Ice-O-Matic IOD200 - Manual

Page 2 - Page

Introduction IOD150,IOD200,IOD250 To the owner or user: This product manual is a source of information about the installation, start up, cleaning, maintenance and repair of the product. The IOD150, IOD200 and IOD250 are ice only counter top dispensers designed to use 22 inch wide and 30 inch wide re...

Page 3 - Specifications and Limitations; Dispenser Specifications

Specifications and Limitations IOD150, IOD200, IOD250 Limitations: Must meet the same limitations as the cuber installed on top of it: 50 ° F. air minimum 100 ° F. air maximum Must be installed indoors. Must allow at least 6-inch clearance at the rear and both sides when using an air-cooled ice mach...

Page 4 - For The Installer; Site Preparation

For The Installer IOD150, IOD200, IOD250 Equipment Description The IOD150, IOD200 and IOD250 are counter top mounted ice only dispensers. These units are designed to dispense cube ice only and have ice storage capacities of 150 lb.,220 lb. and 250 lb. respectively. Site Preparation The site chosen f...

Page 5 - Installation; the cover and for pouring ice into the hopper.; Note: Before installing legs the plastic plugs must be removed.

Installation IOD150, IOD200, IOD250 1. Locate the ice dispenser on the counter. Allow vertical clearance above the unit for the removal of the cover and for pouring ice into the hopper. 2. Plan the unit drain. A one-inch (1”) I.D. drain tube is required for draining. Routing is either through the ba...

Page 6 - Water Glass Filler Kit; Remove the lower front panel; Maximum water pressure is

Water Glass Filler Kit IOD150, IOD200, IOD250 Installation Instructions WARNING: Disconnect power to unit before proceeding with installation. 1. Prepare the unit as follows: · Remove the lower front panel · Locate faucet-mounting holes in the front panel. (Reference page 6 for hole locations) 2. In...

Page 8 - Initial Start Up; CAUTION; : Use caution to avoid spilling ice; Completion

Initial Start Up IOD150, IOD200, IOD250 1. Sanitize the ice storage system as instructed on Page 10. 2. Fill the hopper with sanitary ice. 3. Plug the unit’s power cord into an electrical outlet and the lighted sign should come on. 4. Dispense several containers of ice. Note: In normal operation, pu...

Page 9 - Gate Restrictor Plate

Gate Restrictor Plate IOD150, IOD200, IOD250 CAUTION: Disconnect power to dispenser and ice machine before installing, removing or adjusting restrictor. ADJUSTMENT This plate may be adjusted as shown to reduce or increase the dispensing rate of ice, especially desirable when using glasses or other c...

Page 10 - vending area. Check for proper water drainage from the vending; Monthly; Clean and sanitize the hopper interior.; WARNING

Cleaning and Sanitizing IOD150, IOD200, IOD250 The sink, grill and splash panel area should be cleaned daily. The following dispenser maintenance should be performed at the intervals indicated: Daily (Or As Required) Remove foreign material from vending area drip tray to prevent drain blockage. Week...

Page 11 - Cleaning and Sanitizing; Note: This should be done by qualified personnel.; solution and rinse thoroughly to remove all traces of detergent.

Cleaning and Sanitizing IOD150, IOD200, IOD250 MONTHLY AND INITIAL START UP: Sanitize the Ice Storage System. Note: This should be done by qualified personnel. CLEANING PRECAUTIONS WARNING : Disconnect Power Before Cleaning! Do not use metal scrapers, sharp objects or abrasives on the ice storage ho...

Page 12 - Troubleshooting

Troubleshooting IOD150, IOD200, IOD250 IMPORTANT: only qualified personnel should service internal components or electrical wiring. Should the dispenser fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check the followin...

Page 13 - Wiring Diagram