Hitachi CP-X705 - Manual
Hitachi CP-X705 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Initial set signals; and H POSITION in the IMAGE menu.
- Page 3 – HDMI; RGB OUT; At RGB signal
- Page 4 – VIDEO
- Page 5 – • 500 mVrms 1kΩ output impedance; REMOTE CONTROL
- Page 6 – LAN
- Page 7 – RS-232C Communication; Turn off the projector and the computer.; Communications setting; CRC_low : Lower byte of CRC flag for command data; Classification
- Page 9 – Communication Port; The following two ports are assigned for the command control.; Command Control Settings; Port Settings
- Page 10 – Command Format; CRC_low: Lower byte of CRC flag for command data; Requesting projector status (Get command)
- Page 11 – Decreasing the projector setting value (Decrement command); ‘xxxxH’; When authentication error occurred.; NOTE
- Page 12 – ‘xxH’; Automatic Connection Break
Projector
CP-X705/CP-X615
User's Manual – Operating Guide
Technical
Example of computer signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz)
Rating
Signal mode
720 x 400
37.9
85.0
VESA
TEXT
640 x 480
3.5
59.9
VESA
VGA (60Hz)
640 x 480
37.9
72.8
VESA
VGA (72Hz)
640 x 480
37.5
75.0
VESA
VGA (75Hz)
640 x 480
43.3
85.0
VESA
VGA (85Hz)
800 x 600
35.2
56.3
VESA
SVGA (56Hz)
800 x 600
37.9
60.3
VESA
SVGA (60Hz)
800 x 600
48.
72.2
VESA
SVGA (72Hz)
800 x 600
46.9
75.0
VESA
SVGA (75Hz)
800 x 600
53.7
85.
VESA
SVGA (85Hz)
832 x 624
49.7
74.5
Mac 6” mode
024 x 768
48.4
60.0
VESA
XGA (60Hz)
024 x 768
56.5
70.
VESA
XGA (70Hz)
024 x 768
60.0
75.0
VESA
XGA (75Hz)
024 x 768
68.7
85.0
VESA
XGA (85Hz)
52 x 864
67.5
75.0
VESA
52 x 864 (75Hz)
280 x 960
60.0
60.0
VESA
280 x 960 (60Hz)
280 x 024
64.0
60.0
VESA
SXGA (60Hz)
280 x 024
80.0
75.0
VESA
SXGA (75Hz)
*280 x 024
9.
85.0
VESA
SXGA (85Hz)
*600 x 200
75.0
60.0
VESA
UXGA (60Hz)
280 x 768
47.7
60.0
VESA
W-XGA (60Hz)
400 x 050
65.2
60.0
VESA
SXGA+ (60Hz)
NOTE
• Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(600x200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.
• The HDMI input does not support the signals marked with *.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Dis...
3 D HDMI • Type :Digital audio/video connector • Audio signal : Linear PCM (Sampling rate; 32/44./48 kHz) Connection to the ports A RGB 1, B RGB OUT D-sub 5pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative)...
4 VIDEO CONTROL AUDIO IN 1 AUDIO IN 2 AUDIO OUT RGB OUT RGB1 RGB2 HDMI R L R L AUDO IN 3 AUDIO IN 4 LAN C B /P B Y C R /P R B/C B /P B B/C R /P R G/Y H V USB REMOTE CONTROL Connection to the ports (continued) 4 3 2 I VIDEO RCA jack• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43 • 1.0±0.1Vp-p, 75Ω...
