Page 3 - FCC Warning; Canada
1 Declaration of Conformity Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USAWe declare under our sole responsibility that this projector conforms to the following directives and norms: ErP Directive 2009/125/ECEMC Directive 2004/108/ECEMC: EN 55022...
Page 4 - Troubleshooting your setup
2 Table of ContentsIntroduction 4Positioning the projector 6 Connecting a computer source 8 VGA connection 8 Connecting power 8 Optional computer connections 8 Displaying an image 9 Adjusting the image 10 Connecting a video device 11 Video device connections 11 HDMI connection 11 Composite video con...
Page 5 - Important Operating Considerations for Safety
3 Important Operating Considerations for Safety • Refer to this guide for proper startup and shutdown procedures. • Follow all warnings and cautions in this manual and on the projector. • Place the projector in a horizontal position no greater than 15 degrees off axis. • Locate the projector at leas...
Page 6 - Introduction; with a wide variety of computers and video devices.; Product specifications
4 Introduction Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. IN112a/IN112aT has native SVGA 800 x 600 resolution, IN114a/IN114aT/IN114STa has na...
Page 7 - Connector panel; Monitor out, for VGA pass through to an external monitor.
5 Connector panel The projector provides both computer and video connection options, including:• VGA computer (2) • Composite video (model dependent) • HDMI (model dependent) • S-video (model dependent) • USB connector for firmware upgrades, mouse control and Screen Save mode. • Monitor out, for VGA...
Page 8 - Positioning the projector
6 Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines: • Position the projector on a flat surfac...
Page 9 - Connecting a computer source; VGA connection; monitor cable from the computer’s video port first.; HDMI connection; shipped with the projector.; Optional computer connections; included) to your computer and to th Audio 1/Audio 2 connector on the
7 Connecting a computer source VGA connection Connect one end of the provided computer cable to th Computer 1/Computer 2 connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the compute...
Page 10 - Displaying an image; and the fans start to run. When the lamp comes on,
8 Displaying an image Press the Power button.The Power LED lights blue, and the fans start to run. When the lamp comes on, the start up screen displays. It can take up to a minute for the image to achieve full brightness. Note: When the feature, AC Power On, is enabled, the projector automatically t...
Page 11 - Adjusting the image; See page 6 for a table listing screen sizes and distances.
9 Adjusting the image If necessary, adjust the height of the projector by rotating the elevator foot to extend the foot. If necessary, rotate the leveling foot located at the rear of the projector. Avoid placing your hands near the hot exhaust vent at the front of the projector. Position the project...
Page 12 - Connecting a video device; InFocus or provide your own.
10 Connecting a video device You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the pr...
Page 13 - Shutting down the projector; Auto Off Time; stop. Unplug the power cable to completely power off the projector.; projector and can help you troubleshoot.; Table 4: Status Indicator Lights; Status Indicator Light
11 Shutting down the projector Auto Off Time The projector also has an Auto Off Time feature that automatically turns the projector off after no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can change the len...
Page 14 - Startup
Problem Solution Result No start up screen Plug power cord into the projectorpress the Power button Startup Screen Correct image A Startup Screen Only start up screen appears Restart laptop Press the SOURCE buttonactivate laptop’s external port A A Computer image projected 12
Page 15 - Computer image projected
13 Problem Solution Result No computer image, just the words “Signal out of range” A Signal out of the range Press the Auto Image button on remoteAdjust computer refresh rate (Windows 7: Control Panel > Display > Screen Resolution > Advanced Settings > Adapter tab). Varies per operating ...
Page 18 - COLOR
A 16 Image upside down Aspect Ratio Auto Image Brightness Contrast Auto Keystone Keystone Presets Sharpness Volume Ceiling Mount Advanced Menu Auto Execute 50 50 Off 0 Presentation 16 16 Off ( Basic Menu ) MDL: IN112a FW: 0.14 Turn off Ceiling Mount in Basic menu Correct image Image reversed left to...
Page 21 - Using the remote control; Troubleshooting the remote
19 Using the remote control The remote uses two (2) AAA batteries (not provided). They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.Caution: • When replacing the remote batteries, ...
Page 22 - Using the audio; Using the projector’s speakers; through the projector speakers.; Troubleshooting Audio; Make sure the correct source is active.
20 Using the audio Using the projector’s speakers Connect the audio source to the Audio 1/Audio 2 connectors to hear audio through the projector speakers. Amplified speakers may also be connected to the projector using the Audio Out connector. To adjust the volume, press the Volume buttons on the re...
Page 23 - Using the keypad buttons; Auto - Resynchronizes the projector to the source.
21 Using the keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions:Power–turns the projector on and off (page 8). Right arrow - When the menu is displayed, the right arrow button navigates through the menu. Up arrow/Keystone - When the menu...
Page 24 - and current source. See page 27 for details.
22 Optimizing computer images After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 24.• Select default image settings using a preset appropriate to your environment. • Adjust the Keyst...
Page 26 - Using the menus; Press the Menu button to exit the menu system.
24 Using the menus 1 To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to review the menu options. 2 To enter a submenu, highlight the desired submenu and press > ...
Page 28 - Phase: adjusts the horizontal phase of a computer source.
26 Advanced Menu Image: 3D Control: 3D: allows you to enjoy 3D (stereoscopic) content. Your projector supports Auto, Top-Bottom, Frame Sequential, Frame Packing, Side-by-Side for con-trolling LCD shutter glasses. In addition to the projector, you will need a pair of 3D shutter glasses, 3D content, a...
Page 32 - Maintenance; Cleaning the lens; Apply a non-abrasive camera lens cleaner to a soft, dry cloth.; Using the security lock
30 Maintenance Cleaning the lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Projector must be off and the lens must be at room temperature. • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other har...
Page 33 - Replacing the projection lamp; lamp has been in use.
31 Replacing the projection lamp The Lamp Hours timer in the Projector Info menu counts the number of hours the lamp has been in use. • NOTE: Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from www.infocus.com (in select areas), your retailer or your deal...
Page 35 - Numerics; Video device 11
33 Numerics 3D Sync Invert 26 A AC Power On 28Aspect Ratio 25Audio 1/Audio 2 8Auto Image 25Auto Off Time 29Auto Source 28AV Mute 27 B Blank Key 27Blank Screen 27Brightness 25 C Cable box 11Ceiling Mount 25, 27Closed Captions 27Color Space 26Computer 1 27Computer 1/Computer 2 8Computer 2 27Connecting...
