Page 5 - CONTENTS
1.3 Main Features / Specifications 1.5 Contents 1.6 Introduction 1.7 Warranty 1.8 - 1.11 Safety Precautions 1.8 - Training 1.8 - 1.9 - Preparation 1.9 - 1.10 - Operation 1.10 - 1.11 - Maintenance and Storage 1.11 - Safety Symbols 1.11 - Decal Symbols 1.12 Assembling the Mower 1.12 - Delivery Checkli...
Page 6 - INTRODUCTION
1.6 INTRODUCTION Thank you for purchasing an Allen machine. The following pages are designed to help you gain safe and efficient service from your machine. IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the mower as it gives essential information regarding mower safety, operation, m...
Page 7 - WARRANTY
1.7 WARRANTY LIMITED WARRANTY Allen mower’s are manufactured by Hayter Limited. The manufacturer warrants to the original user/purchaser that this unit shall be free from defects inmaterial and workmanship under normal use and service for a period of one year from the date of purchase. The manufactu...
Page 8 - Safety Alert Symbol
1.8 SAFETY PRECAUTIONS This safety alert symbol indicates important safety messages. Whenyou see this symbol be alert to the possibility of injury. Carefully readthe following and inform others. Your machine is perfectly safe if used correctly. Failure to observe thefollowing precautions may result ...
Page 10 - SAFETY PRECAUTIONS
1.10 Do not put hands or feet near or under rotating parts. Never pick up or carry the machine while the engine is running. Never touch the exhaust/exhaust guard or cooling fins when the engineis hot. Stop the engine and disconnect the spark plug lead: - Before clearing blockages. - Before cleaning/...
Page 11 - Maintenance & Storage; Information Symbols
1.11 SAFETY PRECAUTIONS If the fuel tank has to be drained, this should be done outdoors andwhen the engine is cool. Wear strong work gloves when removing and reassembling the cuttingdevice. Always replace worn or faulty parts with genuine Allen parts. Maintenance & Storage Safety Symbols Safety...
Page 12 - ASSEMBLING THE MOWER
Remove the machine from the packaging and check that the followingitems have been supplied correctly. If any items are missing contact,your local dealer. Main deck, lower and upper handlebars. 1. Handlebar bolt x 2 5. Spanner x 1* 9. Handwheel x 2* 2. Bush x 4 6. Ties x 2* 3. Nut x 2 7. Ties* 4. Was...
Page 13 - Prevent Engine Damage; Oil Type
To prevent engine damage the engine is shipped without oilor petrol. The engine must be filled with the correct gradeof oil and petrol before starting. Always use high quality detergent oil classified SAE 10W-30.Never use additives with recommended oil.To prolong the life of your engine it is import...
Page 14 - Controls
Check that the engine stop lever moves freely and returns to it’s restposition when released. 1. Open the fuel tank vent by turning the vent knob at least 2 or 3 turns counterclockwise. 2. Turn the fuel valve lever to the ON position. 3. To start a cold engine, move the choke lever to the CLOSED pos...
Page 15 - OPERATING; Cutting Grass; Continued; Stopping
1.15 OPERATING 4. Hold the handlebar together with the engine stop lever, place your foot on the deck and tilt the mower towards you. This will take the load off the engine making it easier to start. Pull the starter grip lightly until you feel resistance, then pull briskly. Return the starter grip ...
Page 16 - OPERATING THE MOWER; Adjusting the Cutting Height
The cutting height of your mower has been set at the highest position (1). If you prefer a lower cut followthese instructions: a. Turn the petrol tap to the off position and where fitted the vent screw. b. Disconnect the spark plug lead. c. Tilt the mower to its side. (Keeping the carburet -tor uppe...
Page 18 - Air Cleaner Service
1.18 MOWER MAINTENANCE To service the air cleaner remove the air cleanercover (1) by releasing two top catches (2) and tilting away from body until lower tabs release. Remove cartridge (3) and clean by tapping gentlyon a flat surface. If very dirty or damaged replace. - Do not brush- Do not use petr...
Page 20 - Storage; MOWER
Storage Change the engine oil after the first 5 hours of operation and thereafteraccording to the ‘Maintenance Schedule’:- 1. Drain fuel by running the engine until the fuel tank is empty. 2. Remove the spark plug lead. 3. Allow the engine to cool. 4. Drain the oil while the engine is warm.(Not hot)...
Page 21 - EC DECLARATION OF CONFORMITY; CONFORMITY
EC DECLARATION OF CONFORMITY Manufacturer: HAYTER LIMITED,Address: Spellbrook, Bishop’s Stortford, Herts. CM23 4BU. ENGLAND declare that the trimmer : Model name: Model No: Cutting width:Speed of rotation of thecutting device:Engine Manufacturer:Speed of rotation of engine: XR44 CODE 184E40 cm 4800 ...
Page 23 - TROUBLE
PROBLEM POSSIBLE FAULT REMEDY Engine vibrates excessively Mounting bolts loose. Tighten bolts Cutter disc bolt loose. Tighten bolt Bent crankshaft. Consult your dealer Damaged impeller or cutter disc Consult your dealer Uneven cut Flexiblade out of balance Replace flexiblade Engine running slow Cons...
Page 24 - MAINFRAME
1.24 Item No. Description Part No. Qty Item Note 1 ALLEN XR44 DECAL 1 1 1 - 1 5 1 6 1 2 ALLEN XR16 DECAL ONLY 1 1 1 - 1 8 2 5 1 3 WASHER 1/4*7/8*.08" THK 0 9 2 6 3 2 4 NUT M6 NYLOC 'T' TYPE 0 9 4 3 8 3 5 CABLE TIE H Y 3 9 6 6 3 NOT SHOWN 6 BOLT M6*45 0 9 5 6 8 1 7 SCREW PLASTITE DIA 5*22 PAN POZ...
Page 26 - NOTES
Page 27 - CUSTOMER INFORMATION
1.27 Serial No: Engine Type:- GXV57 Engine:- Honda Engine Type:- GXV57 Engine:- Honda Date of Sale:- Your Local Dealer:- CUSTOMER INFORMATION 111-1519 (A) 28/1/08 4:44 pm Page 1.27
Page 28 - Manufactured by Hayter Limited; Hayter Limited
Manufactured by Hayter Limited Hayter Limited Spellbrook, Bishop’s Stortford, Herts, CM23 4BU, England.Tel: +44 (0) 1279 723444 Fax: +44 (0) 1279 600338e-mail: [email protected] www.hayter.co.uk YOUR HAYTER DEALER IS: 111-1519 (A) 28/1/08 4:44 pm Page 1.28
