Ice-O-Matic ICEU060 - Manual

Page 3 - Specifications ICEU060; Operating Requirements; Air Temperature

Specifications ICEU060 Page 2 Specifications: 24 Hour Bin Storage Basic Maximum Ref Type. Model Number Capacity Capacity Electrical Fuse Size Ounces ICEU060 55 lbs. 28 lbs. 115/60/1 15 R134a, 9.5 oz Operating Requirements : Minimum Maximum Air Temperature 50 ° F 100 ° F Water Temperature 40 ° F 100 ...

Page 4 - Installation ICEU060; F and with a maximum; must; remain unobstructed. Do not block the front panel area with

Installation ICEU060 Page 3 Location: Prior consideration for the location of the ice machine shall include: Installation location to be indoors with a minimum room temperature of 50 ° F and with a maximum room temperature of 100 ° F. The incoming water temperature to the machine should be between 4...

Page 5 - pressure should be 20 psig.; Electrical; Under no circumstances must the ground post be altered or removed

Installation ICEU060 Page 4 Water Supply and Drain Connection: 1. The recommend water supply line is ¼ inch O.D. copper tubing. The minimum incoming water pressure should be 20 psig. 2. Connect the water supply tubing to the water inlet fitting (3/4 hose thread) at the rear of the icemaker. An optio...

Page 6 - circulation around the machine, and where it can be serviced?

Installation ICEU060 Page 5 Final Check: 1. Is the cabinet level?2. Have all the electrical and piping connection been made?3. Has the voltage been tested and checked against the nameplate rating?4. Is the unit plugged into a separate electrical circuit?5. Is the water supply line shut off valve ins...

Page 7 - Initial Start Up ICEU060; ON

Initial Start Up ICEU060 Page 6 1. Open the water supply valve.2. Move electrical breaker or switch to the ON position. 3. Remove the front panel.4. Check the cube size control shaft, it should be in a preset position. If not, rotate the control shaft clockwise until the unit comes on. Note: Cube si...

Page 8 - makes a circuit to the compressor. When moved to the; OFF; position, the other components will still

How It Works ICEU060 Page 7 Component Description Cube Size Control The Cube size control is located in the front of the control box, behind the front panel. The sensing capillarytube of the cube size control is routed out of the control box into its bulb holder on the evaporator coil. It is arevers...

Page 9 - Component Location ICEU060

Page 10 - Freezing Cycle

How It Works ICEU060 Page 9 Water System Freezing Cycle The refrigeration process creates cold temperatures within the evaporator coils and removes heat from thewater sprayed up into the inverted ice cube cups. When enough heat is removed, the water changes intoice, and forms where it is the coldest...

Page 12 - Harvest Cycle

How It Works ICEU060 Page 11 Refrigeration System Harvest Cycle (When the cubes are released) The ice cubes have been formed in an inverted mold that was refrigerated. Now the refrigeration systemwill change to warm the cube mold and release the cubes. The process begins at the compressor . There, r...

Page 13 - Operation and Adjustment ICEU060; Refrigeration System Pressures:; Adjustment Of The Cube Size; Adjust only when cubes are too large or too small.; Adjustment Of The Bin Thermostat Control; To increase the ice level in the storage bin:

Operation and Adjustment ICEU060 Page 12 The information shown below covers a wide range of air and water temperatures. It is intended as aguideline only, and is based on data compiled from NEW Clean units. Allow a variation from each end ofthe range given. Refrigeration System Pressures: Freeze Cyc...

Page 14 - Sanitizing And Cleaning ICEU060

Sanitizing And Cleaning ICEU060 Page 13 An Ice-O-Matic ice machine represents a sizable investment of time and money in any company’s business.In order to receive the best return for that investment, it MUST receive periodic maintenance. It is the USER’S RESPONSIBILITY to see that the unit is proper...

Page 15 - Service Diagnosis ICEU060; SYMPTOM

Service Diagnosis ICEU060 Page 14 SYMPTOM POSSIBLE CAUSE SUGGESTED CORRECTION Unit will not run. Blown fuse or breaker . Replace fuse and check for cause ofblown fuse or breaker. Compressor cyles Low voltage. Check voltage at the supply to the intermittenly. building.Check circuit for overloading. D...

Page 16 - Component Replacement ICEU060; Bin Thermostat; Replace with a new control in reverse order of removal.; Cube Size Control

Component Replacement ICEU060 Page 15 Bin Thermostat 1. Unplug the icemaker to disconnect electrical power.2. Remove screws and cabinet front panel.3. Remove screws and the control box cover, disconnect electrical wires from the bin thermostat control.4. Dismount the bin thermostat from the control ...

Page 17 - Spray Platform; Reverse removal procedures to replace.

Component Replacement ICEU060 Page 16 Spray Platform 1. Unplug the icemaker to disconnect electrical power.2. Open ice bin door.3. Pull out on the left side and remove curtain assembly.4. Lift the spray platform up and pull out to get to the water hose at the base of the platform.5. Pull hose off of...

Page 18 - Component Layout ICEU060

Page 19 - Wiring Diagram ICEU060