IBM L191p - Manual

4 2. Lift the monitor by placing your hands where indicated below. 3. Before using your monitor for the first time, remove the clear protective film from the front of the screen. Workplace Preparation This section gives advice on what you should consider before you set up your monitor. Height Positi...

5 DE UTSCH E N GLI S H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Adjusting the Monitor Position Viewing Angle You can tilt the screen backward and forward, swivel left or right as well as lift up and down as shown below. Working Practices This section gives advice on how you can wo...

6 Eyesight Working with monitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly. Screen settings Set the screen brightness and contrast to a comfortable level. You may have to adjust this as the lig...

7 Connecting your Monitor for Analog Be sure to read the ‘Safety Information’ at the front of this User Guide before carrying out this procedure. 1. Turn off your computer and all attached devices. 2. Connect the signal cable to the video port on the back of your computer. This port might be directl...

8 Connecting your Monitor for Digital 1. Turn off your computer and all attached devices. 2. Tilt monitor all the way forward. 3. Connect the DVI connector at the end of the DVI-D signal cable (shipped with your Monitor) to the DVI port located on the back of the Monitor. See picture below. Connecti...

9 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR 4. Connect the DVI connector at the other end of the signal cable to the DVI port located on the back of the graphics adapter. See picture below. 5. Connect the power cord to the power port on the back of your monitor i...

10 Device Driver Installation Use the User's Guide and Installation Files CD that comes with your monitor to install the appropriate device driver for your operating system. Installing the Windows XP device driver To manually install or update the device driver for the Microsoft ® Windows ® XP opera...

11 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR 7. Click Next> , Next> , and then Finish to complete the installation. 8. Close the Display Properties window. 9. Remove the User’s Guide and Installation Files CD from the computer CD-ROM drive. Installing the W...

12 1. Click Start Settings Control Panel and then double-click Display . 2. In the Display Properties window, click the Settings tab, and then click Advanced . 3. Click the Monitor tab, and then click Change . 4. When the Update Device Driver Wizard window opens, follow the steps in the previous par...

13 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR 4. In the Select Device window, click Have Disk . 5. Insert the User’s Guide and Installation Files CD into the computer CD- ROM drive, type d:\ (change the drive letter to match your CD-ROM drive if it is not drive D)...

14 Auto Image Setup (Analog Only) Auto Image Setup The Setup Utility included on the setup diskette is for displaying dot patterns. They do not replace or modify the display driver. The Auto Image Setupinstructions require the monitor to be warmed up for 15 minutes. This is not required for normal o...

15 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Auto Image Setup for DOS To optimize the displayed image automatically in DOS, do the following: If the monitor is in standby mode (STANDBY ON), it may automatically turn off while you are waiting for it to warm up. If...

16 Auto Image Setup for Windows 3.1, Windows 95, Windows 98, Windows NT, Windows 2000, Windows Me or Windows XP To optimize the displayed image automatically in Windows 3.1 , Windows 95, Windows 98, Windows NT, Windows 2000, Windows Me, or Windows XP, do the following: If the monitor is in standby m...

18 Manual Image Setup Normally, you can complete the setup procedure using A UTO I MAGE S ETUP ; however, if your screen image is still distorted after you perform A UTO I MAGE S ETUP or the Installation CD does not run on your system, perform M ANUAL I MAGE S ETUP . If the monitor is in standby mod...

19 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Adjusting Your LCD Monitor User controls User control features • Direct access controls • Main OSD menu controls Icon Control Description OSD Input Change Switches the video input source. Inactive Image Setup Activates...

20 Operation The image is already optimized for many display modes; however the user controls can be used to adjust the image to your liking. • Press the OSD Enter button to display the main OSD menu. • Use the Arrow buttons to move among the icons. Select an icon and press OSD Enter to access that ...

23 Options Information Shows resolution, refresh rate, and product details. Note: This screen does not allow any changes to the settings. Same as Analog Language The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Select one of the 5 la...

25 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Further Information Display modes The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes.The image size, position and...

26 For image problems, you may want to run AUTO Setup again before consulting to this section. In most cases, AUTO SETUP can fix the problems. See Auto Image Setup for DOS on page 15 for details. Factory Set Display Modes † Recommended ‘Note: VESA timings are as detailed in the VESA “Display Monitor...

27 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Power Management If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT m...

28 Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem Possible Cause Suggested Action Reference Computer does not boot after the g...

31 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Further Help If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM HelpCenter ® . In the US call 1-800-IBM-SERV (800-426-7378) In Canada (Toronto Only) call 416-383-3344 ...

32 Specifications This color monitor (Type-model 9419-Hx7) uses a 19-inch TFT LCD Dimensions A. Lower Position Height : Depth : Width : B. Higher Position Height : Depth : Width : Weight Unpackaged: Packaged: Tilt / Swivel / Lift Tilt: Swivel: Lift : – 0° / + 30° – 135° / + 135° Image Viewable Image...

34 Service Information The following parts are for use by IBM service, or IBM authorized dealers, to support the customer warranty. Parts are for service use only . Model Type 9419 73P3890 9419-HB7,HK7 Monitor - Business Black 73P3891 9419-HG7 Monitor - Ash Grey 73P3893 9419-HB7, HG7, HK7 Stand - Bu...

35 DE UTSCH EN GLIS H FRAN ÇAIS ESP AÑOL IT A L IANO JAP A NESE COMPL & W ARR Notices and Trademarks This section contains information on notices and trademarks. Notices IBM may not offer the products, services, or features discussed in this document in all countries. Consult your local IBM repr...

36 Trademarks The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other countries, or both:HelpCenter IBME NERGY S TAR® is a U.S. Govt. registered trademark. Microsoft ® Windows ® , and Windows NT are trademarks of Microsoft Cor...