Page 2 - TABLE OF CONTENTS
2 F-050202L TABLE OF CONTENTS OWNER’S INFORMATION 4 SAFETY PRECAUTIONS 4 INTERNATIONAL PICTORIALS 7 ASSEMBLY 8 OPERATION 11 MAINTENANCE 14 TROUBLE SHOOTING CHART 20 REPAIR PARTS 22 Declared vibration emission values in accordance with Directive 98/37/EC. Vibration Emission according to EN 836/A2:200...
Page 3 - LIMITED WARRANTY
3 F-050202L Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase. The manufacturers of the engine and battery pack system (where applicable) fu...
Page 4 - SAFETY RULES; OWNER’S INFORMATION; Responsibility Of The Owner; The responsibility of the owner is; General Operation
SAFETY RULES 4 F-050202L OWNER’S INFORMATION Know your product: If you understand the unit and how the unit operates, you will get the best performance. As you read this manu- al, compare the illustrations to the unit. Learn the location and the function of the controls. To help prevent an accident,...
Page 7 - INTERNATIONAL PICTORIALS; Safety Warning Pictorials
SAFETY RULES 7 F-050202L INTERNATIONAL PICTORIALS IMPORTANT: The following pictorials are located on your unit or on literature supplied with the product. Before you operate the unit, learn and understand the purpose for each pictorial. 1 2 6 7 3 8 4 5 9 Safety Warning Pictorials 1 WARNING 2 IMPORTA...
Page 8 - ASSEMBLY; Owner’s Manual; TOOLS REQUIRED; TO REMOVE THE
ASSEMBLY 8 F-050202L ASSEMBLY CONTENTS OF PARTS BAG 1 - Owner’s Manual 1 - Parts Bag 1 - Safety Glasses (Not shown actual size) 2 Sets - Trimmer Lines (0.155 inch diameter) 1 - Bag (4 Screws) WARNING: Always wear safety glasses or eye shields while as- sembling the machine. TOOLS REQUIRED 1 - Knife ...
Page 9 - HOW TO RAISE THE HANDLE
ASSEMBLY 9 F-050202L HOW TO RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position. 3. Stand in the operator’s position b...
Page 10 - ENGINE PREPARATION; Fill Crankcase With Oil; CHECKLIST
ASSEMBLY 10 F-050202L ENGINE PREPARATION Note: Engine does not contain OIL or PETROL. WARNING: Follow the engine manufacturer’s instructions for the type of petrol and oil to use. Always use a safety petrol container. Do not smoke when adding petrol to the en- gine. When inside an enclosure, do not ...
Page 11 - OPERATION; KNOW YOUR POWERTRIM; Trimmer Head Drive Lever -; EYE PROTECTION
OPERATION 11 F-050202L KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERATE the machine. To familiarise yourself with the location of the controls, compare the illustrations with your machine. Save this handbook for future reference. ÎÎÎ ÎÎÎ ÎÎ ÎÎ Trimmer Head Figure...
Page 13 - HOW TO START THE ENGINE
OPERATION 13 F-050202L HOW TO START THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. WARNING: Never leave the ma- chine unattended while the en- gine is running. Wait for the trim- ...
Page 14 - MAINTENANCE; CUSTOMER RESPONSIBILITIES; SERVICE RECORDS; PRODUCT SPECIFICATIONS
MAINTENANCE 14 F-050202L CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SERVICE DATES Check Engine Oil Level √ Check trimmer Lines √ 1 Check Trimmer Head Engagement √ Engine/Machine Cleani...
Page 15 - LUBRICATION
MAINTENANCE 15 F-050202L LUBRICATION How To Lubricate The Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly. Use a grease gun with au- tomotive type grease to lubricate the jackshaft assembly as shown in Figure 10. Figure 10 Grease Fitting How To Change Engine Oil C...
Page 16 - SPARK PLUG
MAINTENANCE 16 F-050202L SPARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked.1. Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire bru...
Page 17 - SERVICE AND ADJUSTMENT
MAINTENANCE 17 F-050202L SERVICE AND ADJUSTMENT WARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. HOW TO REPLACE THE TRIMMER LINE For the best performance, use a heavy gauge 3.3mm (0.130”...
Page 18 - HOW TO
MAINTENANCE 18 F-050202L HOW TO REPLACE THE DRIVE BELT To replace the drive belt, the trimmer head and shield must be removed as follows. WARNING: Before you remove the drive belt, disconnect the wire from the spark plug. 1. Remove the two fasteners that hold the rear of the shield to the trimmer ho...
Page 19 - STORAGE; Trimmer
MAINTENANCE 19 F-050202L STORAGE WARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirty days or more, follow the steps below to make sure the machine is in good condition the...
Page 20 - TROUBLE SHOOTING CHART; TROUBLE
TROUBLE SHOOTING CHART 20 F-050202L TROUBLE CAUSE CORRECTION Engine does not start Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug. Fuel tank empty. Add fuel. Dirty carburetor or fuel li...
Page 22 - REPAIR PARTS
Code 407C REPAIR PARTS 22 F-050202L 1 2 3 4 5 28 6 2 7 6 8 4 9 10 9 10 4 11 16 17 11 14 12 15 14 20 22 29 23 27 16 19 30 17 6 20 25 24 31 26 33 1932 32 34
Page 23 - Key
Code 407C REPAIR PARTS 23 F-050202L Key No. Description Part No. 1 Lever, Stop MU740198E549 2 Bolt MU323035 3 Cable, Control Latching MU740193 4 Tie, Cable MU071372 5 Handlebar MU740196E701 6 Nut MU15x116 7 Control, Throttle MU740194 8 Guide, Rope MU672510 9 Knob, Handlebar MU740202 10 Washer MU7830...
Page 26 - NOTES
Page 28 - How To Order Replacement Parts
28 F-050202L How To Order Replacement Parts Use only manufacturer’s authorised or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a PA for purchased assembly. It is important that you include this when ord...
