Ingersoll Rand 1875CXXXXXX - Manual
Ingersoll Rand 1875CXXXXXX – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MODEL DESCRIPTION CHART
- Page 3 – LOWER PUMP DISASSEMBLY; Thoroughly clean and lubricate all seals. Replace all soft; TROUBLE SHOOTING; Material leakage out of solvent cup.; PARTS LIST
- Page 4 – ASSEMBLY TORQUE REQUIREMENTS; Apply Loctite nickel anti-seize to threads.; Figure 2
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX (800) 892-6276
© 2010
CCN 46730388
www.ingersollrandproducts.com
OPERATOR’S MANUAL
1875CXXXXXX
INCLUDING: SERVICE KITS, TROUBLESHOOTING, PARTS LIST,
DISASSEMBLY & REASSEMBLY.
RELEASED:
9-15-10
(REV. 01)
1875CXXXXXX
LOWER PUMP END
Also covers K1875CXXXXXX service kits
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
The original language of this manual is English.
GENERAL DESCRIPTION
WARNING
DO NOT EXCEED MAXIMUM OPERATING PRES-
SURE AS INDICATED ON PUMP MODEL PLATE.
WARNING
REFER TO GENERAL INFORMATION SHEET FOR
ADDITIONAL SAFETY PRECAUTIONS AND IMPORTANT IN-
FORMATION.
This manual covers the lower pump section. It is one of four
documents which support an ARO pump. Replacement copies
of these forms are available upon request.
Pump Model Operator’s Manual.
General Information for Air / Hydraulically Operated Piston
Pumps.
Lower Pump End Operator’s Manual.
Air / Hydraulic Motor Operator’s Manual.
MAINTENANCE
The air / hydraulic motor is completely separate from the lower
pump end. This helps to keep the motor from being contaminated
by the material being pumped. Periodically, flush entire pump
system with a solvent that is compatible with the material being
pumped.
Keep solvent cup filled with this compatible solvent. This will
keep the material from drying on the plunger, which would drag
through the packings, ruin them and eventually scour the plunger.
Provide a clean work surface to protect sensitive internal moving
parts from contamination from dirt and foreign matter during dis-
assembly and reassembly.
Before reassembling, lubricate parts as required. When assembling
“O” rings, or parts adjacent to “O” rings, exercise care to prevent
damage to “O” rings and “O” ring groove surface.
Figure
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
1875CXXXXXX (en) Page 2 of 4 1875 C X X X X X X Check Type / Wetted Material C - Two Ball, 300 Series / CF8M Stainless Steel Container Suitability 1 - Remote Mounting 5 - 55 gallon 8 - Remote Mounting with Optional Inlet9 - 5 gallon with Optional Piston MODEL DESCRIPTION CHART Inlet / Outlet Tread T...
Page 3 of 4 1875CXXXXXX (en) MATERIAL CODE [B] = Nitrile [SS] = Stainless Steel [CSS] = Ceramic coated Stainless Steel [T ] = PTFE [D] = Acetal [Ny] = Nylon [UH] = UHMW-PE [V ] = Viton LOWER PUMP DISASSEMBLY NOTE: All threads are right hand. Secure the lower pump assembly in a vise, clamping on fl a...
Page 4 of 4 1875CXXXXXX (en) PN 97999-1583 PARTS LIST ASSEMBLY TORQUE REQUIREMENTS NOTE: DO NOT OVERTIGHTEN FASTENERS. (3) spacer tube, (21) suction tube and (26) foot valve body 125 - 150 ft lbs (165.5 - 203.4 Nm).(13) connector rod and (14) cup follower 50 ft lbs (67.8 Nm). (18) inner check seat 6...
