material . . . . . . . . . . . . see “Model Description Chart”
Weight . . . . Aluminum . . . . . . . . . . . 19 lbs (8.62 kgs)
Cast Iron . . . . . . . . . . . . 31 lbs (14.06 kgs)
Stainless Steel . . . . . . . . 36 lbs (16.33 kgs)
[add 8 lbs (3.63 kgs) for cast iron air motor section]
Maximum Air Inlet Pressure . . . . . . . . 120 p.s.i. (8.3 bar)
Maximum Material Inlet Pressure . . . . 10 p.s.i. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . 120 p.s.i. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . . 35 g.p.m. (133 l.p.m.)
Displacement / Cycle @ 100 p.s.i.
Standard Diaphragm..................0.16 gal. (0.60 lit.)
Composite PTFE Diaphgram......0.14 gal. (0.525 lit.
)
Maximum Particle Size . . . . . . . . . . . 1/8” dia. (3.2 mm)
Maximum Temperature Limits (diaphragm / ball / seat mate-
rial)
Acetal . . . . . . . . . . . . . . . . . 10⁰ to 180⁰ F (-12⁰ to 82⁰ C)
E.P.R. / EPDM . . . . . . . . . . . -60⁰ to 280⁰ F (-51⁰ to 138⁰ C)
Hytrel® . . . . . . . . . . . . . . . . -20⁰ to 150⁰ F (-29⁰ to 66⁰ C)
Neoprene . . . . . . . . . . . . . . 0⁰ to 200⁰ F (-18⁰ to 93⁰ C)
Nitrile . . . . . . . . . . . . . . . . . 10⁰ to 180⁰ F (-12⁰ to 82⁰ C)
Polypropylene . . . . . . . . . . . 35⁰ to 175⁰ F (2⁰ to 79⁰ C)
Polyurethane . . . . . . . . . . . . 10⁰ to 150⁰ F (-12⁰ to 66⁰ C)
Kynar® PVDF . . . . . . . . . . . 10⁰ to 200⁰ F (-12⁰ to 93⁰ C)
MODEL DESCRIPTION CHART
Santoprene®. . . . . . . . . . . -40 to 225 F (-40 to 107⁰ C)
PTFE . . . . . . . . . . . . . . . . . 40⁰ to 225⁰ F (4⁰ to 107⁰ C)
Viton® . . . . . . . . . . . . . . . . -40⁰ to 350⁰ F (-40⁰ to 177⁰ C)
Dimensional Data . . . . . . . . . . . . . . . see page 8
Noise Level @ 70 p.s.i., 60 c.p.m . . 64.5dba(A)*
* The pump sound pressure levels published here have been updated to an Equivalent Continu-
ous Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four
microphone locations.
NOTICE: All possible options are shown in the chart. However, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
6661 X X X X X C
6661XX X X X C
C
637119 X X
DIAPHRAGM
BALL
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # 666100-361-C
Fluid Section Service Kit # 637119-61-C
CENTER BODY MATERIAL
FLUID CAP / MANIFOLD MATERIAL
0
- Aluminum, N.P.T.F
2
- Aluminum, BSP
1
- Cast Iron, N.P.T.F
3
- Cast Iron, BSP
Seat Material
1
- Aluminum
4
- Kynar PVDF
2
- 316 Stainless Steel
5
- Carbon Steel
3
- Polypropylene
Ball Material
8
- Hard 440 Stainless Steel
0
- Aluminum, Single
A
- Aluminum, BSP
(Steel Hardware)
(Stainless Steel Hardware)
1
- Stainless Steel, Single
B
- Stainless Steel, Single
2
- CastIron, Single
C
- Cast Iron, Single
9
- StainlessSteel, Dual
D
- Stainless Steel, Dual
1
- Neoprene
6
- Acetal
2
- Nitrile
8
- Polyurethane
3
- Viton
A
- Stainless Steel
4
- PTFE
C
- Hytrel
5
- E.P.R.
E
- Santoprene
DiaphragmMaterial
1
- Neoprene
2
- Nitrile
4
- PTFE / Santoprene
3
- Viton
5
- E.P.R.
6
- Composite PTFE
9
- Hytrel
B
- Santoprene
6661XX-XXX-C
1’’ DIAPHRAGM PUMP
DUAL MANIFOLD
SINGLE MANIFOLD
Figure 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 8 66610X-X-C (en) 66610X-X-C (en) EXCESSIVE AIR PRESSURE STATIC SPARK HAZARDOUS MATERIALS HAZARDOUS PRESSURE WARNING EXCESSIVE AIR PRESSURE. Can cause personal injury, pump damage or property damage. Do not exceed the maximum inlet air pressure as stated on the pump model plate. Be sure ma...
66610X-X-C (en) Page 3 of 8 Page 3 of 8 GENERAL DESCRIPTION The ARO diaphragm pump offers high volume delivery even at low air pressure and a broad range of material compatibility op- tions available. Refer to the model and option chart. ARO pumps feature stall resistant design, modular air motor / ...
Page 4 of 8 66610X-X-C (en) 66610X-X-C (en) PARTS LIST / 66610X-X-C FLUID SECTION 637119 - XX - C Fluid Section Service Kits include: BALLS (see Ball Option, refer to -XX in chart below), DIAPHRAGMS (see Diaphragm Option, refer to -XX in chart below), packet, plus items: 2, 3, 9 and 19 and 93706-1...
