Page 2 - JPEG2000 Stand alone DVR User Guide; CHAP.6 PTZ camera control
JPEG2000 Stand alone DVR User Guide - 2 - Disclaimer: The product names mentioned in this manual are used as identifications only, while the copyright of these names might belong to other companies. The product spec and info are for reference only, and they may be updated from time to time without n...
Page 3 - Caution
JPEG2000 Stand alone DVR User Guide - 3 - For you safety, unplug the power before moving the DVR, installing, or replacing any parts or hard drive. Make sure all the power cable and wires are properly set up before using the DVR. Contact your distributor immediately if there is any defect. To avoid ...
Page 4 - Model; Specification
JPEG2000 Stand alone DVR User Guide - 4 - Model 4/8/16 CH JPEG2000 Stand Alone DVR Video Input 4/8/16CH VIDEO IN 1.0 VP-P ， 75OHM(BNC TYPE) Video Output (BNC TYPE) X 2 Video I/O VGA Output Support TFT LCD Monitor (Optional) Audio Input 4 CH Audio Input (MONO type) Audio I/O (Optional) Audio Output 1...
Page 5 - Network
JPEG2000 Stand alone DVR User Guide - 5 - Protocol TCP/IP Network Remote monitoring Remote Softeware: Remote live view, playback, and save as AVI IE: Remote live view, backup, and save backup to AVI Back-up VCR, CD-R back-up, Backup via IE PTZ Control RS485 ， supports PELCO D and other protocols RS2...
Page 6 - -1 Front panel introduction
JPEG2000 Stand alone DVR User Guide - 6 - 1-1 Front panel introduction 1.[CD-RW] Built-in CD-RW for CD-R back-up. 2.[IR Receiver & LED Lamps] IR Remote Controller Receiver. DVR Status LED: RUN- Flashes when play picture by picture through J. Shuttle. ACTIVE- On when the J. Shuttle is ready to us...
Page 8 - -2 Back panel introduction
JPEG2000 Stand alone DVR User Guide - 8 - 1-2 Back panel introduction [4Channel] [8Channel] [16Channel] 1.[RS485, Relay Output, Sensor Input] RS485, for direct connection to PTZ cameras. 16 sensor inputs and 1 relay output. 2.[VGA Output] Connection to a VGA monitor or TFT LCD. 3.[ETHERNET] Connecti...
Page 9 - -3 IR remote controller introduction
JPEG2000 Stand alone DVR User Guide - 9 - 1-3 IR remote controller introduction 1.[MENU] Enter menu or exit 2.[Split /OSD] 4S: 4 split 9S: 9 split 16S: 16 split OSD: OSD words on/off 3.[1~16 Channel] Switch channel in live or playback; password entering 4.[Control function] FRZ- Freeze the screen in...
Page 10 - -1 Camera and monitor installation
JPEG2000 Stand alone DVR User Guide - 10 - 2-1 Camera and monitor installation 2-1-1 Camera installation Connect camera to DVR camera in CH1~CH16 ※ Please do not start the DVR before the camera. installation is done. 2-1-2 Monitor and VCR installation Monitor: Connect the MONTIOR port on the DVR bac...
Page 11 - -2 Sensor and alarm installation
JPEG2000 Stand alone DVR User Guide - 11 - 2-1-3 Loop out installation To monitor a single channel, connect the “loop out” of the corresponding channel to a monitor. To record a specific channel individually, connect the “loop out” of the corresponding channel to a DVR, VCR, or other record device. ...
Page 12 - -3 Network and serial port installation
JPEG2000 Stand alone DVR User Guide - 12 - 2-2-3 Relay output installation Alarm output can be NO or NC, depending on the settings. NO-COM: the NO and COM terminals are open-circuit, and it’ll become closed-circuit when alarm triggered. NC-COM: the NC and COM terminals are closed-circuit, and it’ll ...
Page 13 - DVMR unit
JPEG2000 Stand alone DVR User Guide - 13 - # 2 RxD # 3 TxD # 5 GND TxD # 3 GND # 5 RxD # 2 DVMR unit Other device (PC) D-SUB 9 cable ( twisted RS-232C cable) To connect DVR to a PC, users must use a twisted RS232 cable, as the illustration. 2-3-3 PTZ camera installation Please connect the PTZ’s D+ t...
Page 16 - -1 Display configuration
JPEG2000 Stand alone DVR User Guide - 16 - 3-1 Display configuration 1.[Time] Current system time or the recorded time in playback 2.[Date] Current system date or the recorded date in playback 3.[Camera title] Camera title of the displayed channel. Camera title can be modified in [SYSTEM MENU] f [CO...
Page 18 - -5 View in sequence
JPEG2000 Stand alone DVR User Guide - 18 - 3-4-2 Freeze in Full mode In full screen mode, Press FREEZE to freeze the channel, and press FREEZE again to cancel. 3-5 View in sequence Press SEQ to enter Sequential Switch and press SEQ again to cancel. Sequence order A ＞ B ＞ C ＞ D … ＞ A ＞ B … Sequence t...
Page 20 - Under the following circumstances, the system stops recording:
JPEG2000 Stand alone DVR User Guide - 20 - 3-8 Record Emergency record (Red): press REC to start emgergency record at continuous record mode and at the best resolution and quality. Schedule record (Green): record at the setup schedule, record mode, resolution and quality Stop record (White): the whi...
Page 23 - -9-7 Adjust Playback speed by IR remote controller
JPEG2000 Stand alone DVR User Guide - 23 - 3-9-6 Playback speed adjustments While playback, using the direction keys to adjust the playback speed. Speed up the playback Slow down the playback Rewind Play in forward direction The range of speed adjustment: 1/16X~1X, 1X~64X 3-9-7 Adjust Playback speed...
Page 26 - BAR
JPEG2000 Stand alone DVR User Guide - 26 - 4-2-2 Monitor setup 1.[VGA SETUP] Set up the VGA resolution. 2.[COLOR BAR TEST] Adjust the monitor colors by the color bar. VGA resolution setup: 1024*768/60HZ 、 800*600/60HZ 、 640*480/60HZ 、 1024*768/75HZ 、 800*600/75HZ 、 640*480/75HZ Monitor colors’ adjus...
Page 28 - ACTIVE
JPEG2000 Stand alone DVR User Guide - 28 - 4-3-2 Time/date setup The date and time set by the manufacturer maybe different from your time zone. It is very important to set up they system date and time before the DVR starts recording. Set the date and time by using direction buttons and [-][+] button...
Page 30 - BOX
JPEG2000 Stand alone DVR User Guide - 30 - [MOTION SETUP] 1.[CHANNEL] Select a channel for the setup. 2.[SENSITIVITY GRADE] Adjust motion detection sensitivity. 1 (LOW)~4 (VERY HIGH) 3.[MOTION DISPLAY TYPE] Setup the display type that marks the motion area. BOX - shows block / CELL - shows green lat...
Page 32 - AM
JPEG2000 Stand alone DVR User Guide - 32 - 4-3-6 Event popup setup 1.[CHANNEL] Use [+] and [-] to select a channel. 2.[POPUP ON/OFF] Set up the POPUP function ON/OFF: Use [+] and [-] to select ON or OFF. When there is an event, the screen display will switch to a full screen of the corresponding cha...
Page 33 - Admin
JPEG2000 Stand alone DVR User Guide - 33 - 4-3-8 Password setup The password consists of 1 to 8 digits. Press the number keys on the front panel to enter the password and you can use any combination of the numbers from 1 to 10 . 1.[USER ID] Press e or f to set User ID. 2.[USER PW] Key in the current...
Page 35 - IPS is refered to field per second.
JPEG2000 Stand alone DVR User Guide - 35 - 4.[RESOLUTION] By lowering the resolution, the DVR gains the recording speed but the recorded pictures becom smaller. Video system Full Mode Dual Mode Quad Mode NTSC 60IPS@720*240 120IPS@360*240 240IPS@360*120 4CH PAL 50IPS@720*288 100IPS@360*288 200IPS@360...
Page 37 - AJP
JPEG2000 Stand alone DVR User Guide - 37 - 4-4-3 Holiday setup Set up the holidays through out the year. You can program up to 100 days as holidays. The recording schedule of the holidays is the same as the settings of Sunday. Press MODE and set the editing mode as EDIT HOLIDAY. Use direction key to...
Page 40 - setup
JPEG2000 Stand alone DVR User Guide - 40 - [CONNECTION SETUP] Use to select and [+] [-] or J.Shuttle to change the value. 1.[TIMEOUT] Set up the remote connection response time, if the client does not receive responses from the DVR for certain duration, the client will disconnect the connection and ...
Page 41 - CHAP.6 PTZ Camera Control
JPEG2000 Stand alone DVR User Guide - 41 - 4-6-3 Pantilt setup < COMMAND SETUP > < SPEED SETUP > [COMMAND SETUP] Press to select and [+] / [-] to change the value. 1.[CHANNEL] Select PTZ channel. 2.[MODEL] Select PTZ protocol. 3.[PTZ ID] Select PTZ ID. 4.[BUADRATE] Select Baud Rate of PT...
Page 44 - CD Player software installation
JPEG2000 Stand alone DVR User Guide - 44 - 5-2 CD Player software installation 1.Insert software CD. 2. Click [Install CD-R backup player] to start the installation. 3. Select a Destination Folder 4. Copy files to the Destination Folder. System will build a new icon of [CD BACKUP PLAYER] on PC [DESK...
Page 45 - CD Player software interface; Fast Rewind Fast Forward
JPEG2000 Stand alone DVR User Guide - 45 - 5-3 CD Player software interface 1.Display screen: To display the backup image 2.Time display: To indicate the current time 3.Information window: To indicate the CD’s start/end time and date, and the backup video quality (resolution). 4.Speed Adjustment: Sp...
Page 46 - Open AJP file
JPEG2000 Stand alone DVR User Guide - 46 - Open AJP file 1. Select (OPEN) and the window below will show up on the screen. 2. Select the file and click [OPEN] to open the AJP file. Save JPG file 1. During playback and under FULL SCREEN MODE, when you see the picture you want to save, click EDIT. 2. ...
Page 47 - -1 PTZ camera Installation
JPEG2000 Stand alone DVR User Guide - 47 - 6-1 PTZ camera Installation 6-1-1 Connection Setup Connect the PTZ’s D+ to the DVR’s D+, and D- to D-. 6-1-2 PTZ setup [EXTERNAL DEVICE] SYSTEM MENU ` EXTERNAL DEVICE ` PANTILT SETUP ` COMMAND SETUP 1. [MODEL]: select a PTZ protocol. 2. [PTZ ID]: enter the ...
Page 48 - -2 PTZ camera operation
JPEG2000 Stand alone DVR User Guide - 48 - 6-2 PTZ camera operation Use MENU and NEXT key to select a PTZ command, and [+] [-] to select the channel. Then, press PTZ key to enter the PTZ control mode. Indicate the channel connected with a PTZ camera. Indicate PTZ command, press ENTER to send control...
Page 49 - -1 Network Introduction; -2 Network installation and setup; CHAP.7 Network and client software
JPEG2000 Stand alone DVR User Guide - 49 - 7-1 Network Introduction Users have to indentify what kind of Internet access they have before they set up the DVR’s network parameters. DSL and cable modem are the most popular broadband technologies. ADSL- Asymmetric Digital Subscriber Line ADSL is one of...
Page 54 - Client software
JPEG2000 Stand alone DVR User Guide - 54 - 7-4 Client software 7-4-1 Install and setup Insert the Install CD into CD-ROM, and the computer will auto-run the Install program. We suggest installing the software on Windows XP or Windows 2000. 1.[Install Client software] Click [Install Client software]....
Page 55 - Remote Control of PTZ:
JPEG2000 Stand alone DVR User Guide - 55 - 7-4-3 Software operation [Remote viewer interface] 1.[Live Display] Remote DVR Live display 2.[Current Status ] To show the current status 3.[PTZ Camera Control ] To control PTZ Camera Zoom/Focus/Direction ※ Remote Control of PTZ: 1) Set up PTZ at DVR first...
Page 56 - “ADMIN”
JPEG2000 Stand alone DVR User Guide - 56 - 7-4-4 Client software setup [IP/PORT] 1.[DVR NAME] Enter the DVR’s location or name 2.[IP LIST] Show the list of saved DVR IP addresses. If you are connecting to a DVR in this list, you can simply click it from the list, enter the DVR Admin’s password, and ...
Page 57 - -5 DDNS setup and operation for details.; Click OK and then click CONNECT from Remote Viewer Interface.
JPEG2000 Stand alone DVR User Guide - 57 - [DDNS] 1.[Group] Enter Group name registered on DDNS Server. Please refer to 7-5 DDNS setup and operation for details. 2.[DVR Name] Enter DVR name registered on DDNS Server. If the DVR name is entered and saved before, click LOAD to browse the list. 3.[Save...
Page 59 - Remote Playback Interface
JPEG2000 Stand alone DVR User Guide - 59 - 7-4-6 Remote playback When the DVR is connected, click [PLAYBACK] to enter Playback interface. [ Remote Playback Interface ] 1.[Playback Picture] To show the playback video 2.[Time/Date Selection] To select time/date of playback 3.[Record and Playback Statu...
Page 62 - -5 DDNS setup and operation; DDNS SERVER setup
JPEG2000 Stand alone DVR User Guide - 62 - 7-5 DDNS setup and operation DDNS SERVER setup 1. Connect to DDNS SERVER(http://advr.com.tw or http://59.124.143.151) by IE browser Select [REGISTER] to register a new account 2. Add a new account Group: Add a new user name User Password: Add user password ...
Page 64 - DVR setup; -2 Network installation and setup for details.; Client software setup
JPEG2000 Stand alone DVR User Guide - 64 - DVR setup 1. The DVR setup is a onetime effort. First, make sure your DVR can be accessed over the Internet. Please refer to 7-2 Network installation and setup for details. 2. Go to [SYSTEM MENU] f [ [EXTERNAL DEVICE] f [TCP/IP SETUP] f [DDNS SETUP] DDNS ON...
Page 65 - GROUP; Get IP; IP Address
JPEG2000 Stand alone DVR User Guide - 65 - 2. Select DDNS in [IP/PORT] setup 3.Go to DDNS setup [DDNS INFO] GROUP : Enter Group nameregistered on DDNS Server. DVR NAME : Enter DVR name registered on DDNS Server. If the DVR name is entered and saved before, click LOAD to browse the list. Save/Load : ...
Page 66 - Configuration of DDNS connection
JPEG2000 Stand alone DVR User Guide - 66 - Configuration of DDNS connection 1. DVR connect to DDNS server automatically and update the IP address by itself. 2. The client accessesto DDNS server and requests IP address from DDNS server. 3. DDNS server replies the DVR’s IP address and port number. 4. ...
Page 67 - Remote Live View via IE Browser
JPEG2000 Stand alone DVR User Guide - 67 - Users can also access to the DVR from Internet Explore for remote viewing, remote backup, and playback the backup file. Log on to DDNS server and go to the DVR List Remote Live View via IE Browser Click WEB to link to your DVR 1.[Live picture] Shows the liv...
Page 68 - Web Network Backup
JPEG2000 Stand alone DVR User Guide - 68 - PTZ: Select the protocol BAUDRATE: Select the baud rate CH: Select the ID of PEZ camera ZOOM: Zoom in/out FOCUS: Focus near/far IRIS: IRIS open/close Web Network Backup Click “Backup” to open the web page “Web Network Backup” 1.Backup Information: IP Addres...
Page 69 - Backup Procedure
JPEG2000 Stand alone DVR User Guide - 69 - 2. Function setup: Connect Test: To test the connection status Unlock: To get the record start/End time of DVR Set Backup Time: Set the start/end time, size and path of file backup Start Backup: Active the backup function 3. The information of DVR Server: R...
Page 70 - Play backup file
JPEG2000 Stand alone DVR User Guide - 70 - Play backup file Click [Backup Player] to open the web page of “Backup Player” 1. Display the backup image 2. Indicate the present time of monitoring 3. Indicate the start/end time of backup file 4. Switch to the different modes of multi-screen 5. Channel s...
Page 72 - The numbers are for reference only.; Appendix.1 Record time table
JPEG2000 Stand alone DVR User Guide - 72 - [4ch DVR] ※ The numbers are for reference only. ※ The recording duration is caculated under the continuous recording mode (Record speed :1/1X) Appendix.1 Record time table
Page 74 - Appendix.2 System configuration
JPEG2000 Stand alone DVR User Guide - 74 - Appendix.2 System configuration
Page 75 - Install USB driver; Firmware upgrade
JPEG2000 Stand alone DVR User Guide - 75 - Install USB driver 1. Connect USB port between PC and DVR 2. Press and hold Search and Play keys on front panel and power on DVR 3. The DVR beeps for a moment. 4. When the Windows system detect new device, please select [Install from a list or specific loca...
Page 77 - Install USB upgrade program; After installation, there’ll be a shortcut on desktop.
JPEG2000 Stand alone DVR User Guide - 77 - Install USB upgrade program Insert the Install CD 1.Please select :[Install USB upgrade program(Allupdate) 2. Set up Directory ※ (default Directory : "C:\Program Files\J2000\Allupdate\") After installation, there’ll be a shortcut on desktop. Click o...
Page 78 - Upgrade firmware; Update procedures; Step 1 update BOOT
JPEG2000 Stand alone DVR User Guide - 78 - Upgrade firmware Update procedures Step 1 、 Update BOOT 1. Connect the USB port between DVR and PC. (Do not power on DVR in advance) 2. Execute USB update program AUDTOTAL ， select “Boot” then choose the file: _FBoot_0000_16M_V2.04.bin 3. Press and hold SEA...
Page 80 - Introduction; Play only mode
JPEG2000 Stand alone DVR User Guide - 80 - Introduction PLAY ONLY MODE can be used in the following situations: When you need to playback a hard drive from another DVR When you need to playback the video which you deleted by running HDD CLEAR Enter “PLAY ONLY MODE” Turn on the DVR. At the initial sc...
