Husqvarna Automower 440 - User Manual

2 Introduction 2.1 Introduction Serial number: Product number: PIN code: The serial number and the product number are on the product rating plate and on the product carton.• Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchas...

2.2 Product overview Automower 420/440 Automower 430X Automower 450X 23 22 28 24 25 27 26 21 31 32 30 29 4 5 2 3 1 19 20 9 11 10 12 13 14 15 16 17 6 7 8 18 The numbers in the figure represent:1. Body 2. Hatch to display and keypad 3. Stop button 4. Front wheels 5. Rear wheels 6. Ultrasonic sensors 7...

2.7 Menu structure overview 1 Security Low Medium High Custom Duration Durationof alarm Durationof time lock ChangePIN code New loopsignal Security level Faultmessages Infomessages Messages Advanced Schedule Overview (per day) Overview Schedule settings Cutting height Cutting height TargetHeight Per...

2.8 Menu structure overview 2 Use Low Medium High Cutting time Weather timer Installation Lawncoverage GPS Auto430X/450X Overview oflawn coverage Area 1-5 Find charging station Overview of search method Guide Delay time Test Reset Testleft Testright Reset Disable Delay time More Disable More Boundar...

2.9 Menu structure overview 3 Settings ECO mode Use Profiles Select Rename Save Profile A,B or C Time &date Set time Set date Time format Date format Language Country & Timezone Reset alluser setting About Low Low- High High+ Medium Intensity l a r e n e G g n i t t u c l a r i p S Use Use H...

3 Installation 3.1 Introduction - Installation WARNING: Read and understand the safety chapter before you install the product. CAUTION: Use original spare parts and installation material. Note: Refer to www.husqvarna.com for more information about installation. 3.2 Main components for installation T...

B A • Put the boundary wire around the secondary area (B) to make an island. Refer to To make an island on page 17. Note: The boundary wire must be put as 1 loop around all of the work area (A + B). Note: When the product cuts grass in the secondary area, the Secondary area mode must be selected. Re...

B D C A 3.5 Installation of the product 3.5.1 Installation tools • Hammer/plastic mallet: To simplify putting the stakes into the ground. • Edge cutter/straight spade: To bury the boundary wire. • Combination pliers: For cutting the boundary wire and pressing the connectors together. • Adjustable pl...

CAUTION: Cutting the grass too low right after installation can damage the wire insulation. Damage to the insulation may not cause disruptions until several weeks or months later. 1. Put the boundary wire and the guide wire on the ground. 2. Put the stakes at a maximum of 75 cm / 30 in. distance fro...

4 Product settings You can use the keypad and the display on the product or the Automower ® Connect app to do the settings for the functions of the product. The functions of the product have factory settings that are applicable for almost all work areas, but the settings can be adapted to the condit...

5 Operation 5.1 Main switch WARNING: Read and understand the safety chapter before you use the product. • Set the Main switch to the 1 position to start the product. • Set the Main switch to the 0 position to set the product to OFF. 5.2 To start the product 1. Push the STOP button to open the hatch ...

6 Maintenance 6.1 Introduction - maintenance WARNING: The product must be switched off before any maintenance is done. WARNING: Wear protective gloves. For better operation and longer service life, make sure to clean the product regularly and replace worn parts. All maintenance and servicing must be...

6.3 Replacement of the blades WARNING: Husqvarna can only guarantee safety if you use Husqvarna original blades with the embossed crowned H-mark logotype. WARNING: You must replace the screws when you replace the blades. The used screws can wear quickly and make the blade come loose, this can cause ...

7 Troubleshooting 7.1 Introduction - troubleshooting In this chapter you can find information and help about faults and symptoms of the product. You can find more information and FAQ (Frequently Asked Questions) on www.husqvarna.com. 7.2 Fault messages The list below shows a number of fault messages...

Message Cause Action Zone generator prob- lemFlexiFence problem The battery of the FlexiFence accessory is low. The FlexiFence accessory does not op- erate when the battery is empty. The product can cut in the stay-out zone if you start the product before you charge the FlexiFence accessory. Park th...

Message Cause Action SIM card requires PIN The SIM card must be unlocked. Make sure the correct SIM PIN has been entered into the mower's menu (Network > SIM card). Contact your local Husqvarna rep- resentative if this message appears often. SIM card locked The SIM card must be replaced. Contact ...

Symptoms Cause Action The product is parked for hours in the charging station. The hatch is closed but the START button is not pushed. Push the STOP button to open the hatch. Enter the PIN code and confirm with the OK button. Push the START button and then close the hatch. Parking mode is activated....

8 Transportation, storage and disposal 8.1 Transportation The supplied Li-ion batteries obey the Dangerous Goods Legislation requirements.• Obey all applicable national regulations. • Obey the special requirement on package and labels for commercial transportations, including by third parties and fo...

9 Technical data 9.1 Technical data Dimensions Automower ® 420 Automower ® 430X Automower ® 440 Automower ® 450X Length, cm / in. 72 / 28.3 72 / 28.3 72 / 28.3 72 / 28.3 Width, cm / in. 56 / 22.0 56 / 22.0 56 / 22.0 56 / 22.0 Height, cm / in. 31 / 12.2 31 / 12.2 31 / 12.2 31 / 12.2 Weight, kg / lbs ...

Power Class Bluetooth ® Output power 8 dBM Automower ® Connect 2G Power Class 4 (GSM/E-GSM) 33 dBm Power Class 1 (DCS/PCS) 30 dBm Power Class E2 (GSM/E-GSM) 27 dBm Power Class E2 (DCS/PCS) 26 dBm Automower ® Connect 3G Power Class 3 24 dBm Automower ® Connect 4G Power Class 3 23 dBm Husqvarna AB doe...