IBM 8485 - Manual

Chapter 5. Solving problems . . . . . . . . . . . . . . . . . . . 49 Diagnostic tools overview . . . . . . . . . . . . . . . . . . . . . 49 POST beep codes . . . . . . . . . . . . . . . . . . . . . . . 49 POST error codes . . . . . . . . . . . . . . . . . . . . . . . . 50 ServerGuide problems . . . ...

Safety Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Lees voordat u dit produc...

Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a ...

Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery con...

Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts ...

Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a prob...

Statement 15: CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended. WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause ...

Chapter 1. Introduction This Installation Guide contains instructions for setting up the IBM ® xSeries ® 206m Machine Types 8485 and 8490 servers and basic instructions for installing some options. More detailed instructions for installing options are in the User’s Guide on the IBM xSeries Documenta...

order of the most occurrences. Click a document to view it, and press Crtl+F to use the Acrobat search function or Alt+F to use the xpdf search function within the document. Click Help for detailed information about using the Documentation Browser. Notices and statements in this document The caution...

Installing a memory module The following notes describe the types of dual inline memory modules (DIMMs) that the server supports and other information that you must consider when installing DIMMs: v The server supports industry-standard, 533/667 MHz, PC2-4200, double-data-rate 2 (DDR2) dual inline m...

7. Pull the loops of the drive assembly toward each other; then, carefully slide the drive assembly into the drive bay until it stops and release the loops. Note: Do not release the loops on the drive assembly until it is completely seated. 8. Attach the signal cable to the drive: a. Attach one end ...

– (Optional) Diskette drive: The narrower signal cable has two connectors. One is attached to the diskette drive, and the other is connected to the connector (FDD1) on the system board. – SATA: The narrower, black signal cable has two connectors. One is connected to the non-hot-swap SATA drive, and ...

Chapter 3. Server controls, LEDs, and power This chapter describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off. Front view The following illustration shows the controls, LEDs, and connectors on the front of the server. CD-eject or DVD-eject button CD or DVD dr...

Viewing the configuration: To view information about the SATA controller, complete the following steps: 1. Start the Array Configuration Utility. 2. From the Array Configuration Utility window, select Manage Arrays . 3. Select an array and press Enter. 4. Press Esc to exit from the program. Chapter ...

Table 2. Abbreviated list of POST error codes (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceab...

Optional-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which componen...

System-board LEDs The following illustration shows the LEDs on the system board. You might need to refer to this illustration when solving problems with the server. Note: The server does not contain a light path diagnostics panel. System fan 3 error (LED2) System fan 1 error (LED3) System fan 2error...

Appendix B. Notices This information was developed for products and services offered in the U.S.A. IBM may not offer the products, services, or features discussed in this document in other countries. Consult your local IBM representative for information on the products and services currently availab...

Trademarks The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: Active Memory Predictive Failure Analysis Active PCI PS/2 Active PCI-X ServeRAID Alert on LAN ServerGuide BladeCenter ServerProven C2T Interconnect TechConnect...

applicable throughout the European Union. This label is applied to various products to indicate that the product is not to be thrown away, but rather reclaimed upon end of life per this Directive. Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne et à la Norvège. L’etiquet...

Electronic emission notices (Class B) IBM Eserver xSeries 206m Types 8485 and 8490 Important: The notices in this section apply to xSeries 206m servers that contain non-hot-swap power supplies. Federal Communications Commission (FCC) statement Note: This equipment has been tested and found to comply...

Index A acoustical noise emissions 5 Adaptec RAID Configuration Utility 42 adapter installing 26 requirements 25 scanning order 26 specifications 5 support bracket 6 Array Configuration Utility 42 arrays, using ServeRAID Manager 45 attention notices 4 B backplane 19, 21 battery return program 82 saf...