Husqvarna Viking Huskylock 905 - User Manual

–9– —5— 1-4. Sewing speed The harder you press the foot control, the faster the machine will run. You can choose between two sewing speeds with the speed selector. :0-1000 (max. speed 1000 stitches/min) :0-1300 (max. speed 1300 stitches/min) 1-5. Telescopic thread stand EXtend the telescopic thread ...

–10– B A —6— 1-7. Changing threads The machine comes threaded with overlock thread. To change thread follow the easy thread ing as explained on page 8~10 or to tie on: 1. Cut the thread in use near the thread spool (behind the telescopic thread stand). Place the new thread spool on the spindle and t...

–13– 1 2 3 4 D N D N C D A B 6 5 7 8 9 10 —9— Lower looper threading ( B ) 1. Raise the presser foot. 2. Open front cover. 3. Pull thread from spool through guide 1 of the thread stand and then through guide 2 . Note: Make sure the thread snaps into the slot of guide 2 , and between the thread ten- ...

–11– —11— Presser foot pressure You can change the presser foot pressure with the graded dial on the left side of the ma chine. Position “N” is for normal fabrics. A lower number is for thin fabrics. A higher number is for thick fabrics. 1-9. Thread tension table The thread tension is only a recomme...

–12– 2 3 4 1 —12— 1-10. Thread tension Start from normal position. Change and there af ter check one dial at a time until you obtain the desired result. Turn the dial to a higher number to increase tension. Turn the dial to a lower number to decrease tension. ➀ Left needle thread ➁ Right needle thre...

–17– —17— 2-2. Choice of languageYou can select the following languages: American English, Britich English, French, Italian, German, Swedish, Norwegian, Danish, Finnish, Dutch, Spanish, Czech, Polish, Japanese. Select the language as follows:1. Turn on the machine while pressing the A-key and the Cu...

–19– —19— Store new numbersIncrease the set number by pressing the (+) key and reduce the set number by pressing the (-) key. Continue pressing the (+) or (-) key until the desired numbers appear. Note: To save this setting, store it in Memory Mode. 2-8. : Memory Mode After making new settings in Ma...

–22– —22— Chain off When you reach the end of the fabric, chain off for several inches. Note: Do not pull the threads out roughly, be- cause the needle might bend or break. • Cut off the thread chain using the thread cut- ter on the left of the machine. Note: Lay thread chain into thread cutter from...

–23– —23— Cording thread / Decorative thread Cording thread / decorative thread can be used to strengthen and stabilize stitches when seam- ing stretch fabrics. Listed below are two ways of using corded thread: • Thread cord through the loop at the extreme left of the telescopic stand and through th...

–24– —24— Serging curves For inside curves, guide the fabric lightly and place the fabric under the right front of the presser foot. Applying pressure to the fabric with your left hand at the same time, apply a little pressure in the opposite direction with your right hand to hold it against the cut...

–25– 2 1 2 1 —25— 3-2. Three thread overlock To sew three thread overlock, simply remove one needle. 1. Remove the right needle for wide three thread Use dial 1 for the tension of the left needle thread, stitch width/cutting width is normally 6 mm. The differential feed ratio is normally “N”. 2. Rem...

–26– —26— 2-Thread converter Accessory box 3-3. Two thread overlock (Model 905) 1. Use one needle thread (left or right needle) and lower looper thread. 2. Take out the 2-Thread converter for the up- per looper from the accessory box. 3. Open the front cover. Make sure that the upper looper is to th...

–28– 2.5~3mm —28— Material guide Adjusting screw Right side of fabric A. B. C. 3-4. Flatlock There are two ways to sew a Á atlock stitch, with wrong sides folded together to create a dec o - ra tive look and with right sides folded together to create ladder stitch as used for lingerie. 1. Fold the m...

–30– —30— 3-6. Rolled edge Three thread rolled edge Narrow edging rolled edge The fabric is overlocked with upper and lower looper. The fabric is rolled by adjusting the thread tension and is overlocked with upper looper thread. The two edges described above are suitable for lightweight fabrics. 1. ...

–31– —31— Table for three thread rolled edge and narrow edge Adjust as needed according to type of fabric and thread. Two thread rolled edge 1. Convert to 2-thread overlock, see page 26-27 2. Use right needle only and pull stitch À nger lever toward you to align with “R” on the stitch plate. Thread ...

–32– —32— 3-7. Pin tuckPin tucks are stitched along a folded edge. To avoid cutting the fabric, use the multipurpose foot. Pin tucks are suitable for children’s clothes and lady’s blouses.1. Use the left needle for wide tucks, the right needle for narrow. 2. Snap on multipurpose foot and adjust guid...

–36– —36— 5. STITCH TABLE LCD Data reference sheet (For 4thread model) Combination Thread tension Sewing Program Material Woven Med N N N N 4Thread Woven Hvy N N N N N Woven Lt N N N CD N N N N Knit Med 1.5 3 N N N Knit Hvy 2.0 3 N N N Knit Lt N 3 N N N Overlock Woven Med N - N N 3Thread Woven Hvy N...

–39– —39— 6. TABLE OF SEWING MATERIALS, NEEDLES AND THREADS Use ball point needles for stretch fabrics. Thin materials (crepe, georgette) Thick materials (thick denim) Medium materials (chino, gabardine, etc.) Twisted thread #50/2~#60/2 Twisted thread #60/2 Medium Stitch length Tight Loose Overedgin...

VSM Group AB • SE-561 84 Huskvarna, Sweden www.husqvarnaviking.com 412 85 75-26B • © 2006 VSM Group AB • All r ights reser ved • Pr inted in Sw eden on en vironmentall y-fr iendl y paper