IBM 02L1333 - Manual
IBM 02L1333 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – LAN S; Configuring the ATM Module; Access the Local Management Screens; Figure 1; ATM Module Configuration Screen; Ensure that the Default VLAN is operational; Figure 2; Switch Management Screen; In the
- Page 3 – ATM VLAN LEC Status Screen; LEC State
- Page 4 – Troubleshooting
- Page 5 – Menu Map; Figure 4; ATM Module Screen Map
Part No. 02L1333
Published October 1997
8271 N
WAYS
E
THERNET
LAN S
WITCH
ATM OC-3
C
M
ODULE
Q
UICK
R
EFERENCE
G
UIDE
Pre-Configuration Checklist
Before configuring the ATM OC-3c Module, com-
plete the following steps:
1
Install the ATM Module —
Installation instruc-
tions are provided in “Installing and Setting Up the
Module” in the ATM Module User’s Guide.
2
Check that the ATM Module is correctly
installed in the Switch —
Follow the “Post Instal-
lation Checks” as described in “Installing and Set-
ting Up the Module”, in the ATM Module User’s
Guide.
3
Check that the Switch is correctly installed in
the network —
See the User’s Guide that came
with your Switch.
In this reference guide, the term Switch is used to
identify the device containing the ATM Module.
The term ATM Switch is used to identify the ATM
device that the Switch is connected to on the net-
work.
4
Ensure that the LANE Services are correctly set up
on your network, that is, each LAN Emulation Server
(LES) and its associated Broadcast and Unknown
Server (BUS) are operational.
5
To communicate with an ATM Switch, the communi-
cation settings on the ATM Module and ATM Switch
must be compatible. Find the following ATM Switch
settings and enter them below:
Signalling Mode
Signalling must be the same on both devices, and
must be either 3.0 or 3.1. The default on the ATM
Module is 3.1.
SONET or SDH?
Both devices must use the same physical standard.
The ATM Module supports
SONET STS-3c
and
SDH
STM-1
, and the default is
SONET STS-3c
.
Both devices must use the same
Interim Local Management Interface (ILMI)
connection.
The default is VPI = 0 and VCI = 16.
ILMI VCC
VPI =
VCI =
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 8271 N WAYS E THERNET LAN S WITCH ATM OC-3 C M ODULE Q UICK R EFERENCE G UIDE Configuring the ATM Module 1 Access the Local Management Screens Refer to “Accessing Management Features” in the ATM Module User’s guide for instructions. 2 Ensure that the ATM Module and ATM Switch use compatible settin...
Configuring the ATM Module 3 c Ensure that the Port ID is set to the ATM port number. The ATM port numbers are as follows: Q Port 13 on an IBM 8271 Nways Ethernet LAN Switch Model 612 and IBM 8271 Nways Ether-net LAN Switch Model 712 Q Port 25 on an IBM 8271 Nways Ethernet LAN Switch Model 624 and I...
4 8271 N WAYS E THERNET LAN S WITCH ATM OC-3 C M ODULE Q UICK R EFERENCE G UIDE Troubleshooting The most likely error at start-up time is a problem with the physical connection. Use Table 1 to iden-tify any problems you encounter after installation. If you cannot resolve the problem using the table,...
