Page 3 - Contents; Reader’s Comments — We’d Like to Hear From You .; iii
Contents About This Book . . . . . . . . . . . . . . . . . . . . . . . v ISO 9000 . . . . . . . . . . . . . . . . . . . . . . . . . . v Online Publications . . . . . . . . . . . . . . . . . . . . . . . v Related Publications . . . . . . . . . . . . . . . . . . . . . . v Trademarks . . . . . . . . . ...
Page 4 - iv
iv Supplement to the Service Guide and User’s Guide
Page 5 - About This Book; Online Publications; Trademarks
About This Book This supplement provides updates to the following publications: v RS/6000 7043 43P Series User’s Guide , SA38-0511 v RS/6000 7043 43P Series Service Guide , SA38-0512 ISO 9000 ISO 9000 registered quality systems were used in the development and manufacturingof this product. Online Pu...
Page 7 - Identifying the Fansink Number; Determining the Fansink Assembly Number to be Replaced; Table 2. Fansink numbers by System Board Assembly and FRU Numbers.
Chapter 1. 7043–140 and 7043–150 Fansink Removal andReplacement Procedures This chapter provides information on replacing defective 7043–140 and 7043–150fansinks without having to replace the entire system board. Identifying the Fansink Number The following table contains information to help you det...
Page 8 - Removing and Replacing the 7043–140 System Board Fansink; FRU
Table 2. Fansink numbers by System Board Assembly and FRUNumbers (continued). Machine Type FRU Part Numbers System BoardAssembly PartNumbers Fansink Number 7043–150 375MHZNew Version SystemBoard 08L8446, 11K0157,11K0459 41L5177,41L5912, 41L551841L5590 03N2526, 08L1363,11K0148 11K0464,41L5172, 41L551...
Page 9 - Do not
4. To remove the disk drive bracket, refer to the ″ Removing Internal Drive ″ section of the RS/6000 7043–43P Series Service Guide . Carefully place the bracket assembly on top of the power supply (leave the hard files plugged in). Note: Disconect temporarily any PCI Adapter Card installed in slot 5...
Page 10 - Replacement; OR; Removing and Replacing the 7043–150 System Board Fansink
Replacement 1. If you are replacing a fansink 09P1125, install the new component by hooking the side opposite the finger tab and then pushing the finger tab side down until it locksinto position. OR If you are replacing a fansink 09P1126, first remove the paper pull tab to expose thethermal grease u...
Page 11 - no less than 30 seconds after powering off the system
5. Locate and unplug the fan and disconnect the fansink assembly power cable from the CPU fansink connector (J26). Note: There are two possible fansink connections for this system board: right-angle finger tabs, and wire springs. Fansink Location 6. To remove a fansink with right-angle finger tabs, ...
Page 15 - Setting the SCSI Security Jumpers
Setting the SCSI Security Jumpers Note: Carefully read and follow the safety guidelines detailed in the corresponding section of the RS/6000 7043 43P Series User’s Guide , SA38-0511. To increase system unit security, the external SCSI connector can be disabled bychanging jumpers inside the system un...
Page 16 - System Board Locations for Model 150
System Board Locations for Model 150 B1 Battery connector J1 Wakeup-on-LAN jumper J2 5x5 Auxiliary 5v connector J3 Audio input connector J4 Internal SCSI connector #2 J5 CD-ROM audio connector J6 CD-ROM audio connector J7 Power connector J8 Power connector J10 Media fan connector J11 Memory Connecto...
Page 23 - Reader’s Comments — We’d Like to Hear From You; Overall how satisfied are you with the information in this book?; Thank you for your response. May we contact you?
Reader’s Comments — We’d Like to Hear From You Supplement to the RS/6000 7043 43P Series Service Guide and User’s Guide Order Number: SN32–9080–01 Overall how satisfied are you with the information in this book? Very Satisfied Satisfied Neutral Dissatisfied Very Dissatisfied Overall Satisfaction h h...
Page 24 - Information Development; BUSINESS REPLY MAIL
Fold and Tape Fold and Tape Please do not Staple Please do not Staple Fold and Tape Fold and Tape Information Development Department H6DS-9561 11400 Burnet Road Austin, TX 78758-3493 Cut or Fold Along Line Cut or Fold Along Line BUSINESS REPLY MAIL NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES...
Page 26 - IBMR
IBMR Part Number: 09P2506 Printed in the United States of Americaon recycled paper containing 10%recovered post-consumer fiber. December 2000 SN32-9080-01 (1P) P/N: 09P2506