Ikelite Film Camera - Manual

IIKKEELLIITTEE SSIIN

NGGLLEE CCO

ORRD

D//

N

NIIKKO

ON

NO

OSS--SSTTYYLLEE #

#44110044..66

SSIIN

NGGLLEE SSYYN

NCC CCO

ORRD

D #

#44110044..66____________________________________

Connects a single (1) Ikelite Substrobe to a Nikonos IV, V, RS camera or

suitable FILM camera housing that utilizes the Nikonos-style flash socket

for external strobe connection. The strobes will fire in TTL automatic or

manual exposure modes using the Nikons V or RS. Strobes will only work

in the manual mode with the Nikonos IV or camera housings.

O

ON

NLLYY IIKKEELLIITTEE TTTTLL SSU

UBBSSTTRRO

OBBEESS CCAAN

N BBEE CCO

ON

NN

NEECCTTEEDD..

D

DO

O N

NO

OTT use the TTL cord on a non TTL strobe; you will damage

the camera.

D

DO

O N

NO

OTT remove the sync cord from the strobe or camera underwater

or when wet. Connections are NOT waterproof when

disconnected underwater.

D

DO

O N

NO

OTT leave the cord connected

for prolonged periods. Otherwise,

the cord may freeze to the strobe

or camera. After each dive,

disconnect the cord and lightly

lubricate the connector threads.

Never use spray lubricant.

Nikonos Style

Connector

CCO

ON

NN

NEECCTTIIN

NGG TTH

HEE SSTTRRO

OBBEE __________________________________________________________________________

1. Make sure all components are dry.
2. Clean and lightly lubricate the stem o-ring and the strobe

connector threads. Check the o-ring for nicks or cuts.

3. Note the positioning of the receptacles and pins.

Properly align the end of the sync cord and insert into

the strobe connector.

4. Hand-tighten the Retaining ring on the sync cord.
5. Push the connector body further into the strobe connector

and continue to tighten the Retaining ring.

CCO

ON

NN

NEECCTTIIN

NGG TTO

O TTH

HEE CCAAM

MEERRAA O

ORR H

HO

OU

USSIIN

NGG________________________________________

1. Make sure all components are dry. Clean and lightly

lubricate the stem shaft, o-ring and retaining ring threads.

Check the stem o-ring for nicks or cuts.

2. Align the index groove with the Indexing Pin of the flash

socket, and insert the stem into the flash socket.

3. Rotate the retaining ring counter clockwise until it

mates with the flash socket threads. Then carefully

rotate retaining ring clockwise and thread it into the

flash socket until snug.

LLIIM

MIITTEED

D W

WAARRRRAAN

NTTYY______________________________________________________________________________________

All Ikelite products are warranted against any manufacturing defects for

a period of one (1) year from the date of purchase. Defective products

should be returned prepaid to Ikelite. Ikelite will, at its discretion, repair or

replace such products, and will return to customer prepaid. All other claims,

of any nature, including but not limited to bulb failure are not covered. Except

as mentioned above, no other warranty expressed or implied, applies to this

Ikelite product.

IIKKEELLIITTEE U

UN

ND

DEERRW

WAATTEERR SSYYSSTTEEM

MSS

50 West 33rd Street, P.O. Box 88100,

Indianapolis, IN 46208 USA

(317) 923-4523

4104.6-01-0706

Retaining
Ring

Index Groove

Stem O'ring

Red Retainer
O'ring

Retaining
Ring

Index Groove

Stem O'ring

Red Retainer
O'ring

Blue
Band

Retaining
Ring

Stem O'ring

Retaining
Ring

Stem O'ring