Page 2 - CONTENTS; Contents
2 CONTENTS Contents CONTENTS Contents 2 . . . . . . . . . . . . . . . . . . . . . . . . Note the following before starting 2 . . . . KEY TO SYMBOLS Symbols 3 . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY INSTRUCTIONS Personal protective equipment 4 . . . . . . Machine’s safety equipment 4...
Page 3 - KEY TO SYMBOLS; Symbols
3 KEY TO SYMBOLS Only intended for trimmer heads. Other symbols/decals on the machine refer to special certification requirements for certain markets. Stop the engine by pushing and holding the stop switch in the STOP position until the engine stops before carrying out any checks or maintenance. Reg...
Page 4 - SAFETY INSTRUCTIONS; Personal protective equipment
4 SAFETY INSTRUCTIONS GLOVES Gloves should be worn when necessary, e.g., when fitting cutting attachments. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protec...
Page 6 - Throttle lock
6 SAFETY INSTRUCTIONS Throttle lock S Make sure the throttle control is locked at the idle setting when the throttle lock is released. S Press the throttle lock and make sure it returns to its original position when you release it. S Check that the throttle control and throttle lock move freely and ...
Page 7 - Trimmer head; General rules
7 SAFETY INSTRUCTIONS Trimmer head S Only use the recommended cutting at- tachments. See the section on “Technical data”. WARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any o...
Page 8 - General safety precautions
8 SAFETY INSTRUCTIONS General safety precautions IMPORTANT! S The machine is only designed for trimming grass. S The only accessories you can operate with this engine unit are the cutting at- tachments we recommend in the “Tech- nical data” section. S Never use wire, rope, string, etc. S Never use t...
Page 11 - KNOW YOUR TRIMMER
11 KNOW YOUR TRIMMER 1. Trimmer head 11. Starter handle 2. Grease filler cap 12. Fuel tank 3. Bevel gear 13. Choke control 4. Cutting attachment guard 14. Air purge 5. Shaft 15. Air filter cover 6. Loop handle 16. Handle adjustment 7. Throttle control 17. Drive disc 8. Stop switch 18. 2--stroke engi...
Page 12 - ASSEMBLY; itting the trimmer guard and
12 ASSEMBLY F itting the trimmer guard and trimmer head (Model 125L) S Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (D). Make sure unit is assembled correctly as shown in this manual. ...
Page 13 - FUEL HANDLING; Fuel
13 FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-- stroke engine and must always be run using a mixture of gasoline and two-- stroke engine oil. It is important to accu- rately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small am...
Page 14 - STARTING AND STOPPING; Check before starting; Never wrap the starter cord around
14 STARTING AND STOPPING Check before starting S Inspect the unit before each use. Re- place damaged parts. Check for fuel leaks. Make sure all fasteners are in place and secure. Make sure the cutting attachment is properly installed and se- curely fastened. Use only flexible, non- metallic line rec...
Page 15 - Warm engine; Stopping
15 STARTING AND STOPPING Warm engine With a warm engine, squeeze and hold the throttle trigger. Pull starter rope sharply while squeezing throttle trigger until engine runs. Stopping Stop the engine by pushing and holding the stop switch in the STOP position until the engine stops. WARNING! When the...
Page 16 - MAINTENANCE
16 MAINTENANCE The idle speed is correctly adjusted when the engine will run smoothly in every posi- tion. The idle speed should also be well below the speed at which the cutting at- tachment starts to rotate. Carburetor Your Husqvarna product has been designed and manufactured to specifications tha...
Page 17 - Air filter
17 MAINTENANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: S Carburetor malfunctions S Starting problems S Loss of engine power S Unnecessary wear to engine parts S Excessive fuel consumption Clean the filter every 25 hours, or more regularly if con...
Page 18 - Maintenance schedule
18 MAINTENANCE Maintenance schedule Below you will find some general mainte- nance instructions. Daily maintenance S Check throttle trigger and throttle trigger lockout function. S Check that the stop switch works correctly. S Check that there are no fuel leaks from the engine, tank or fuel lines. S...
Page 19 - Trimmer Head Line Loading Instructions
19 Trimmer Head Line Loading Instructions 20 i 10 i 3 m 6 m
Page 20 - TECHNICAL DATA; Technical data
20 TECHNICAL DATA Model 125L (M10 LH arbor shaft thread) Approved accessories Type Cutting attachment guard, part. no. Trimmer head T25 537 33 83--02 Plastic blades Tricut 300 mm 531 00 38--24 J--Handle kit (to equip unit for brush blade) 503 78 17--01 *Brush blade 537 14 95--01 Technical data 125C ...
Page 21 - WARRANTY STATEMENT
21 WARRANTY STATEMENT SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from de- fects in material and workmanship from the date of purchase for the “Warranty Period” of the products as set forth below: Lif...
Page 22 - EMISSION CONTROL WARRANTY STATEMENT
22 U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environmental Protection Agency, California Air Resources Board, Environment Canada and HUSQVARNA are pleased to explain the emissions control system warranty on your year...
Page 23 - MAINTENANCE, REPLACEMENT
23 U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION RE- LATED PARTS: Any HUSQVARNA approved replacement part used in the performance of any warran- ty maintenance or repair on emission re- lated parts will be provided with...
