Hubbell 670-801-EX - Manual
Hubbell 670-801-EX – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Hardware Configuration
- Page 4 – Figure 4. SmartSeries Amplifier-Side View
- Page 5 – Block Diagram
- Page 6 – Interfaces; EGND
- Page 7 – Installation; Mounting; Figure 6. Shows mounting holes with dimensions.
- Page 8 – UL Version; Feed the wiring through the conduit and into the enclosure.; EX Version; Follow the mounting instructions described above.
- Page 9 – Figure 7. Wiring Detail
- Page 10 – Operation; Adjustments; CAUTION; Minimum Level
- Page 11 – Offset Level; VLC Level; Internal Adjustments; FSK Transmit Level
- Page 12 – Maintenance; Troubleshooting
- Page 13 – Software Configuration; The unit has the following versions of software:; FSK modem PCBA
- Page 14 – Specifications; 6 k-ohms nominal with FSK modem
- Page 15 – Replacement Parts; Reference Material; Reference to Assembly/Model Drawings
Pub. 42004-615L2
GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA
610-777-1374
800-492-1212
Fax: 610-796-5954
V
ISIT WWW
.
GAI
-
TRONICS
.
COM FOR PRODUCT LITERATURE AND MANUALS
G A I - T R O N I C S ® C O R P O R A T I O N
A H U B B E L L C O M P A N Y
Model 670-801-EX and 670-801-UL
SmartSeries Amplifiers
for CENELEC Zone 1 and UL Div. 1
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
Introduction
The assembly described in this manual is an explosion-proof enclosure and intelligent speaker amplifier
designed to be installed in hazardous areas where combustible gases exist or may exist. The extra thick
cast aluminum enclosure, while not gas tight, is designed to withstand repeated internal explosions
without expelling gases hot enough to ignite the external atmosphere. This is accomplished through the
use of a precision-machined enclosure opening flame path that cools the exiting gases to a temperature
below the flash point of the external, explosive atmosphere.
How to Use the Assembly/Model
Application
The hazardous area SmartSeries amplifier
is designed to provide clear communications even in high noise
areas where explosive atmospheres exist or may exist.
The Model 670-801-EX is BASEEFA approved to CENELEC Standards Ex dib for Zone 1, Group IIC
T5.
The Model 670-801-UL is approved by Underwriters Laboratories for:
•
Class 1, Div. 1, Groups C and D
•
Class II, Div. 1, Groups E, F, and G
•
Class III, Div. 1
The intelligent SmartSeries
amplifier is designed for use on the GAI-Tronics single party or multi-party
system cable. It includes micro-controllers that are programmed to:
•
Receive and send data messages on the system cable
•
Measure ambient noise and adjust speaker level
•
Monitor and control optional external equipment
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Pub. 42004-615L2 Model 670-801-EX and 670-801-UL SmartSeries Amplifiers Page: 2 of 15 \\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-615l2.doc 6/97 Hardware Configuration The exterior view of the cast aluminum explosion-proof enclosure is shown in Figure 1 below: Figu...
Pub. 42004-615L2 Model 670-801-EX and 670-801-UL SmartSeries Amplifiers Page: 4 of 15 \\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-615l2.doc 6/97 Internal The SmartSeries amplifier contains the following components: • Chassis • Bias Power Supply sub-assembly fixed t...
Pub. 42004-615L2 Model 670-801-EX and 670-801-UL SmartSeries Amplifiers Page: 5 of 15 \\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-615l2.doc 6/97 Block Diagram Figure 5. Model 670-801 Block Diagram As shown on Figure 5, P1 is the 16-pin male connector located on the...
