Page 2 - Intended use; Product description; Product overview
Contents Introduction..................................................................... 2 Safety..............................................................................3 Assembly...................................................................... 12 Operation.................................
Page 3 - Safety; Safety definitions
17. Spiked bumper18. Bar tip sprocket19. Saw chain20. Guide bar21. Chain catcher22. Chain tensioning screw23. Drive sprocket cover (536 LiXP)24. Charging LED25. Warning indicator26. Power cord27. Combination wrench28. Battery charger29. Button, battery status30. Battery status31. Warning indicator32...
Page 4 - General power tool safety warnings; Work area safety
CAUTION: Damage to the product. Note: This information makes the product easier to use. General power tool safety warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Note: Save all ...
Page 10 - Battery safety
brake. If a kickback occur when you use the product, hold tight around the handles and do not let go. The front hand guard also decreases the risk to hit the saw chain if your hand lets go of the front handle. In the felling position you can not engage the chain brake manually. The chain brake can i...
Page 11 - Safety instructions for the cutting equipment
• Do not let battery acid touch your skin. Battery acid causes injuries to the skin, corrosion and burns. If you get battery acid in your eyes, do not rub but flush with water for minimum 15 minutes. If battery acid has touched your skin, you must clean the skin with a large quantity of water and so...
Page 12 - Assembly; To assemble the guide bar and saw
• Keep the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback. • Make sure that the saw chain has the correct tension! If the saw chain is not tight against the guide bar, the risk for it to come lo...
Page 14 - Operation; To do a function check before you use
Operation To do a function check before you use the product 1. Do a check of the chain brake to make sure that it operates correctly and that it is not damaged. 2. Do a check of the rear right hand guard to make sure that it is not damaged. 3. Do a check of the power trigger lockout to make sure tha...
Page 17 - Common questions about kickback; To use the cutting technique
the kickback occurs that causes the direction of movement. Kickback only occurs if the kickback zone of the guide bar touches an object. Do not let the kickback zone touch an object. The smaller the bar tip radius the lower the risk of kickback.A saw chain is made up of a number of links, which are ...
Page 19 - To cut a trunk with support on two ends; To use the limbing technique
1. Cut on the push stroke approximately 1/3 through the trunk. 2. Cut through the trunk on the pull stroke until the two kerfs touch. To cut a trunk with support on two ends WARNING: Follow the steps below to prevent the saw chain from getting trapped in the trunk. 1. Cut on the pull stroke approxim...
Page 20 - To use the tree felling technique; To keep a safe distance
To use the tree felling technique WARNING: You must have much experience to fell a tree. Operators without experience must not fell trees. To keep a safe distance 1. Make sure that persons around you keep a safe distance at a minimum of 2 1/2 tree lengths. 2. Make sure that no person is in the risk ...
Page 21 - To fell a tree
1 2 2 1 1 3 To fell a tree You use three cuts to fell a tree. These are the directional cuts, which include the top cut and the bottom cut, and the felling cut. If you make these cuts correctly, you can control the felling direction very accurately. WARNING: Do not fell trees with a diameter larger ...
Page 23 - Maintenance; Introduction; To do a check of the front hand guard
4. Keep a position where the tree or branch can not hit you when the tension is released. 5. Make one or more cuts of sufficient depth necessary to decrease the tension. Cut at or near the point of maximum tension. Make the tree or branch break at the point of maximum tension. WARNING: Do not cut st...
Page 25 - Information about the guide bar and saw chain
3. Make sure that the product stops when you press and hold the button. The green LED will go off. To do a check of the battery and the battery compartment 1. Clean the battery and the battery compartment with a soft brush. 2. Make sure that the cooling slots and battery connectors are clean. 3. Mak...
Page 28 - To tighten the saw chain
We recommend that you use our depth gauge tool to receive the correct depth gauge setting and bevel for the depth gauge. 1. Use a flat file and a depth gauge tool to adjust the depth gauge setting. Only use Husqvarna depth gauge tool to receive the correct depth gauge setting and bevel for the depth...
Page 31 - Maintenance schedule; Troubleshooting; Troubleshooting schedule
Maintenance schedule WARNING: Remove the battery before you do maintenance. The following is a list of the maintenance steps that you must do on the product. See Maintenance on page 23 for more information. Maintenance Before use Weekly Monthly Clean the external parts of the product. X Make sure th...
Page 32 - Transportation, storage and disposal; Transportation and storage
LED display Possible faults Possible action Warning indicator flashing. Chain brake engaged. Pull back the front hand guard to re- lease the chain brake. Temperature deviation. Allow the product to cool down. Overload. Cutting attachment jam- med. The cutting attachment is jammed. Release the cuttin...
Page 33 - Technical data
• Obey the special requirement on package and labels for commercial transportations, including by third parties and forwarding agents. • Speak to a person with special training in dangerous material before you send the product. Obey all applicable national regulations. • Use tape on open contacts wh...
Page 34 - Accessories; Guide bar and saw chain combinations
436 Li 536 LiXP Sound levels 2 Equivalent sound pressure level at the operator's ear, dB(A) 93 93 Vibration levels 3 Front handle m/s 2 3,5 4,1 Rear handle m/s 2 3,9 4,6 Equivalent vibration levels 4 Front handle m/s 2 2,2 2,5 Rear handle m/s 2 2,4 2,8 Saw chain/guide bar Recommended bar lengths, in...
Page 35 - Approved batteries for the product; Approved battery chargers for the product
38 11/64 in/4,5 mm 90° 30° 0° 0.025 in/ 0,65 mm 5056981-03 5795588-01 Approved batteries for the product Battery BLi110 BLi150 Type Lithium-ion Lithium-ion Battery capacity, Ah 3,0 4,2 Nominal voltage, V 36 36 Weight, kg/lb 1,2/2.6 1,3/2.9 Approved battery chargers for the product Battery charger QC...
Page 36 - EC Declaration of Conformity; EC Declaration of conformity
EC Declaration of Conformity EC Declaration of conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the cordless battery chainsaws Husqvarna 436 Li and 536 LiXP from 2016’s serial numbers and onwards (the year is clearly stated in plain te...
